Document details
13 of 28
Design and Simulation of Fuzzy Logic Based Temperature Control for a Mixing Process in Therapeutic Pool
(Conference Paper) (Open Access), , , , , ,
Dept. of Mechanical Engineering, Diponegoro University, Tembalang, Semarang, 50275, Indonesia Garuda Maintenance Facility AeroAsia, Soekarno Hatta International Airport, Cengkareng, Indonesia Dept. of Public Health and Preventive Medicine, Diponegoro University, Semarang, Indonesia
Abstract
Stroke is one cause of the most deaths, in which one way of handling stroke can be done with hydrotherapy.
Hydrotherapy is a therapy that is done in the therapeutic pool which is filled with warm water in temperature 31°-34° C. When in the warm water, body burden becomes lighter, so the stroke patients with impaired movement of the body can train the nerves and muscles in order to restore the function of these organs. However, the warm water that is used for the therapy is produced by the heater that requires much electrical energy. This research discussed how to use solar energy to produce hot water using Indirect Evacuated Tube Solar Water Heater systems and make the control system for controlling the mixing process between the hot and cold water by using the Fuzzy Logic Control of the Mamdani method. Therapeutic pool system will be modeled using Simulink. Modeling the mixing process is made on the basis of mass balance and energy balance equations. Then the system will be simulated with interrupted condition and gets set value changes in a particular time. The FLC is successfully reached and maintained steady to a set value. The results will be compared to the performance of the one with Proportional Integral Derivative controller. © The Authors, published by EDP Sciences, 2018.
SciVal Topic Prominence
Topic:
Prominence percentile: 85.671
Indexed keywords
Engineering controlled terms:
Computer circuits Fuzzy logic Lakes Mixing Patient treatment Physical therapy Proportional control systems Solar energy Two term control systems
◅ Back to results ◅ Previous Next ▻
Export Download Print E-mail Save to PDF ⋆ Add to List More...▻
View at Publisher
MATEC Web of Conferences
Volume 159, 30 March 2018, Article number 02039
2nd International Joint Conference on Advanced Engineering and Technology, IJCAET 2017 and International Symposium on Advanced Mechanical and Power Engineering, ISAMPE 2017; Bali;
Indonesia; 24 August 2017 through 26 August 2017; Code 135617
Munadia Ramadhan, E.F.a Ariyanto, M.a Iskandar, N.a Amirullah, M.A.b Julianti, H.P.c Setiawan, R.d
a b c
View additional affiliations
View references (11)
Air conditioning | Thermal comfort | Cabin temperature
PlumX Metrics Usage, Captures, Mentions, Social Media and Citations beyond Scopus.
Metrics
2
Citations in Scopus90th percentile
2.42
Field-Weighted Citation ImpactCited by 2 documents
, ,
(2019) IOP Conference Series:
Earth and Environmental Science
, ,
(2019) IOP Conference Series:
Earth and Environmental Science
Inform me when this document is cited in Scopus:
Related documents
, ,
❓ View all metrics ▻
Assembling fixed wing UAV for the low-cost aerial mapping Tobing, F.M. Yuwono Handoko, E.Y.
Idenfication of Factors for Assessing Regional Readiness Level in Disaster Management in Sleman Regency
Handayani, N.U. Sari, D.P.
Nugroho, A.S.
View all 2 citing documents
Set citation alert ▻ ▻ Set citation feed
Sliding mode control for therapeutic pool model control system
Munadi Kristianto, H. Ariyanto, M.
Brought to you by
Universitas Diponegoro
Search Sources Lists SciVal ↗ Create account Sign in
References (11)
Engineering uncontrolled terms
Design and simulation Electrical energy Energy balance equations Evacuated tubes Fuzzy logic control Proportional integral derivative controllers Stroke patients Therapeutic pool
Engineering main heading:
Process control
Zeghoudi, A., Chermitti, A.
A comparison between a fuzzy and PID controller for universal motor
(2014) International Journal of Computer Applications, 104 (6), pp. 32-36. .
Munadi, Naniwa, T.
(2013) Journal of Robotics and Mechatronics, 25 (4), pp. 737-747. .
Munadi, Akbar, M.A.
(2014) Proceedings of 2014 International Conference on Intelligent Autonomous Agents, Networks and Systems, INAGENTSYS 2014, art. no. 7005725, pp. 42-46. .
ISBN: 978-147994802-4
doi: 10.1109/INAGENTSYS.2014.7005723
Emilian, S., Dulau, O.M.
Design and simulation of fuzzy logic based temprature control for a plasma nitriding process (2015) Procedia Technology, 19, pp. 569-575. .
(2016) Compact Solar Water Heater Solartubes, Accessed on Mei 3rd 2016
ISSN: 2261236X
Source Type: Conference Proceeding Original language: English
DOI: 10.1051/matecconf/201815902039 Document Type: Conference Paper
Volume Editors: Setiawan J.D.,Hatmoko J.U.D.,Kurdi O.,Setiadji B.H.,Widodo A.,Han A.L.
Sponsors:
Publisher: EDP Sciences
▻ View in search results format All Export Print E-mail Save to PDF Create bibliography
1
Cited 3 times
2
Experimental verification of adaptive dominant type hybrid adaptive and learning controller for trajectory tracking of robot manipulators
Cited 10 times http://www.fujipress.jp/finder/access_check.php?
pdf_filename=ROBOT002500040020.pdf&frompage=abst_page&errormode=Login&pid=4811&lang=English View at Publisher
3
Simulation of fuzzy logic control for DC servo motor using Arduino based on MATLAB/Simulink
Cited 27 times
View at Publisher
4
Cited 4 times
5
www.solartubs.com
(2017) Proceedings - 2016 3rd International Conference on Information Technology, Computer, and Electrical Engineering, ICITACEE 2016
, ,
(2017) Proceedings - 2016 6th International Annual Engineering Seminar, InAES 2016
, ,
(2018) International Journal of Mechanical Engineering and Technology
Find more related documents in Scopus based on:
Model Reference Adaptive Control for DC motor based on Simulink
Munadi Akbar, M.A. Naniwa, T.
