SPATIAL ANALYSIS FOR LAND CAPABILITY ASSESSMENT IN
THE UPSTREAM OF WAMPU WATERSHED USING
GEOGRAPHIC INFORMATION SYSTEM
By:
Rahmawaty
a, Sari Adryana
a, Ahmad Sofyan
b, Abdul Rauf
c aForestry Study Program, Faculty of Agriculture, Sumatera Utara University,bBP DAS Wampu Sei Ular, Ministry of Forestry
cAgroecotecnology Study Program, Faculty of Agriculture, Sumatera Utara University,
Medan, North Sumatra, Indonesia
Address: Jl. Tri Dharma Ujung No. 1 Kampus USU, Medan, 20155, North Sumatra, INDONESIA email: [email protected]
ABSTRACT
Land utilization in Wampu Hulu Sub Watershed should be based on its land capability.
This research was conducted in March-September 2011 at Wampu Watershed, Langkat,
North Sumatra, Indonesia. Land capability classification was conducted by spatial
analysis for capability of land criteria using Geographic Information System (GIS)
(overlay technique). The land criteria are slope, soil erodibility, level of erosion hazard,
soil depth, soil texture, permeability and drainage. Soil analyze was done in order to
obtain the data of soil texture, permeability, soil erodibility, while slope, soil depth, level
of erosion hazard and drainage was obtain from land system map. The result showed that
the land capability classification at Wampu Hulu Sub Watershed, divided by three
classes, namely: Class III, V, and VI.
Keywords: Geographic Information System, Land Capability, Overlay, Wampu
Watershed
I. INTRODUCTION
Land capability is defined as the inherent capacity of land to perform under a given
use; thus, land capability classification (LCC) is the description of a landscape unit in
terms of its inherent capacity to sustain a desirable combination of flora and fauna. It is
the first approximation in the process of subdividing a land use planning unit into land
2
capabilities are slope, elevation, climate, topographic, landform, vegetation, geology,
soils and fauna (Oszaer, 1994).
The important event that has occurred in Wampu Watershed was a flash flood
event on November 2, 2003. The flood that occurred in the upstream of Wampu
Watershed was resulting land cover change on the physical conditions. After eight years
of flooding, of course, there has been a lot of changes in land use. Incompatible land use
will also worsen the condition of the Wampu Watershed which is a watershed in the
category needs to be restored supportability. Therefore, it is necessary to do research on
the capability of the land in Wampu Watershed using spatial analysis (overlay technique)
that can be done with software of Geographic Information Systems (GIS).
Research on the classification of land capability especially after flash floods in
Wampu watershed area using GIS has not been done before. Therefore, the data and
information regarding the capability of the land needs to be studied further. This study
aimed to map the land capability class in the upstream of Wampu Watershed.
II. MATERIALS AND METHODS
This research was conducted in March until September 2011, in the upstream
of Wampu Watershed ( Figure 1 ) .
3
Land capability classification (LCC) was evaluated based on FAO guidelines
(FAO, 1976). Land capability classification was done is based on criteria in Arsyad
(2006). According to Morgan (1986) cited by Oszaer (1994), the objective of the
classification is to regionalize an area of land into units with similar kinds and degrees of
limitations. The basic unit is the capability unit. This consists of a group of soil types
of sufficiently similar conditions in terms of profile form, slope and degree of erosion as
to make them suitable for similar crops and warrant the use of similar conservation
measures. Furthermore, the capability units are combined into sub-classes according to
the nature of the limiting factor and these, in turn, are grouped into classes based on the
degree of limitation. The criteria and description of Land Capability Classes were based
on FAO, 1976 and Arsyad, 2006. The GIS spatial analysis was used to overlay to all
thematic maps.
III. RESULTS AND DISCUSSION
Based on Langkat Administration Map in 2010, the upstream of Wampu
Wateeshed is located in 5 districts, namely: Bahorok Sub-District, Kutam Sub-District,
Sirapi Sub-District, Wampu Sub-District, and Selesai Sub-District (Figure 2). The
upstream of Wampu Watershed bordered with Batang Serangan Sub-District in Northern,
Salapi Sub-District and Kuala Sub-District in Southern, Binjai Sub-District and Stabat
Sub-District of the Eastern, and Aceh Tenggara District, Aceh Province in the west.
There are 12 land systems in the upstream of Wampu Watershed, namely : Bakunan
(BKN), Pakasi (PKS), Batuapung (BTG), Pandreh (PDH), Bukit Pandan (BPD), Lubuk
Sikaping (LBS), Gunung Gadang (GGD), Maput (MPT), Taweh (TWH), Kalung (KLG),
Kahayan (KHY), dan Bukit tinggi (BGI) (Figure 3). Based on the results, there are three
land capability class in the upstream of Wampu Watershed, namely : land capability class
4
.
Figure 2. The location of the study on the Langkat administration
5
Figure 4. Map of land capability in the upstream of Wampu Watershed
The land with class III has a flat slope level, the land cover class III are in the
wetland and dry farming with area 919.77 ha, land capability classification results
were agree with the statement of Wirosuprojo (2005) which states that based on the
landform and direction of land use, it can be explained that the area has a flat and
gentle slopes with fertile soil and sufficient water available continuously an
agricultural area of wetlands that can be established as a center for food crops. wetland
and dry farming classified into class III was also agree with the statement of Arsyad
(2006) which states that the land belonging to class III is a land that has a formidable
barriers that reduce the choice of the use or require special conservation measures and
both. The land with Class III can be used for crops and plants that require tillage, grass
crops, pasture, forest production, forest and wildlife reserves. It is also supported by
Fletcher and Gibb (1990) which states that the land capability class I-IV can be used
for fields and intercropping.
