i
DAFTAR PUSTAKA
Amstead. B.H, F.Osatawaid, P, l.Begeman.M, Djaprie.s, 1922, Teknologi Mekanika, Jilid I, UI- Jakarta, Erlangga,
Anonim, 1964, Metals Handbook, Vol. 2, Heat Treating, Cleaning and Finishing, 8th edition.
Anonim, 1977, Atlas of Isothermal Transformation and Cooling Transformation Diagrams, ASM Metal Handbook, Metals Park, Ohio.
Anonim, 1985, ASM Handbook Commite, Metallography and Microstructure, American Society for Metal.
Aisi 4340”, Tugas Akhir S – 1, Teknik Material dan Metalurgi
Institut Teknologi Sepuluh Nopember, Surabaya.
Berglund, P.L., 2006, A Woodworker’s Guide to Tool Steel and Heat Treating.
http://www.threeplanes.net/toolsteel.html. Diakses tanggal 20 mei 2010 jam 12.30.
Brooks, C. R., 1979, Heat Treatment of Ferrous Alloys, Hemisphere Publishing Corporation, USA.
ii
Callister, W.D., 2007, Material Science and Engineering An Introduction 7th, John Wiley & Sons, Canada
. Dieter, George E. 2000. Engineering Design “Third Edition”. Univ. of Maryland. Mc Graw Hill International.
DonnyAndryanto, 2004, Pack Nitriding pada Baja Karbon Rendah yang Dideformasi, Tugas Akhir S1, ITB, Bandung.
Elgun, S.Z., 1999, Case Hardening Methods, Farmingdale jurnal.http://info.lu.farmingdale.edu/depts/met/met205/casehardening.html.
diakses tanggal 20 Mei 2010 jam 12.15.
Gandy, D., 2007, Carbon Steel Handbook, Electric Power Research Institute, Final Report, (March 2007), p. 31-56. http://www.apri.com/1014670. Diakses dari APRI tanggal 3 juni 2010 jam 07.24.
Haqi, M.I., 2006, Hardening Pada Baja Karbon Tinggi, Open and Knowledge Education Journal. http://www.oke.or.id/journal.02726.
Diakses dari tanggal 6 Mei 2010 jam 05.22.
Hayden, H.W., Moffatt, W.G., and Wulff, J., 1965, Structure and Properties of Materials, Vol. III, Mechanical Behavior, John Wiley & Sons,
New York.
iii
John, V.B., 1983, Introduction to Engineering Materials, 2nd, The Macmillan Press Ltd., London.
Kreith, F., 1997, Prinsip-prinsip Perpindahan Panas (terjemahan Arko Prijono, 1997), Edisi ketiga, Erlangga, Jakarta.
Rao. P.N., 2002, Manufacturing technology Metal Cutting and Machine tools, Faculty of Mechanical Engineering, University Teknology,
MARA Shah Alam, Malaysia.
Smallman, R.E., Bishop, R.J., 2000, Metalurgi Fisik Modern dan Rekayasa Material (penerjemah Sriati Djaprie, 2000), Erlangga,
Jakarta.
Surdia.T, Saito, S, 2000, Pengetahuan Bahan Teknik., Cetakan
ke-5 Pradya Paramita Jakarta.
Suarsana, I Ketut. 2005. Praktikum Ilmu logam Universitas Udayana, Jurusan Teknik Mesin Fakultas Teknik. Denpasar.
Thompson, M., Ferry, M., and Manohar, P.A., 2000, Simulation of Hot-band Microstructure of C–Mn Steels during High Speed
Cooling, ISIJ International, Vol. 41, (April 2001), pp. 891–899. http://www.unsw.edu.au. Diakses tanggal 3 Juni 2010 jam 07.00.
iv
Van Vlack, L. H., 1992, Ilmu dan Teknologi Bahan (penerjemah Sriati Djaprie, 1992), Erlangga, Jakarta.
