• Tidak ada hasil yang ditemukan

PENGARUH VARIASI PEMBEBANAN TERHADAP KEAUSAN FASE RUNNING-IN PADA SISTEM ROLLING SLIDING CONTACT - Diponegoro University | Institutional Repository (UNDIP-IR)

N/A
N/A
Protected

Academic year: 2017

Membagikan "PENGARUH VARIASI PEMBEBANAN TERHADAP KEAUSAN FASE RUNNING-IN PADA SISTEM ROLLING SLIDING CONTACT - Diponegoro University | Institutional Repository (UNDIP-IR)"

Copied!
2
0
0

Teks penuh

(1)

42

DAFTAR PUSTAKA

[1] en.wikipedia.org/gear & en.wikipedia.org/piston & en.wikipedia.org/sprocket ( diakses 20 September 2011)

[2] Jamari, J. (2006). Running-in of rolling contacts. PhD Thesis, University of Twente, Zutphen, The Netherlands.

[3] Akbarzadeh, S., Khonsari. MM., On the prediction of the running-in behavior in mixed-lubrication line contact., Journal of Tribology - Transactions of the ASME

2010, 132 : 032102-1 – 032102-11.

[4] Blau, P.J., 1989, Friction and wear transitions of materials, Noyes, Park Ridge, NJ.

[5] Kraghelsky, V., Dobychun, M.N. and Kombalov, V.S., 1982, Friction and wear calculation methods, Pergamon Press, Oxford.

[6] Kajdas, C., Harvey S.S.K., and Wllusz E., 1990, Ensiklopedia of tribology, Elseiver, Amsterdam, The Netherlands.

[7] Bhushan, B. (1949). Modern tribology handbook, vol. 1, CRC Press, Washington, D.C.

[8] Whitehouse, D.J., 1980, “The effect of surface topography on wear,” Fundamentals of Tribology, edited by Suh and Saka, MIT, pp. 17 – 52.

[9] Wang, W., Wong, P. L., and Zhang, Z., 2000, Experimental study of the real time change in surface roughness during running-in for PEHL contacts,” Wear, 244, pp. 140-146.

[10] Patir, N., and Cheng, H. S., 1978, “An average flow model for determining effects of three-dimensional roughness on partial hydrodynamic lubrication,” ASME J.

Lubr. Technol., 100, pp. 8–14.

(2)

43

[12] Akbarzadeh, S., Khonsari. MM., Experimental and theorical investigation of running in. tribology International, 44. (2011) 92-100.

[13] http://en.wikipedia.org/slip (diakses 22 September 2011)

[14] Zum – Gahr, K. H. 1987. Microstructure and wear of materials. Elseiver, Amsterdam, The Netherlands.

[15] Hokkirigawa, K. and Kato, K. (1989). „Theoretical estimation of abrasive wear resistance based on microscopic wear mechanism‟, Wear of Materials (ed K.C. Ludema), ASME, New York, pp. 1–8.

[16] Stachowiak, Gwidon W. (2005) Wear – Materials, mechanisms and practice. John Wiley & Sons, Ltd., West Sussex, England.

[17] Gelinck, Edwin, 1999, Mixed lubrication of line contact, Ph.D. thesis, University of Twente, Enschede, The Netherlands.

[18] Schipper, D.J., 1988, Transitions in the lubrication of concentrated contacts, PhD Thesis,University of Twente, Enschede, The Netherlands.

[19] Faraon, I. C., 2005, Mixed lubricated line contact, Ph.D. thesis, University of Twente, Enschede, The Netherlands.

[20] Wang, W., Wong, P. L., and Guo, F., 2004, Application of partial elastohydrodynamic lubrication analysis in dynamic wear study for running-in,”

Wear, 257, pp. 823–832.

Referensi

Dokumen terkait

Tugas Sarjana dengan judul “ Prediksi Keausan Pin pada Pin-On-Disc Sliding Contact System Menggunakan Metode Elemen Hingga ” telah disetujui pada:.. Hari

Callister, William D, Jr., 1997, Materials Science and Engineering an Introduction, Fourth Edition, John Wiley & Sons.. Dieter, Gerorge E, 1987, Metalurgi Mekanik, Edisi Ketiga

Diajukan Sebagai Salah Satu Tugas dan Syarat Untuk Memperoleh Gelar Sarjana (S-1).

HALAMAN DAFTAR TABEL ... Tujuan penulisan ... Batasan masalah ... Metodologi penelitian ... Sistematika penulisan ... Pengertian keausan ... Jenis-jenis keausan dan

for wear modeling on 3D contact and rolling-contact problems. Diktat Metode Elemen Hingga. Fakultas Teknik-Jurusan. Teknik Mesin Universitas

Neufert, Ernst, Architects Data, New York, John Wiley & Sons, Inc: 1980. Lawson, Fred, Hotel and Resort Planning Design and

- Broadbent, Geoffrey, 1990, Design in Architecture, Architecture and Human Sciences, John Wiley &. Sons,

Dalam hal ini penulis mengembangkan suatu model baru “present model” untuk kasus line contact yang dikombinasikan dengan load sharing concept untuk memprediksi