The land with class V was covered by the dry agricultural land, fields,
settlements, and the plantation. The area was about 27 442.93 ha. According to
6
intercropping with soil conservation measures, the statement also was supported by
Arsyad (2006). In class V can only be used for grass, grazing meadow, forest
production or protection forest and nature reserves. According to Arsyad (2006) soils
in class V is not threatened land erosion but have other obstacles that are not to be
removed, limiting its use choice, because the land is suitable for grass crops, pasture,
and forest production or protection forest and nature reserves. Soils in class V have
barriers that restrict the use of a wide selection of plants and inhibit tillage for crops.
These soils located on flat or nearly flat topography but stagnant water, frequently
flooded or rocky or less appropriate climate or have a combination of these obstacles.
The land with class VI has a steep slope. The land was covered by the primary
forest, secondary forest and shrub with area abour 21.987.44 ha. This is agree with the
statement of Wirosuprojo (2005) which states that the steep slope areas should be used
for limited production forests, protected forests and nature reserves. Land cover
belonging to the class VI is also consistent with the statement Arsyad (2006) which
states that soils in class VI, the land is not suitable for agricultural use; its use was
limited to grazing, production forests, protected forests, and nature reserves. Class VI
soils located on moderate steep slope, if used for grazing and production forests should
be managed properly to avoid erosion. Some soils in class VI and roots in the area but
is located on moderate steep slope can be used for crops with severe conservation
measures. It is also supported by Rahmawaty (2011) which conducted research in
Besitang Watershed.
IV. CONCLUSIONS
Land capability classification in the upstream of Wampu Watershed consists
of three classes, namely: Class III , Class V and Class VI. Land capability
classifications according to land cover were in Class III and Class VI in the upstream
of Wampu Watershed. In class V, the suitable land covers were only on dry land
agriculture and plantations.
7
Arsyad, S. 2006. Soil and Water Conservation (
Konservasi Tanah dan Air
). Penerbit
IPB (IPB press), Bogor. 396p. [Bahasa Indonesia].
Fletcher, J.R.
and
R.G. Gibb. 1991.
Land Resource Inventory Handbook for Soil
Conservation Planning in Indonesia.
NZ DSIR Scientific Report No. 11. NZ
DSIR Land Resources and Dir Gen RLR of Indonesia. 87 pp.
Food and Agriculture Organization (FAO). 1976. A Framework for Land Evaluation.
FAO
Soils
bulletin
32,
Rome,
Italy.
http://www.fao.org/docrep/X5310E/x5310e00.htm#Contents
Oszaer, R. 1994. Land Use Optimization in Waeriuapa Watershed, Kairatu, Seram,
Maluku, Indonesia Using Geographical Information System and Linear
Programming. Ph.D. Dissertation. University of the Philippines Los Banos.
Rahmawaty, T.R. Villaneuva, M.G. Carandang. 2011. Participatory Land use
Allocation, Case Study In Besitang watershed, Langkat, North Sumatera,
Indonesia. Lambert Academic Publishing. German. 212pp.
Villanueva, T.R. 2005. Upland Ecosystem Management. Second Edition. University
of the Philippines Open University, Los Banos, Laguna. 200pp.
Wirosuprojo, S. 2005. Land
Classification for land use planning in Sleman district
Yogyakarta (
Klasifikasi lahan untuk perencanaan Penggunaan lahan di
kabupaten sleman Daerah istimewa Yogyakarta
). Fakultas Geografi UGM.
Yogyakarta.
[Bahasa Indonesia].
12/3/2018 Gmail - Fwd: IWoRS Schedule
https://mail.google.com/mail/u/1?ik=346879a4fa&view=pt&search=all&permthid=thread-f%3A1485883615552149021&simpl=msg-f%3A14858836155… 1/1 Rahmawaty PhD <[email protected]>
Fwd: IWoRS Schedule
1 message[email protected] <[email protected]> Thu, Nov 27, 2014 at 7:43 AM To: [email protected]
--- Original Message --- Subject: Fwd: IWoRS Schedule Date: 2014-10-15 09:02
From: "Int' Symposium of IWoRS 2014" <[email protected]>
To: mulyani efendi <[email protected]>, Achmad Solikhin <[email protected]>, [email protected], [email protected], [email protected], [email protected], [email protected], [email protected], Masturoh Surachman <[email protected]>, Ayu Asri <[email protected]>, [email protected], [email protected], ana agustina
<[email protected]>, [email protected], yosafat ap <[email protected]>,
[email protected], Detti Yunianti <[email protected]>, [email protected], Yudhi Dwi Kurniawan <[email protected]>, [email protected], [email protected], [email protected], [email protected], [email protected], [email protected], Agnes Sartika <[email protected]>, [email protected] , wahyu hidayat <[email protected]>, Yoichi Kojima <[email protected]>, enggar apriyanto
<[email protected]>, Asep Hidayat <[email protected]>, [email protected],
[email protected], benny safriani <[email protected]>, deded nawawi <[email protected]>, [email protected], [email protected], "Dr. Ir. Fahrizal, MP" <[email protected]>, [email protected], Ermy Puspita <[email protected]>, Seyed Eshagh Ebadi <[email protected]>, [email protected], Hikaru KOBORI <[email protected]>, Iwan Risnasari <[email protected]>, irawan
<[email protected]>, IMAM WAHYUDI <[email protected]>, Joko Sulistyo <[email protected]>, [email protected], [email protected], jmalik_2007 <[email protected]>, Dwi Kresnoadi <[email protected]>, [email protected], [email protected], muhdi syehamad
<[email protected]>, Titien mirza Titien <[email protected]>, momo subyakto
<[email protected]>, Maulida Oktaviani <[email protected]>, Nyoman Wistara <[email protected]>, Naresworo Nugroho <[email protected]>, Nurwati Hadjib
<[email protected]>, [email protected], winny - <[email protected]>, Rohny Maail <[email protected]>, [email protected], Satoshi NAKABA <[email protected]>,
SCHEDULE FOR INTERNATIONAL SYMPOSIUM OF INDONESIAN WOOD RESEARCH SOCIETY (IWoRS) GARUDA PLAZA HOTEL, 12-13 NOVEMBER 2014
Time Session
Kasuari Parkit Peakok Cendrawasih X
A.