L1 adaptive control for missile longitudinal dynamic using MATLAB/Simulink Munadi, M. Ariyanto, M.
Setiawan, J.D.
View all related documents based on references
▻
Authors Keywords ▻
13 of 28 Siegfried, R., Mayer, D.
(2005) Ethylene Glycol, Ullmann's Encyclopedia of Industrial Chemistry, 12, p. 532.
(2016) Ethylene Glycol Heat-Transfer Fluid Engineering Toolbox, Accessed on May 4th
Cengel, Y.A.
(2002) Heat Transfer: A Practical Approach, pp. 463-469. . 2nd ed, Mcgraw-Hill
Rezeka, S.F., Attia, A.-H., Saleh, A.M.
(Open Access)
(2015) Alexandria Engineering Journal, 54 (2), pp. 91-98. . doi: 10.1016/j.aej.2015.03.014
Mendel, J.M.
(1995) Proceedings of the IEEE, 83 (3), pp. 345-377. . doi: 10.1109/5.364485
Lameres, B.J., Nehrir, M.H., Gerez, V.
(1999) Electric Power Systems Research, 52 (3), pp. 267-271. . doi: 10.1016/S0378-7796(99)00022-X
Munadi, ; Dept. of Mechanical Engineering, Diponegoro University, Tembalang, Semarang, Indonesia;
email:
© Copyright 2018 Elsevier B.V., All rights reserved.
6
7
www.engineeringtoolbox.com
8
Cited 2016 times
9
Management of air-conditioning systems in residential buildings by using fuzzy logic
Cited 9 times
http://www.elsevier.com/wps/find/journaldescription.cws_home/724292/description#description
View at Publisher
10
Fuzzy Logic Systems for Engineering: A Tutorial
Cited 1262 times
View at Publisher
11
Controlling the average residential electric water heater power demand using fuzzy logic
Cited 16 times
View at Publisher
munady096@gmail.com
◅ Back to results ◅ Previous Next ▻ Top of page
About Scopus
What is Scopus Content coverage Scopus blog Scopus API Privacy matters
Language
⽇本語に切り替える 切换到简体中文 切換到繁體中文 Русский язык
Customer Service
Help Contact us
Copyright © . All rights reserved. Scopus® is a registered trademark of Elsevier B.V.
We use cookies to help provide and enhance our service and tailor content. By continuing, you agree to the .
Terms and conditions ↗ Privacy policy ↗ Elsevier B.V ↗
use of cookies
Source details
MATEC Web of Conferences
Scopus coverage years: from 2012 to 2018
E-ISSN: 2261-236X
Subject area:
Engineering: General Engineering Materials Science: General Materials Science Chemistry: General Chemistry(coverage discontinued in Scopus)
View all documents ▻ Save to source list
CiteScore 2018
0.42
SJR 2018
0.169
SNIP 2018
0.548
CiteScore CiteScore rank & trend CiteScore presets Scopus content coverage
Calculated using data from 30 April, 2019
CiteScore
*CiteScore includes all available document types
0.42
=Citation Count 2018 Documents 2015 -
2017*
=
Metrics displaying this icon are compiled according to , a collaboration between industry and academia.
2018
▻ 3,909 Citations 9,385 Documents ▻
▻
View CiteScore methodology CiteScore FAQ▻
↗
Snowball Metrics
CiteScore rank
Category Rank Percentile
Engineering
#193/275 29th
Materials Science
#322/438 26th
General Engineering
General Materials Science
▻
View CiteScore trends
🔗
Add CiteScore to your site
About Scopus
What is Scopus Content coverage Scopus blog Scopus API Privacy matters
Language
⽇本語に切り替える 切换到简体中文 切換到繁體中文 Русский язык
Customer Service
Help Contact us
Copyright © . All rights reserved. Scopus® is a registered trademark of Elsevier B.V.