Wood Based Properties
No
Code
The Title
1 A – 01 Samama (Anthocephallus macrophyllus) Wood Quality at 8 and 10 Years Old
Tekat Dwi Cahyono, Imam Wahyudi, Trisna Priadi, Fauzi Febrianto, Wayan Darmawan, Effendi Tri Bahtiar, and Syarif Ohorella
2 A – 02 Hyperspectral Imaging for The Knot Detection of Solid Wood Surface
Hikaru Kobori, Kouch Kato, Satoru Tsuchikawa, Yoichi Kojima and Shigehiko SuzukiI
3 A – 03 The Effects of Tar Treatment on Falcataria moluccana Wood Anatomical Properties Infected by Gall Rust Fungus
Hairi Cipta, Widyanto Dwi Nugroho, and Sri Rahayu
4 A – 04 Variations in Moisture Content and Shrinkage of Gigantochloa scortechinii and
Bambusa vulgaris at Different Height of Bamboo Culm
Rogerson Anokye, Regina Maria Kalong, Edi Suhaimi Bakar, Jegathewaran Ratnasingam, Mohammad Jawaid, and Khairul Awang
5 IS – A The Effect of Six Months Girdling on the Physical Properties of Teak Wood Growing on the Community Forest
Sri Nugroho Marsoem, Joko Sulistyo, Ganis Lukmandaru, Soekmana Wedatama, and Dwi Sukma Rini
6 A – 05 The Permeability of Some Tropical Hardwoods in Green and Dry Conditions
Adrian Choo Cheng Yong, Alinaghi Karimi, Paridah Md Tahir, Mohd Khairun
Anwar Uyub, and Edi Suhaimi Bakar
7 A - -06 Total Utilization of Oil Palm Stem
Wahyu Dwianto, Fitria, and Teguh Darmawan
8 A – 07 Characteristics Variation of Surian Woods (Toona Sinensis Roem.) in West Java, Indonesia
Yoyo Suhaya, Aos M. Akyas, Titin Supriatun, and Imam Wahyudi
9 A – 08 Differences in The Timing of Disappearance Among Cellular Contents During Cell Death of Ray Parenchyma in Abies sachalinensis
Satoshi Nakaba, Izumi Arakawa, Hikaru Morimoto Yuzou Sano, and Ryo Funada
10 A – 09 Effect of Heating Temperature on The Physical and Mechanical Properties of Okan Wood (Cylicodiscus gabunensis(Taub.) Harms)
Wahyu Hidayat, Jae-Hyuk Jang, Se-Hwi Park, and Nam-Hun Kim
11 A – 10 Characteristics of Several Wood from Community Forest as Potential Application for Raw Material for Composite Board
Andi Detti Yunianti, Suhasman, and Sahriyanti Saad
12 A – 11 Wood Anatomy and Related Properties of Naturally Grown Philippine Teak (Tectona philippinensis Benth. & Hook. f.)
B.
Biocomposite
No
Code
The Title
1 B – 01 Hot Pressing Behavior and Properties of Wood-Based Panels from Different Furnish and Various Densities
Muhammad Navis Rofii, Shuto Kubota, Yoichi Kojima and Shigehiko Suzuki
2 B – 02 Physical Mechanical Properties of Wood Plastic Composite Made from Recycled Plastic and Teak Sawdust Waste
N Hadjib, F Febrianto, YS Hadi
3 B – 03 Influence of Impact Modifier-Compatiblilizer Combination on Tensile Properties and Impact Strength of Wood Flour and Polypropylene Composite
Fauzi Febrianto, Seung-Hwan Lee, Wahyu Hidayat, I Nyoman Jaya Wistara, Nam-Hun Kim
4 B – 04 Properties Of Sengon Particleboards Bonded Using Citric Acid and Sucrose as Natural Binders
Ragil Widyorini and Pradana Ardhi Nugraha
5 IS B The Effect of Supercritical CO2 Treatment on The Curing and Degradation
Processes Of Cement-Bonded Particleboard
Rohny S. Maail, Kenji Umemura, Hideo Aizawa, and Shuichi Kawai
13 A – 12 Variation in Mechanical Properties of Two Rubberwood Clones in Relation to Planting Density
Hamid Reza Naji, Edi Suhaimi Bakar, Hazandy Abdul-Hamid, Seyed Eshagh Ebadi, and Mohd. Hamami Sahri
14 A – 13 Wood Properties of Shorea agamii P.S. Ashton and Its Potential Utilization as an Alternative for Pulp and Paper Raw Material
Listya Mustika Dewi, Dian Anggraini Indrawan, and Han Roliadi
15 A – 14 Bond Ability of Oil Palm Wood with Isocyanate Adhesive
Atmawi Darwis, Muhammad Y Massijaya, Naresworo Nugroho, Eka M Alamsyah, and Dodik R Nurrochmat
16 A – 15 Suitability of The 28 Year-Old of Conventional Teakwood as Raw Material for Wooden Furniture
Imam Wahyudi, Yusuf Zawawi, and Armita Prilia Nestri
17 A – 16 Wood Properties of Kayu Bawang Planted in South Sumatera, Indonesia
Haruna Aiso, Mirai Hirano, Futoshi Ishiguri, Ridwan Yahya, Imam Wahyudi, Jyunichi Ohshima, Kazuya Iizuka, and Shinso Yokota
18 A – 17 Physico-mechanical Behaviors of Heat Treated Oil Palm Wood in Different Buffered Mediums
6 B – 05 Cyclic Test on Jatropha Hulls Particle Board with Urea Formaldehyde Adhesive and Soaking Treatment
Ana Agustina and Dede Hermawan
7 B – 06 Mechanical Properties of Composite Based on Polylactic Acid and Kraft Pulp of Oil Palm Empty Fruit Bunch
Lisman Suryanegara and Yudhi Dwi Kurniawan
8 B – 07 Effect of Wood Shaving Mixture to Improve Mechanichal Properties of Particleboard Made from Sorghum Stalk Bagasse
Apri Heri Iswanto, Irawati Azhar, Supriyanto, and Andriyanta Ginting
9 B – 08 Improvement of PVA Composite Film Properties by Reinforcing Nanocrystalline Cellulose Isolated from Primary Sludge
Iwan Risnasari, Fauzi Febrianto, Nyoman Jaya Wistara, Sucahyo Sadiyo and Siti Nikmatin
10 B – 09 The Substitution Effect of Oil Palm Shell Charcoal, Coconut Fiberand Empty Fruit Bunched Fiber for Physical and Mechanical Properties of Composite for Railway Brake Blocks
Ismail Budiman, Ismadi, Subyakto, Sasa Sofyan Munawar, Wida Banar Kusumaningrum, Hilman Saeful Alam, Agus Edy Pramono, and Jayadi
11 B – 10 Particleboard with Jatropha Hulls Treatment Soaking as Efforts to Improvement The Product Quality
Dede Hermawan and Ana Agustina
12 B – 11 Effects of Fiber Loading on The Properties of Pineapple Leaves Fiber – PLA Nanocomposites
Subyakto, Lisman Suryanegara, Wida Banar Kusumaningrum, Yudhi Dwi Kurniawan
13 B – 12 Fibrillated Oil Palm Frond Cellulose Fibers in Polylactic Acid-Polypropylene Blends Composite
Firda Aulya Syamani, Subyakto, Sukardi, and Ani Suryani
14 B – 13 Effect of Rubber and Falcata Ratio to Strandboard Manufacture
IhakSumardi ,EkaMulya Alamsyah, and Atmawi Darwis
15 B – 14 Surian Bark-Powder as a New Alternative for The Decreasing of Pressure Temperature of Phenol Formaldehyde (I): Plywood Production
Eka Mulya Alamsyah, Sutrisno and Tati Karliati
16 B – 15 Particleboard from Fast Growing Species with an Extract Bark of Mahogany (Swietenia sp) as Tannin Adhesive
Andi Sri Rahayu Diza Lestari, Yusuf Sudo Hadi, Dede Hermawan, and Adi Santoso
17 B – 16 Effects of Density and Resin Level on the Permeability and Water Absorption of Kenaf-Rubberwood Particleboard
18 B – 17 Effect of Layers Structure on Characteristics of Binderless Comply
Suhasman, Andi Detti Yunianti, and Sahriyanti Saad
19 B – 18 Utilizitation of Co2 Injection Technology and Acccelerator for Producing Bamboo
Cement Board
Bakri, Musrizal Muin, Baharuddin, Sahriyanti Saad, and Suhasman
20 B – 19 Utilization of Cardboard Duplex as an Alternative Raw Materials Composite Board
Nova Lestari and Muh. Yusram Massijaya
21 B – 20 Mechanical Properties 3-Ply Plywood of Paraserianthes mollucana Using Three Diferrent Adhesive
Mulyani Efendi and Yusram Massijaya
22 B – 21 Morphological Characteristics of Lignocellulose Nanofibers Prepared by Enzymatic Hydrolysis from Different Lignin Content of Betung Bamboo
Jae-Hyuk Jang, Noriko Hayashi, Seung-Hwan Lee, Eiji Togawa, Satoshi Kubo, Fauzi Febrianto and Nam-Hun Kim
23 B – 22 Nano Clay and Phenolic Resin Admixture as Novel Bulking Agent for Lignocellulosic Materials
Nabil Fikri Leemon, Zaidon Ashaari, Mohd Khairun Anwar Uyup, Edi Suhaimi Bakar, Paridah Md Tahir, Mohd Anuar Ridzuan Saliman and Mohd Aizat Ghani
24 B – 23 Performance Measurements of Oil Palm Stem Plywood as Potential Raw Material in Certified Plywood Production Using Property-Cost Index (PCI)
Aida Adnan, Paridah Md. Tahir, Khamuruddin Mohd. Nor, and Rosli Saleh
C.