Terms and conditions ↗ Privacy policy ↗ Elsevier B.V ↗
Brought to you by
Universitas Diponegoro
Search Sources Lists SciVal ↗ Create account Sign in
ISBN: 978-1-5108-6104-6
2nd International Joint Conference on Advanced Engineering and
Technology (IJCAET 2017) and International Symposium on
Advanced Mechanical and Power Engineering (ISAMPE 2017)
Bali, Indonesia
24 – 26 August 2017
Editors:
B.H. Setiadji A.L. Han A. Widodo
J.D. Setiawan O. Kurdi
J.U.D. Hatmoko
MATEC Web of Conferences Volume 159 (2018)
9/2/2019 Keynote Speakers – IJCAET 2017
ijcaet.undip.ac.id/2017/keynote-speakers/ 1/2
+62-24-7460053 ijcaet@ft.undip.ac.id
HOME CONFERENCE COMMITTEE SPEAKERS SUBMISSION ONLINE REGISTRATION PREVIOUS IJCAET & ISAMPE PARTNERSHIP
1 Dr. Arcandra Tahar Vice Minister of Energy and Mineral Resources, the Republic of Indonesia Presentation Title: TBA
2 Prof. Alexander Cuthbert Emeritus Professor of Planning and Urban Development, The University of
GENERAL INFORMATIONS
ISAMPE 2017 Visa Application Important Dates
Program Book and Poster More About Bali
Contact Us
9/2/2019 Keynote Speakers – IJCAET 2017
ijcaet.undip.ac.id/2017/keynote-speakers/ 2/2
New South Wales, Sydney, Australia
Presentation Title: “Robots, Wind farms, and the internet : The ethics of technology in a changing world”
Download abstract
3 Prof. Andrew Price Loughborough University, UK
Civil and Building Engineering Department
Presentation title: “Improving critical infrastructure performance through advanced engineering and innovation”
Download abstract
4 Assoc. Prof. Tomomi Honda
University of Fukui, Japan
Department of Mechanical Engineering, Faculty of Engineering Graduate School of Engineering
Presentation Title: “New diagnosis methods of the lubrication oils for the proactive maintenance“
Download abstract
INFORMATION FOR AUTHORS
Noti cation of Approval Formatting Instructions Online Registration Method of Payment
© 2019 IJCAET 2017 | Designed by: Theme Freesia | Powered by: WordPress View statistics
9/2/2019 Invited Speakers – IJCAET 2017
ijcaet.undip.ac.id/2017/invited-speakers/ 1/3
+62-24-7460053 ijcaet@ft.undip.ac.id
HOME CONFERENCE COMMITTEE SPEAKERS SUBMISSION ONLINE REGISTRATION PREVIOUS IJCAET & ISAMPE PARTNERSHIP
1 Prof. Buntara Sthenly Gan Architecture Department Nihon University, Koriyama Japan Presentation Title: “Isogeometric Analysis for Beam Element”
GENERAL INFORMATIONS
ISAMPE 2017 Visa Application Important Dates
Program Book and Poster More About Bali
Contact Us
9/2/2019 Invited Speakers – IJCAET 2017
ijcaet.undip.ac.id/2017/invited-speakers/ 2/3
2 Assoc. Prof. Tegoeh Tjahjowidodo
School of Mechanical and Aerospace Engineering, Nanyang Technological University (NTU), Singapore
Presentation Title: “An Integrated-Intelligent Re-manufacturing Process”
Download abstract
3 Prof. Niro Nagai Mechanical Engineering Department, University of Fukui, Japan
Presentation Title: “Boiling research in Japan, cooling technology of high- temperature material”
Download abstract
4 Assoc. Prof. Rosdiazli Ibrahim
Electrical and Electronics Engineering Department, Universiti Teknologi Petronas (UTP), Malaysia
Dean of Centre for Graduate Studies (UTP)
Presentation Title: “The journey towards industrial monitoring and control application of wirelessHART technology“
Download abstract
5 Prof. Junghwan Oh Biomedical Engineering Department, Pukyong National University (PKNU), Korea
Presentation Title: TBA
6 Prof. Prabir Basu Mechanical Enginering Department, Dalhousie University, Nova Scotia, Canada
INFORMATION FOR AUTHORS
Noti cation of Approval
Formatting Instructions
Online Registration
Method of Payment
9/2/2019 Invited Speakers – IJCAET 2017
ijcaet.undip.ac.id/2017/invited-speakers/ 3/3
Presentation Title: “Torrefaction – an easier, simpler, inexpensive immediately implementable option of reduction in greenhouse gas emission”
Download abstract
© 2019 IJCAET 2017 | Designed by: Theme Freesia | Powered by: WordPress View statistics
9/2/2019 Organizing Committee – IJCAET 2017
ijcaet.undip.ac.id/2017/organizing-committee/ 1/5
+62-24-7460053 ijcaet@ft.undip.ac.id
HOME CONFERENCE COMMITTEE SPEAKERS SUBMISSION ONLINE REGISTRATION PREVIOUS IJCAET & ISAMPE PARTNERSHIP
Conference Chair Jati Utomo Dwi
Hatmoko (General chair) – UNDIP
GENERAL INFORMATIONS
ISAMPE 2017 Visa Application Important Dates
Program Book and Poster
9/2/2019 Organizing Committee – IJCAET 2017
ijcaet.undip.ac.id/2017/organizing-committee/ 2/5
Tae Wan Kim – PKNU
Ngakan Putu Sueca –
UNUD
Conference Secretary Gunawan Dwi Haryadi
– UNDIP
Organizing Committee Joga Dharma
Setiawan – UNDIP
Antonius Karel Mukti
Wibowo – UNUD
In Pill Kang – PKNU
Program Chair Thomas Triadi
Putranto – UNDIP
E ita Yohana – UNDIP
I Nyoman Satya
Kumara – UNUD
More About Bali Contact Us
INFORMATION FOR AUTHORS
Noti cation of Approval
Formatting Instructions
Online Registration
Method of Payment
9/2/2019 Organizing Committee – IJCAET 2017
ijcaet.undip.ac.id/2017/organizing-committee/ 3/5
Young Whan Park –
PKNU
Proceeding Manager Ojo Kurdi- UNDIP
Mochammad Ariyanto
– UNDIP
Rando Tungga Dewa –
PKNU
Ainul Ghurri – UNUD
Website/Publicity/Photographer Eko Didik Widianto –
UNDIP
Dwi Putra Githa –
UNUD
Archit Fadhilah –
UNDIP
Treasury Yuni Nurjanah –
UNDIP
9/2/2019 Organizing Committee – IJCAET 2017
ijcaet.undip.ac.id/2017/organizing-committee/ 4/5
Siti Maskatul Atnah –
UNDIP
Yheri Dita Meinar –
UNDIP
Ni Kadek Ayu Wirdiani
– UNUD
Supporting Member Heppy Haryanta – UNDIP Fajar Purwantoro – UNDIP Bayu Prasetyo – UNDIP Yulita Arni Priastiwi – UNDIP Isnaini Wulansari – UNDIP