Wood Quality, Laminated Board and Wood Engineering
No
Code
The Title
1 C – 01 The Quality of Jabon Wood Impregnated with Styrene and Methacrylathe
Lusita Wardani, Iwan Risnasari, Yusuf Sudo Hadi
2 C – 02 New Efficient and Practical Method for Producing „Compreg‟ OPW through Integrated Objective Approach
Edi S. Bakar, Al-Hasan Y. Abare,Adrain C.C. Yong,Zaidon Ashaari
3 C – 03 Effect of Steaming before Compression on The Physico-Mechanical Properties of
Compreg OPW Treated with the 6-step Processing Method
Alhassan Y. Abare,Edi S. Bakar,and Zaidon Ashaari
4 C – 04 Physical Mechanical Properties of Poly Ethylene Glicol Wood From Three Fast Growing Species
5 IS – C Substituting Modulus of Elasticity Ratio by Vascular Bundle Ratio for Bamboo Strip and Laminated Bamboo Layer System Analysis
Naresworo Nugroho, Effendi Tri Bahtiar, Surjono Surjokusumo, Lina Karlinasari, Atmawi Darwis
6 C – 05 Effect of Impregnation with Polymerized Merbau Extractive on the Fixation of Compressed White JabonWood (Anthocephalus Cadamba)
Jamaludin Malik, Barbara Ozarska, Wahyu Dwianto, Yan Mulyana, Gustan Pari, and Dede Hermawan
7 C – 06 Physical Mechanical Properties of Poly Ethylene Glicol and Polystyrene Woods from Mangium and Pine
Masturoh Surachman, Yusuf Sudo Hadi,and Dominicus Martono
8 C – 07 Physical Mechanical Properties of Polystyrene Wood of Three Fast Growing Species
Aji Kusumo Wibowo, Yusuf Sudo Hadi, and Nurwati Hadjib
9 C – 08 Shear Strength Quality Of Red Meranti Gluelam
IsnaYuniar Wardhani and AgusSulistyo Budi
10 C – 09 Physical-Mechanical Properties of Glued Laminated Timber Made from Small-Diameter Log
Rahma Nur Komariah, Yusuf Sudo Hadi, Muh.Yusram Massijaya, and Jajang Suryana
11 C -10 Microwave and Steam Injection Drying of Laser Incised Mahogani Lumber
Tomy Listyanto,Keisuke Ando, Hidefumi Yamauchi, Nobuaki Hattori
12 C -11 Performance of Laminated Wood Glued with Gutta-Percha-based Adhesive
Tati Karliati, Fauzi Febrianto, Wasrin Syafii , Imam Wahyudi
13 C – 12 Performance Of Glued Laminated Lumber Made From Waste Oil Palm Trunk
Dina Ali, Muh. Yusram Massijaya, Yusuf Sudo Hadi
14 C – 13 Lathe Check Characteristics of Fast Growing Sengon Veneers and Their Effect on LVL Glue-Bond and Bending Strength
Wayan Darmawan, Dodi Nandika, Irsan Alipraja, Abigael Kabe, Istie Rahayu, Louis Denaud, and Barbara Ozarska
15 C – 14 Physical and Mechanical Properties of Laminated Board made from Bamboo Betung (Dendrocalamus asper Backer Ex. Heyne) Under Various Treatment of Layers Number and Testing Position
Mariah Ulfa, Luthfi Hakim, Tito Sucipto
16 C – 15 Cross Laminated Timber Made From Fast Growing Species With Acacia Tannin Adhesive
Jessica, Yusuf Sudo Hadi, Muh. Yusram Massijaya,Adi Santoso
17 C – 16 The Effect Of Finger Joint Orientation And Teak Quality Class On Its Adhesion Strength
18 C – 17 Glulam timber beam-column joint using quick connect system
Johannes Adhijoso Tjondro, Pricillia Sofyan Tanuwijaya
19 C – 18 Development of Lateral Load Connections with Modified-Washer and Nail
Strengthening
Y.A. Pranata, A. Kristianto, and O.C. Pattipawaej
20 C – 19 Application of Non-Destructive Test for Checking Available Timber for Construction Materials in the Market
Ajun Hariono and Anita Firmanti
21 C – 20 Building Condition Index And Remaining Service Lifetime Estimation For Wood Component Of Low Cost House At Alam Sinar Sari – Bogor
Effendi Tri Bahtiar, Arinana, Naresworo Nugroho, Dodi Nandika, dan Muhamad Ari Kurniawan
22 C – 21 The Effect of Radial Position and Veneer Thickness on Mechanical Properties of Fast Growing Species Laminated Veneer Lumber
Istie Rahayu, Louis Denaud, Julien Ruelle, Wayan Darmawan
23 C – 22 Effect of Knives Speed Rotation and Duration of It‟s Use on Machining Quality of Teak Wood
Yustinus Suranto and Sigit Pambudi
24 C – 23 Development and Characterization of Finger-jointed Laminated Bamboo Timber for Furniture application
Rogerson Anokye, Edi Suhaimi Bakar, Jegathewaran Ratnasingam, Mohammad Jawaid, Khairul Awang
D.
Wood Biodegradation and Non Wood Forest Product
No
Code
The Title
1 D – 01 Comparing The Potential Ability of Fungi Isolated from Tropical and Temperate Forest, to Decolorize Four Type Dyes
Asep Hidayat and Sanro Tachibana
2 D – 02 The Resistance from Dry Wood Termite (Cryptotermes cynocephalus) after Heat Treatment of Mindi Wood (Melia azedarach L.).