Indra Sutanto – UNDIP
Muhammad Al an Hidayat – UNDIP Muhammad Luthfan Farizan – UNDIP
Muchamad Iqbal Rokhim – UNDIP Suluh Pertiwanda – UNDIP Dimas Adib Karomi – UNDIP Abdi Gilang Amrizal – UNDIP
M. Fandiar Majiid – UNDIP Riventus A.H. Aritonang – UNDIP Farika Tono Putri – UNDIP
I Made Agus Ariawan – UNUD
Komang Oka Saputra – UNUD
Dw. Made P. Wedagama – UNUD
I Wayan Yuda Manik – UNUD
9/2/2019 Organizing Committee – IJCAET 2017
ijcaet.undip.ac.id/2017/organizing-committee/ 5/5
Diaz Surgatha Rokhmani – UNUD Fajar Rizky Kurniawan – UNUD I Gede Bayu Suarsa – UNUD Ganggas Bagus Mauana Idham – UNUD
Kelvin Judika Riccardo Marbun – UNUD
Jauzaa Maylia Suhendro – UNUD A. A. Tri Budi Artawan – UNUD Ni Made Anita Belinda – UNUD Putu Ratih Devyanti – UNUD Ida Ayu Sri Sinta Anjani – UNUD I Made Indra Wiguna – UNUD Haksari Laksmi Bestari – UNUD Luh Ayu Sutawati – UNUD
Maria Gusti Agung Ayu Permata – UNUD
Note: UNDIP = Diponegoro University, PKNU = Pukyong National University, UNUD = Udayana University
© 2019 IJCAET 2017 | Designed by: Theme Freesia | Powered by: WordPress View statistics
9/2/2019 Scientific Committee – IJCAET 2017
ijcaet.undip.ac.id/2017/scientific-commitee/ 1/3
+62-24-7460053 ijcaet@ft.undip.ac.id
HOME CONFERENCE COMMITTEE SPEAKERS SUBMISSION ONLINE REGISTRATION PREVIOUS IJCAET & ISAMPE PARTNERSHIP
Bagus Hario Setiadji – Diponegoro University, Indonesia
(Chair)
GENERAL INFORMATIONS
ISAMPE 2017 Visa Application Important Dates
Program Book and Poster
9/2/2019 Scientific Committee – IJCAET 2017
ijcaet.undip.ac.id/2017/scientific-commitee/ 2/3
Abraham Christian – National University of Singapore, Singapore Achmad Widodo – Diponegoro University, Indonesia
Agus Budiyono – Center for Unmanned System Studies, Bandung Inst. of Technology, Indonesia
Athanasius Bayuseno – Diponegoro University, Indonesia Benny Suryanto – Herriot Watt University, United Kingdom Buntara Gan – Nihon University, Japan
Buyung Kosasih – University of Wollongong, Australia
Choi Kwang Hwan – Pukyong National University, South Korea Dani Hermanto – Derby University, United Kingdom
Dewa Made Wiharta – Udayana University, Indonesia Dewi Wirastuti – Udayana University, Indonesia Hadiyanto – Diponegoro University, Indonesia Han Ay Lie, – Diponegoro University, Indonesia
Hari Murti Hadikusumo – Asian Institute of Technology, Thailand Henk Jonkers – TU Delft, Netherland
Heru Susanto – Diponegoro University, Indonesia IAD Giriantari – Udayana University, Indonesia
I Dewa Gede Ary Subagia – Udayana University, Indonesia I Ketut Gede Darma Putra – Udayana University, Indonesia I Ketut Sudarsana – Udayana University, Indonesia
I Putu Agung Bayupati – Udayana University, Indonesia Ismoyo Haryanto – Diponegoro University, Indonesia Istadi – Diponegoro University, Indonesia
Jamari – Diponegoro University, Indonesia
Jang Dong Wook – Pukyong National University, South Korea Jundika Candra Kurnia – University Technology Petronas, Malaysia Kang Hyun-wook – Pukyong National University, South Korea Kim Chan-Jung – Pukyong National University, South Korea Linawati – Udayana University, Indonesia
Lim Young-su – Pukyong National University, South Korea Mochammad Facta – Diponegoro University, Indonesia Nita Ariyanti – Diponegoro University, Indonesia Nyoman Putra Sastra – Udayana University, Indonesia Nyoman Pramaita – Udayana University, Indonesia
Park Sang Hong – Pukyong National University, South Korea Ramani Kannan – University Technology Petronas, Malaysia Richard A. William – Herriot Watt University, United Kingdom
More About Bali Contact Us
INFORMATION FOR AUTHORS
Noti cation of Approval
Formatting Instructions
Online Registration
Method of Payment
9/2/2019 Scientific Committee – IJCAET 2017
ijcaet.undip.ac.id/2017/scientific-commitee/ 3/3
Robby Soetanto – Loughborough University, United Kingdom Rukmi Sari Hartati – Udayana University, Indonesia
Oka Saputra – Udayana University, Indonesia
Seo Won Chan – Pukyong National University, South Korea Seo Young-chul – Pukyong National University, South Korea Sonny Irawan – University Technology Petronas, Malaysia
Tegoeh Tjahjowidodo – Nanyang Technological University, Singapore Turnad Lenggo Ginta – University Technology Petronas, Malaysia Wahyu Caesarendra – Nanyang Technological University, Singapore Wayan Redana – Udayana University, Indonesia
WG Ariastina – Udayana University, Indonesia
© 2019 IJCAET 2017 | Designed by: Theme Freesia | Powered by: WordPress View statistics
9/2/2019 International Advisory Board – IJCAET 2017
ijcaet.undip.ac.id/2017/international-advisory-board/ 1/2
+62-24-7460053 ijcaet@ft.undip.ac.id
HOME CONFERENCE COMMITTEE SPEAKERS SUBMISSION ONLINE REGISTRATION PREVIOUS IJCAET & ISAMPE PARTNERSHIP
9/2/2019 International Advisory Board – IJCAET 2017
ijcaet.undip.ac.id/2017/international-advisory-board/ 2/2
1 M. Agung Wibowo DEAN Faculty of Engineering – Diponegoro University, Indonesia
2 Seon Jin Kim DEAN College of Engineering – Pukyong National University, South Korea
3 Ngakan Putu Gede Suardana
DEAN Faculty of Engineering – Udayana University, Indonesia
GENERAL INFORMATIONS
ISAMPE 2017 Visa Application Important Dates
Program Book and Poster More About Bali
Contact Us
INFORMATION FOR AUTHORS
Noti cation of Approval Formatting Instructions Online Registration Method of Payment
© 2019 IJCAET 2017 | Designed by: Theme Freesia | Powered by: WordPress View statistics
Printed from e-media with permission by:
Curran Associates, Inc.