Trisna Priadi, and Ady Pratama
3 D – 03 The Treatability of Anggrung (Trema orientalis) Wood by Copper Sulfate
Taman Alex
4 D – 04 Termite Resistance of Three Layer Particle Board Shorea Leprosula Miq. from Natural and Plantation Forest
5 IS – D Consumtion Rate and Transfer Efficiency by Termite Coptotermes sp. of Organic Waste-based Food for Bait Formulations
Musrizal Muin, Astuti Arif, Sitti Nuraeni, Heru Arisandi dan Wa Ode Fatima Zahro
6 D – 05 Evaluating The Adhesion Durability of API Bonded Glulam after The Accelerated Aging Treatments
Taiyo Okada, Hikaru Kobori, Yoichi Kojima, Shigehiko Suzuki, Kuniharu Nishikido, Akira Hirose, Kazuaki Takahashi
7 D – 06 Detection of Incipient Decay of Meranti Wood by Using Light Microscope
Erwin, Dady Mulya, and Agus Sulistyobudi
8 D – 07 Antioxidant and Antimicrobial Activities of Several Plants from Sapindaceae Families
Whicliffe Fiernaleonardo Pasedan, and Harlinda Kuspradini
9 D – 08 Termite Species Diversity and Intensity of Building Damage in Perumahan Nasional Bumi Bekasi Baru-Rawalumbu-Bekasi
Arinana, Noor Farikhah Haneda, and Windi Ayu Prawitasari
10 D – 09 Potenctial of Lai fruit (Durio kutejensis) Extract as an Antioxidant and Anti-Melanogenesis Activities
Enos Tangke Arung, Wiwin Suwinarti, Medi Hendra, Supomo, Irawan Wijaya Kusuma, Dwi Caesarina Nanda Puteri, Kuniyoshi Shimizu, and Hiroya Ishikawa
11 D -10 Distribution and Identification of The Termite Genus Coptotermes in South Sulawesi, Indonesia
Astuti Arif, Musrizal Muin, Nurariaty Agus, and Muh. Nasrum Massi
12 D -11 Durability of Cross Laminated Timber From The Palm Oil Trunks ( Elaeis guineensis Jacq ) on Various Orientation Fiber
Dwi Hatmojo Kresnoadi and Muh. Yusram Massijaya
13 D– 12 Durability of Several Densified Woods
Imam Wahyudi and Novan Danuwihardi
14 D – 13 Termite Pests (Isoptera: Kalotermitidae, Rhinotermitidae, and Termitidae) in Bandung City
Eko Kuswanto, Intan Ahmad, Ramadhani E. Putra, and Idham S. Harahap
15 D – 14 Treatability of Oil Palm Frond and Rubberwood Chips with Urea for The Development of Slow Release Fertilizer
Nur Nabilah AK, Zaidon Ashaari, Ahmad Husni M H, Azmy M and Lee, S H.
16 D – 15 Natural Durability and Effectiveness of Boron Compound as Preservatives in Teak Wood from Short Rotation Community Forest
Yus Andhini Bhekti Pertiwi, Sri Nugroho Marsoem, and Joko Sulistyo
17 D – 16 Enzymatic Delignification Of Falcata (Paraserianthes falcataria) Wood By White Rot Fungi Trametes versicolor
E.
Wood Chemistry and Bioenergi
No
Code
The Title
1 E – 01 Methane Production from Co-Digestion of Palm Oil Mill Effluent (POME) and Shredded Empty Fruit Bunches (EFB)
Nurliyana M.Y., H’ng P.S., Halis R., and Umi Kalsom M.S
2 E – 02 Quality Traits of Leaf Bleached Kraft Pulp (LBKP) of Local Wood Species, Terentang and Binuang
Eka Novriyanti, Dodi Frianto, and Ahmad Rojidin
3 E – 03 Bond Quality of Aqueous Polymer Isocyanate Adhesive Prepared from Natural Rubber Latex, Lignin and Polyvinyl Alcohol with Isocyanate Crosslinker
Euis Hermiati, R. Permana Budi Laksana, M. Adly Rahandi Lubis, Lucky Risanto, Rusli
4 E – 04 The Utilization of Lignocellulose Biomass from Plantation Forest as Raw Material for Bioethanol Production
Wiwin Suwinarti, Rudianto Amirta and Wahyu Kurniawan
5 IS – E Evaluation of growth and potential ethanolproduction from Macaranga gigantea, an alternative plant species for the development of forest energy plantation in Indonesia
Rudianto Amirta, Dwi Susanto, Maman Sutisna and Daddy Ruchyat
6 E – 05 Utilization of Adsorbent from Tamarind Seeds for the Reduction of PV (Peroxide Value) in CPO (Crude Palm Oil)
Agnes Sartika Pardede, Agus Mangiring Siburian and Setiaty Pandia
7 E – 06 Quality Of Biopellets From Oilpalm Trunk And Rice Husk With Different Type Of Adhesives
Dina Setyawati, Farah Diba, and Nurhaida
8 E – 07 Torrefaction for upgrading the calorific value of wood waste of Melia azedarach L.
for heating material
J.P. Gentur Sutapa, Aji Nur Rakmat and Denny Irawati
9 E – 08 Fiber Disruption Of Betung Bamboo (Dendrocalamus Asper) By Combined Fungal And Microwave Pretreatment
Widya Fatriasari, Wasrin Syafii, Nyoman Wistara, Kaswar Syamsu, Bambang Prasetya, Sita Heris Anita, and Lucky Risanto