57 Morehouse Lane Red Hook, NY 12571
Some format issues inherent in the e-media version may also appear in this print version.
This work is licensed under a Creative Commons Attribution license:
http://creativecommons.org/licenses/by/2.0/
You are free to:
Share – copy and redistribute the material in any medium or format.
Adapt – remix, transform, and build upon the material for any purpose, even commercial.
The licensor cannot revoke these freedoms as long as you follow the license terms.
Under the following terms:
You must give appropriate credit, provide a link to the license, and indicate if changes were made.
You may do so in any reasonable manner, but not in any way that suggests the licensor endorses you or your use. The copyright is retained by the corresponding authors.
Printed by Curran Associates, Inc. (2018)
For additional information, please contact EDP Sciences – Web of Conferences at the address below.
EDP Sciences – Web of Conferences 17, Avenue du Hoggar
Parc d'Activité de Courtabœuf BP 112
F-91944 Les Ulis Cedex A France
Phone: +33 (0) 1 69 18 75 75 Fax: +33 (0) 1 69 28 84 91 contact-edps@webofconferences.org
Additional copies of this publication are available from:
Curran Associates, Inc.
57 Morehouse Lane Red Hook, NY 12571 USA Phone: 845-758-0400 Fax: 845-758-2633
Email: curran@proceedings.com
Web: www.proceedings.com
TABLE OF CONTENTS
HOUSING TYPOLOGY OF BALI AGA ARCHITECTURE IN SUKAWANA VILLAGE:
DEVELOPMENTS AND CHALLENGE... 1 Yudantini Ni Made, Surya Darma Kadek Agus
AN INVESTIGATION OF SPATIAL ARRANGEMENT, FORM, AND STRUCTURAL SYSTEM
OF TRADITIONAL HOUSES IN PEDAWA INDIGENOUS VILLAGE - BALI... 7 Prajnawrdhi Tri Anggraini
SUSTAINABLE STREETSCAPE DESIGN GUIDELINE BASED ON UNIVERSAL DESIGN
PRINCIPLES... 13 Harsritanto Bangun Ir
ON THE SOUND ABSORPTION IMPROVEMENT OF WATER HYACINTH AND COCONUT
HUSK BASED FIBER REINFORCED POLYMER PANEL... 18 Setyowati Erni, Yahya Iwan, Supriyo Edi, Romadhona Intan C., Minardi Aris
DYNAMIC RESPONSE OF RC CANTILEVER BEAM BY EQUIVALENT SINGLE DEGREE OF FREEDOM METHOD ON ELASTIC ANALYSIS – A REVIEW ON TRANSFORMATION
FACTORS AND DYNAMIC MAGNIFICATION FACTORS... 24 Tudjono Sri, Kusumaningrum Patria
DEVELOPMENT OF BACK-CALCULATION MODEL FOR AGGREGATE GRADATION
DETERMINATION USING FRACTAL THEORY... 30 Hario Setiadji Bagus, Supriyono, Purwanto Djoko
MODELLING AND ANALYSIS THE EFFECT OF UNBALANCED MOMENT DIRECTIONS ON
BEHAVIOUR OF EDGE COLUMN-SLAB CONNECTIONS... 36 Sudarsana I Ketut, Wiryadi I Gede Gegiranang, Susila Gede Adi
EFFECT OF CEMENT VARIATION ON PROPERTIES OF CLC CONCRETE MASONRY
BRICK... 42 Sutandar Erwin, Supriyadi Asep, Andalan Cek Putera
COMPARISON OF GENETIC ALGORITHM AND HARMONY SEARCH METHOD FOR 2D
GEOMETRY OPTIMIZATION.... 48 Ghozi Mohammad, Budiati Anik
INTERVAL CONFINEMENT IN COMPRESSION ZONE TO EVALUATED BEAMS
PERFORMANCE SUBJECTED MONOTONIC LOADS... 54 Priastiwi Yulita Arni, Imran Iswandi, Nuroji, Yuniarto Adi Rudi
DEVELOPMENT OF SEISMIC RISK MICROZONATION MAP FOR SEMARANG DUE TO
SEMARANG FAULT EARTHQUAKE SCENARIOS WITH MAXIMUM MAGNITUDE 6.9 MW... 60 Partono Windu, Irsyam Masyhur, Retno Wardani Sri Prabandiyani
PROJECT COST ESTIMATION BASED ON STANDARD PRICE OF GOODS AND SERVICES
(SHBJ)... 66 Arif Ghuzdewan Toriq, Petra Kartika Narindri Brigitta
RIGHT TURN COEFICIENT EVALUATION ANALYSIS ON INTERSECTION CAPASITY FORMULA AT INDONESIA HIGHWAY CAPASITY MANUAL 1997 USING VEHICLE
TRACKING SIMULATION... 71 Kami Hari Basuki, Djoko Purwanto
THE INFLUENCE OF FREIGHT GENERATION PRODUCTION CHARACTERISTICS OF THE INTERNAL – REGIONAL ZONE COMMODITIES ON SUSTAINABLE FREIGHT
TRANSPORTATION HIGHWAY NETWORK SYSTEM... 77 Akbardin Juang, Parikesit Danang, Riyanto Bambang, Taufik Mulyono Agus
DEVELOPING A PROTOTYPE OF EARLY WARNING SYSTEM OF DELAY RISKS FOR
PUBLIC PROJECTS (EWASDRIP)... 83 Utomo Dwi Hatmoko Jati, Priyono Hery, Agung Wibowo Mochamad, Radian Khasani Riqi
DEVELOPMENT OF INSTITUTIONAL FUNDING MODEL OF DEEP DISCOUNT BOND AND
LAND LEASE ON A TOLL ROAD PROJECT... 89 Dwirahman Randika, Latief Yusuf, Dita Rarasati Ayomi
THE COMPARISON OF BOND STRENGTH BETWEEN GEOPOLYMER CONCRETE AND OPC
CONCRETE FOR PLAIN REINFORCING BARS... 95 Nuroji, Herdian Primadyas Daniel, Nurhuda Ilham, Muslikh
BEHAVIOR OF GEOPOLYMER CONCRETE CONFINED BY CIRCULAR HOOPS... 101 Muslikh, Anggraini N. K., Hardjito D., Antonius
DEVELOPMENT OF RISK-BASED STANDARDIZED WBS (WORK BREAKDOWN STRUCTURE) FOR QUALITY PLANNING OF HIGH RISE BUILDING ARCHITECTURAL
WORKS... 108 Rianty Mirradewi, Latief Yusuf, Riantini Leni Sagita
COMPONENTS OF INDONESIAN TRADITIONAL MARKET: DESIGN TOOLS FOR
REVITALISATION... 114 Hermawan Ferry, Indarto Himawan, Ismiyati
RIVER CONSERVATION USING SECEEL APPROACH: A CASE STUDY ON EAST FLOOD
WAY RIVER, SEMARANG, CENTRAL JAVA, INDONESIA... 120 Sriyana Ignatius
DETERMINING FACTORS FOR IMPLEMENTING GREEN SUPPLY CHAIN MANAGEMENT
IN THE CONSTRUCTION INDUSTRY: A LITERATURE REVIEW... 125 Wibowo Mochammad Agung, Handayani Naniek Utami, Mustikasari Anita, Nurdiana Asri, Soleh M. Nur
SUSTAINABLE COMMUNITY BASED WATER SUPPLY AT SALATIGA BY USE OF RAPFISH
METHOD... 131 Suharyanto, Deasy K Angelica, Sudarno
INDONESIAN HIGHWAY CAPACITY GUIDANCE (IHCG) CORRECTION FACTOR FOR
SIGNALIZED INTERSECTION... 137 Indriastuti Amelia K., Yulipriyono Eko
CRITICAL SUCCESS FACTORS IN DEVELOPING COLLABORATIVE DESIGN-BUILD
PROJECT TEAM TO IMPROVE PROJECT PERFORMANCE... 143 Nursin Afrizal, Latief Yusuf, Ibrahim
OPTIMIZATION OF IRRIGATION WATER USE TO INCREASE THE BENEFIT OF
AGRICULTURAL PRODUCTS... 149 Soentoro Edy Anto, Perwira Erlangga, Suryadi Yadi, Winskayati
GREEN HOUSE GASES (GHG’S) EMISSION REDUCTION MEASURES AND VERIFICATION
CHALLENGE AT TRANSPORT SECTOR... 155 Huboyo Haryono, Wibowo Hari, Retna Sari Winda
LIFE-CYCLE ASSESSMENT OF CRUDE PALM OIL PRODUCED AT MILL J, PT XYZ,
SUMATERA ISLAND USING ECO-INDICATOR 99... 161 Andarani Pertiwi, Dwi Nugraha Winardi, Sawitri Desinta, Budiawan Wiwik
RECOVERY PRACTICE OF UNSORTED SOLID WASTE: FROM LANDFILL TOWARDS
ECONOMIC BENEFITS IN SEMARANG, INDONESIA... 167 Arief Budihardjo Mochamad, Fajarini Sri Wahyuningrum Indah
METHANE ENRICHMENT ON BIOGAS GENERATED FROM ANAEROBIC DIGESTER USING
COCONUT SHELL-BASED ACTIVATED CARBON... 172 Hakim Ridwan, Suwartha Nyoman, Priadi Cindy
ANALYSIS OF GROUNDWATER QUALITY SURROUNDING MUNICIPAL SOLID WASTE
LANDFILL: BANYUURIP LANDFILL, MAGELANG, INDONESIA... 178 Arief Budihardjo Mochamad, Purwono, Selfi Nugraheni Annisa
PREDICTING LEAD (PB) CONTAMINANT MIGRATION THROUGH LANDFILL LINER... 184 Purwono, Arief Budihardjo Mochamad
LEAVES COMPOSTING PROCESS AND THE INFLUENCE OF RUMEN CONTENT AND BRAN
ADDITION... 189 Arief Budihardjo Mochamad, Sutrisno Endro, Purwono, Fatimah Maulia
ANALOG STUDY OF FLUID FLOW ON DEFORMATION BAND AT PETANI FORMATION,
RIAU, INDONESIA... 193 Choanji Tiggi, Rita Novia, Yuskar Yuniarti, Pradana Aulia
PALAEOECOLOGICAL ANALYSIS OF SENTOLO FORMATION BASED ON FORAMINIFERA FOSSIL ASSEMBLAGE FROM STRATIGRAPHIC CROSS-SECTIONAL MEASUREMENTS IN