10 E – 09 Utilization of Oil Palm Waste (ElaeisguineensisJacq.) as Biopellet Materials
Wihdatul A. Sa’adah, Muh. Yusram Massijaya, and GustanPari
11 E – 10 Characteristics of Biopelet from Mixed of Shells and Frond of Oil Palm (Elaeis guineensis Jacq.)
12 E – 11 Palm Shells and Empty Fruit Bunches Biopellet as an Alternative Renewable Energy Resource
Novi Ari Christanty, Dede Hermawan and Gustan Pari
13 E – 12 Removal of Oil Palm Biomass Ash Forming Elements Using Leaching Techniques
K.L. Chin, P.S. H’ng, S.H. Lee, W.C. Lum, M.T. Paridah, A.C. Luqman, and M. Maminski
14 E – 13 The Properties of Biopellet from Oil Palm Trunk
Nyoman J Wistara, Mohammad A Rohmatullah, and Gustan Pari
15 E – 14 Chemical and Morphological Change of Empty Palm Fruit Bunch Fibers Pretreated by Hot Treatment and Three White-Rot Fungi for Obtaining Ultralong Cellulose Nanofibers (CNFs)
Achmad Solikhin, Yusuf Sudo Hadi, Muh. Yusram Massijaya, and Siti Nikmatin
16 E – 15 Potential of a Medicinal Plant from Bentian Tribe, Kaser (Cananga sp) as a Source of Pharmacologically Active Compound
Anindya Marsabella Rosiarto, Irawan Wijaya Kusuma, Murdiyanto, Farida Aryani, Enos Tangke Arung, Yong-Ung Kim
17 E – 16 Biological Activities of Ethnobotanically-Selected Medicinal Plants In East Kalimantan Local Tribes
Irawan Wijaya Kusuma, Murdiyanto, Farida Aryani, EnosTangke Arung, Syafrizal, Yong-Ung Kim
18 E – 17 A Study of Antibacterial Effect of Some Selected Essential Oils from Lauraceae Plants
Harlinda Kuspradini, Dewi Ardiana Putri, and Yanti
F.
General Forester
No
Code
The Title
1 F – 01 Growth Evaluation of Ebony (Diospyros Ebenum Koenig.) for 22nd Month Age in
Arboretum of Manado Forestry Research Institute
Julianus Kinho
2 F – 02 The Potency of Indigenous Species as A Mercury Phytoremediator on Illegal Ex-Gold Mining Reclamation
Wiwik Ekyastuti and Emi Roslinda
3 F – 03 Drainage Ditches Establishment on Peatland Landscape: Effects on Water Table Levels, Biomass Growth, and Mortality of West Kalimantan Degraded Forests
4 F – 04 Analysis of Multistakeholders in Rattan Industry Development in Ambon City
Messalina L Salampessy , Indra G Febriano, Buchkori,and Neni
5 IS – F Bridging the Network on Research of Restoration Forest Ecosystem Based on Community as an Efforts to Reduce Green Houses Gases Effect
Gusti Hardiansyah, Fahrizal, and Farah Diba
6 F – 05 An Optimum Choice of Strategic Marketing for Indonesian Plywood Industry: Operationalization of Porter Five Forces Model using Analytic Hierarchy Process
Makkarennu, Akira Nakayasu, Katsuya Osozawa, and Masahiro Ichikawa
7 F – 06 Semi-Manual Technique of Mangrove Commercial Exploitationat Bintuni Bay, West Papua
Wahyudi
8 F – 07 The Economic Impact of Sustainable Forest Management (SFM) Practices on The Development of Plywood Market in Peninsular Malaysia
A.W. Noraida, A.S. Abdul Rahim and H.O. Shahwahid
9 F – 08 The Content Of Heavy Metal Lead (Pb) in The Dragon Fruit and Cassava on Coal Mined Lands In the Village Of Purwajaya Tenggarong District East Kalimantan
Budi Winarni, Nur Hidayat, Sri Ngapiyatun
10 F – 09 Carbon Stock Estimation on Some Trees in Ecological Corridor between Betung Kerihun and Kayang Mentarang National Park, East Kalimantan
Rita Diana
11 F – 10 Mined-out Land Rehabilitation Works and it‟s Potential Recovery - A Field Observation and Research Experience
Triyono Sudarmadji
12 F – 11 Genetic Quality of P. falcataria (L) Nielsen Half-Sib Progeny Test F-2 Followed of Stem Borrer Resistance and High Economic Selection Base on Morphology Marker
Sopandi Sunarya and Susana P Dewi
13 F – 12 Ecological Preference of Litsea cubeba Lour. Persoon in Mount Papandayan: Relationship to Essential Oil Yield and Compositions
Ichsan Suwandhi, Cecep Kusmana, Ani Suryani, and Tatang Tiryana
14 F – 13 Breadfruit (Artocarpus Communis Forst) Seedling Growth Response to Some Kind of Watering to Soil Derived from The Catchment Area of Lake Toba
Afiffuddin Dalimunthe, Budi Utomo, Irma Y Sembiring
15 F – 14 Analysis of Production Cost of Carbonless Copy Paper (Case Study in PT. Pindo Deli Pulp and Paper Mills II)
Ratih Ayu Syafriza and E.G. Manurung
16 F – 15 Analysis of Potency and Quality of Elaeis Guineensis Oils in Bangun Bandar Seed Production, North Sumatra, Indonesia
17 F – 16 Carbon Storage and Spatial Distribution of Hybrid Eucalyptus Plantation Forest
Siti Latifah
18 F – 17 Land Capability Classification at Wampu Hulu Sub Watershed Langkat North Sumatra Using Geographic Information System
Rahmawaty, Sari Adryana, Ahmad Syofyan, and Abdul Rauf
19 F – 18 Land Use Changes and Impact of Forest Disturbances on Human Wildlife Conflict
in Sumatera