PENGASIH, KULON PROGO, YOGYAKARTA... 199 Kurniasih Anis, Idham Fauzan Muhammad, Winarno Tri, Setyawan Reddy
APPLICATION OF AQUIFER VULNERABILITY INDEX (AVI) METHOD TO ASSESS
GROUNDWATER VULNERABILITY TO CONTAMINATION IN SEMARANG URBAN AREA... 205 Putranto Thomas Triadi, Santi Narulita, Widiarso Dian Agus, Pamungkas Dimas
THE INFLUENCE OF FAULT AND STRESS CONTRIBUTED ON OVERPRESSURE MECHANISM FOR NEOGEN FORMATION (MUNDU, WONOCOLO, NGRAYONG) EAST
JAVA BASIN, INDONESIA... 211 Fahrudin, Nugroho Hadi, Winarno Tri, Hayuddin Zul, Suprayetno Joko, Firmansyah Rully, Muhajir, Kadarusman
Ade
CHARACTERISTICS OF LATERITIC NICKEL MINERALIZATION IN MID PART OF
MADANG AND SERAKAMAN AREAS, SEBUKU ISLAND, SOUTH KALIMANTAN... 217 Aribowo Yoga, Syahputra Yudi, Agus Widiarso Dian
ANALYSIS OF PIPING AT KEDUNG ULING EARTHFILL DAM, WONOGIRI REGENCY,
CENTRAL JAVA PROVINCE, INDONESIA... 223 Najib, Setyawan Agus, Ardyarini Indriyani, Joko Suprapto Dwiyanto
THE ANALYSIS OF VOLCANIC ACTIVITY INFLUENCES AT THE LOWER AND MIDDLE
PART OF SENTOLO FORMATION, KULON PROGO USING PETROGRAPHIC METHOD... 229 Winarno Tri, Marin Jenian, Hani Pratama Ilham, Kurniasih Anis
ANALYSIS OF LANDSLIDE DISASTER IMPACT IDENTIFICATION USING UNMANNED AERIAL VEHICLE (UAV) AND GEOGRAPHIC INFORMATION SYSTEM (GIS) (CASE STUDY:
NGESREP SUB DISTRICT, SEMARANG CITY)... 235 Prasetyo Yudo, Bashit Nurhadi, Azeriansyah Reyhan
THE SPATIAL ANALYSIS TO CHOOSE A LOCATION TO BE DESIGNATED AS A LANDFILL
SITE... 241 Zaim Zaflis, Asteriani Febby
DEVELOPMENT OF TWO COMPONENTS ACCELERATION TIME HISTORIES FOR
SEMARANG, INDONESIA, DUE TO SEMARANG FAULT EARTHQUAKE SCENARIOS USING
30 METERS SOIL DEPOSIT MODEL... 247 Partono Windu
SPATIAL STUDIES AND JURIDICAL UTILIZATION OF VACANT LAND AND ABANDONED
LAND CONTROL IN EFFORTS OF REGIONAL AUTHORITY IN SEMARANG CITY... 253 Subiyanto Sawitri, Janu Amarrohman Fauzi
DEVELOPMENT OF COLLABORATION IN SUSTAINABLE AGRIBUSINESS CLUSTER... 259 Perdana Tomy, Arari H. Mahra, Rahayu H. Fernianda, Ginanjar Tetep, Sesy N. P. Ajeng
COORDINATION AND COLLABORATION FUNCTIONS OF DISASTER MANAGEMENT
CENTERS FOR HUMANITARIAN LOGISTICS: A CASE STUDY AT MERAPI ERUPTION... 265 Handayani Naniek Utami, Mustikasari Anita
E-TRANSLATOR KAWI TO BAHASA... 271 Sudana Oka, Putra Darma, Sudarma M., Hartati Rukmi S., Pradnya Prastika Ryan, Wirdiani Ayu
HOUSING SATISFACTION AND WILLINGNESS TO MOVE TO LOW-COST RENTAL
APARTMENTS OF SLUM DWELLERS IN SEMARANG URBAN AREA... 277 Manaf Asnawi, Wahyono Hadi, Puspita Sari Ita, Aprilia Dias
THE POTENTIAL BIODIESEL PRODUCTION FROM CERBERA ODOLLAM OIL (BINTARO)
IN ACEH... 283 Khairil, Rizki Aulia, Iskandar, Jalaluddin, Silitonga A. S., Masjuki H. H., Mahlia T. M. I.
FATIGUE TESTING AND EVALUATION OF FATIGUE STRENGTH UNDER MULTIAXIAL
STRESS STATE\; WHY DO WE NEED FATIGUE TESTING?... 289 Itoh Takamoto, Ogawa Fumio, Morishita Takahiro
EXPERIMENTAL PERFORMANCE STUDIES OF SMALL WALL ROOM AIR CONDITIONER
FOR R410A RETROFITTED WITH R290... 295 Fajar Tk Berkah, Nicolas Dipto I Geraldus
SIMULATION AND ANALYSIS OF THE AEROELASTIC-GALLOPING-BASED
PIEZOELECTRIC ENERGY HARVESTER UTILIZING FEM AND CFD... 301 Haryanto Ismoyo, Widodo Achmad, Prahasto Toni, Satrijo Djoeli, Pradiptya Iswan, Ouakad Hassen
AN INTEGRATION OF PSO-BASED FEATURE SELECTION AND RANDOM FOREST FOR
ANOMALY DETECTION IN IOT NETWORK... 308 Tama Bayu Adhi, Rhee Kyung-Hyune
ANALYSIS OF CALCIUM CARBONATE POLYMORPHS DEPOSITED IN WATER PIPING
SYSTEM AND THE EFFECT OF TARTARIC ACID ADDITIVE... 314 Putranto W. A., Umardhani Y., Sulistyo, Yurianto, Bayuseno A. P.