Pindi Patana, Ma’rifatin Zahra
20 F – 19 Production and Palatability of Plant Feed of Sumatran Elephant (Elephas Maximus Sumatranus) in Pinus Nature Reserve Jantho, Aceh
Ma’rifatin Zahrah and Retno Widhiastuti
21 F – 20 Studies on Air Pollution Tolerance Index of Selected Plants Around Industrial Zone in Bontang, Indonesia
Benny Safriani, Ichrar Asbar, and Irawan Wijaya Kusuma
22 F – 21 The Effect of Skidding to Soil Porosity by Reduced Impact Logging at Natural Tropical Forest, North Kalimantan, Indonesia
Muhdi
23 F – 22 The Diversity of Forage Plant and Honey Yield of Apis Cerana in Simalungun Regency
Dwi Endah Widyastuti, Darma Bakti Nasution, Sutarman
G. Poster
No
Code
The Title
1 G - 01 Characteristics of Tropical Woods Lignin and Its Reactivity in Alkaline Delignification
Deded Sarip Nawawi, Anne Carolina, Nyoman J Wistara
2 G - 02 Evaluation of binding effects in wood flour board containing ligno-cellulose nanofibers
Yoichi Kojima, Hikaru Kobori, Shigehiko Suzuki, Hirokazu Ito, Rie Makise, Masaki Okamoto
3 G - 03 Physical and Mechanical Properties of Platinum Teak Wood
Danang Sudarwoko Adi, Sudarmanto, Ismadi, M. Gopar, Wahyu Dwianto
4 G - 04 Anatomical Properties and Fiber Characteristics of Platinum Teak Wood as a New Promising Teak Wood from LIPI
5 G - 05 Physical and mechanical properties of Hwangjangmok (Yellow-hearted pine)
Ae-Hee Lee, Jae-Hyuk Jang, Se-Hwi Park and Nam-Hun Kim
6 G - 06 Fine fibrosis characteristics of four tropical woods for nanocellulose production
Wahyu Hidayat, Jae-Hyuk Jang, Sa-Ra Jang, Se-Hwi Park, Fauzi Febrianto and Nam-Hun Kim
7 G - 07 Chemical Composition and Color Variation of Platinum Teak Wood - a Fast Growing Teak Wood from LIPI
Danang Sudarwoko Adi, Ika Wahyuni, Dwi Ajias P, Yusup Amin, Teguh Darmawan, Wahyu Dwianto
8 G - 08 Wood Properties of Shorea almon and Its Suitability for Furniture
Listya Mustika Dewi, Sri Rulliaty, Abdurachman, Jasni
9 G - 01 Mechanical Characteristic of Coconut and Oil Palm Empty Fruit Brunch Fiber Based Composites With Soaking Treatment In Vertical Garden Board Application
M. Gopar and Ismadi
10 G - 10 Mechanical Characteristic of Coconut Fiber Based Composites With Time Watering Variation In Vertical Garden Board Application
Ismadi and M. Gopar
11 G - 11 The Possibility Of Oxidation Treatment Application In Manufacturing Binderless Particleboard Using Severeal Wood Species From Community Forest
Suhasman, Andi Detti Yunianti, Sahriyanti Saad
12 G - 12 Chemical Analysis of the Essential Oil Constituents in the Leaves of Pogostemon sp from Different Place in East Kalimantan
Harlinda Kuspradini, Farida Aryani and Yanti
13 G - 13 Morphology and Physical Characteristics of Polypropylene-Pulped Empty Fruit Bunch Fiber Composites with Chitosan as Filler
Kurnia Wiji Prasetiyo and Lisman Suryanegara
14 G - 14 Ethanol Production from Alkali-Pretreated Sugarcane Bagasse via Simultaneous Saccharification and Fermentation
Maulida Oktaviani, Triyani Fajriutami, Euis Hermiati
15 G - 15 The Utilization Development Of Solid Wood Materials On Design Of Traditional House
James Rilatupa
16 G - 16 Effect Of Acetylated Cellulose From Empty Fruit Bunch Pulp On Mechanical Properties Of Polypropylene Composites
Wida B.Kusumaningrum*, Kurnia Wiji Prasetyo, Firda A.Syamani
17 G - 17 An Improved Process for Isolating Lignins from Sugarcane Bagasse
18 G - 18 Local scale of Primary Wood Processing EntrepreneurshipatManokwari town, West Papua
Wahyudi, H.F. Kawet, M. Arifudin, M. Totong, and B.B. Rettob
19 G - 19 “Arang” Wood (Diospyros maritime (?) sp) as Subsitution of Eboni Wood (Diospyros celebica)
Andi Detti Yunianti
20 G - 20 Radial variation of fiber anatomical features, wood density, and chemical constituents in Acervelutinum
Seyed Eshagh Ebadi, Hamid Reza Naji, Hazandy Abdul-Hamid, Mojtaba Soltani
21 G - 21 The Effect Of Moisture Content And Water Cement Ratio On Manufacturing Cement-Bonded Particleboard By Using Supercritical CO2
Rohny S. Maail, Kenji Umemura, Hideo Aizawa, Shuichi Kawai
22 G - 22 Changes in cellular contents of ray parenchyma cells during heartwood formation in Cryptomeria japonica
Izumi Arakawa, Hikaru Morimoto, Ryogo Nakada, Ryo Funada & Satoshi Nakaba
23 G - 23 Production of Sodium Lignosulfonate from Lignin Derived from Sugarcane Bagasse Pretreatment
Fitria, Triyani Fajriutami, Widya Fatriasari, Faizatul Falah and Euis Hermiati
24 G - 24 Variation Surface Layer and Glue Spread on Laminated Board With Core of Oil Palm Trunk
Rudi Hartono, Tito Sucipto, Rahmat Hidayat, David Pangihutan Pasaribu, Wahyu Dwianto
25 G - 25 Effect Of Salt Concentration On Growth Of Six Mangrove Seedlings And Their Association To Habitat Zonation