REAR WHEEL DRIVE RECUMBENT BICYCLE FOR URBAN TRANSPORTATION IN A
TROPICAL EMERGING COUNTRY... 320 Suhardi Bambang, Priadythama Ilham, Laksono Pringgo Widyo
SYNTHESIS OF BARIUM SULFATE IN THE VARIATION OF TEMPERATURE AND
ADDITIVE CONCENTRATION... 326 Ali Waleed, Putranto Wahyu, Muryanto Stefanus, Bayuseno Athanasius
INFLUENCE OF HULL ENTRANCE ANGLE “PERINTIS 750 DWT”, TOWARD SHIP
RESISTANCE: THE CASE STUDY FOR DESIGN DEVELOPMENT “PERINTIS 750 DWT.”... 332 Hadi Eko Sasmito, Manik Parlindungan, Iqbal Muhammad
STRUCTURAL ANALYSIS FOR IN-SERVICE GAS PIPELINE LOWERING USING
NUMERICAL METHOD... 338 Safarudin Mochamad, Setiawan Joga Dharma
RESISTANCE AND STABILITY ANALYSIS FOR CATAMARAN FISHING VESSEL WITH
SOLAR CELL IN CALM WATER... 344 Putranto Teguh, Aryawan Wasis Dwi, Kurniawati Hesty Anita, Setyawan Dony, Pribadi Sri Rejeki Wahyu
SYNTHESIS SENSITIVE LAYER OF ETHYLENE GAS SENSOR BASED TIN OXIDE
NANOPARTICLES USING WATER AS SOLVENT IN PRECIPITATION METHOD... 350 Nabena Erica Caesariaty Harni Prima, Yuliarto Brian, Nugraha, Iqbal Muhammad
PROJECTION MATRIX DESIGN FOR CO-SPARSE ANALYSIS MODEL BASED
COMPRESSIVE SENSING... 356 Oey Endra, Gunawan Dadang, Sudiana Dodi
MACHINE HEALTH PROGNOSIS BASED ON MULTIREGIME CONDITION MONITORING
SIGNALS... 362 Widodo Achmad, Prahasto Toni, Satrijo Djoeli, Setiyana Budi, Sugiyanto, Haryanto Ismoyo, Djoko Susilo Didik
INDUCTION MOTOR CENTRIFUGAL BLOWER HEALTH DIAGNOSTIC BASED ON COLOR
SEGMENTATION OF THERMAL IMAGE AND VIBRATION SIGNAL FEATURE... 368 Widodo Panut, Dwi Haryadi Gunawan, Widodo Achmad
DESIGN STUDIES OF INNER AND OUTER EMBEDDED PERMANENT MAGNET FOR
HYBRID ELECTRIC VEHICLES... 374 Cv Aravind, Kannan Ramani, Lei Heng Jing, Setiawan Joga Dharma
POROSITY CONTROL AND MECHANICAL PROPERTIES OF POROUS CERAMIC
MATERIAL FROM PLERED REGION... 380 Sulistyo S., Rizky
POLYURETHANIZATION TEMPERATURE EFFECT TO THE THERMAL BEHAVIOUR OF
CELLULOSE – FIBER BASED HYBRID POLYURETHANE... 385 Kurnia Adi Herald, Hanum Ikhwan Fauzia, Aidilichsan Muliawan Hasyim, Chalid Mochamad
FAULT DIAGNOSTIC SYSTEM BEARING CENTRIFUGAL PUMP USING K-MEANS METHOD
FOR THERMOGRAPHY IMAGE AND SIGNAL ANALYSIS VIBRATIONS... 391 Yudhistira Hidayat Agung, Widodo Achmad, Dwi Haryadi Gunawan
ADOMIAN DECOMPOSITION METHOD FOR SOLVING INITIAL VALUE PROBLEMS IN
VIBRATION MODELS... 397 Mungkasi Sudi, Ekaputra I Made Wicaksana
EFFECT OF POST CURING METHOD ON FLEXURAL STRENGTH OF COMPOSITE
FRICTION BRAKE... 403 Budiono Herru Santoso, Surojo Eko, Muhayat Nurul, Raharjo Wijang Wisnu
THE INFLUENCE OF WELDING SPEED CONDITIONS OF GMAW ON MECHANICAL
PROPERTIES OF 316L AUSTENITIC STAINLESS STEEL... 409 Ekaputra I. M. W., Mungkasi Sudi, Dwi Haryadi Gunawan, Tungga Dewa Rando, Kim Seon-Jin
MEASUREMENT OF INJURY RATE ON FISH SKIN AND PERFORMANCE COMPARISON
BASED ON L*A*B* AND HSV COLOR SPACES... 415 Tran Minh Thien, Rantung Jotje, Nguyen Trong Hai, Kim Hak Kyeong, Kim Sang Bong
FLAME STABILITY AND BEHAVIOR INSIDE MESO-SCALE COMBUSTOR WITH
DIFFERENT FLAME HOLDER... 421 Yuliati Lilis
NUMERICAL SIMULATION OF HEAT TRANSFER AUGMENTATION IN FIN-AND-TUBE HEAT EXCHANGER WITH VARIOUS NUMBER OF ROWS OF CONCAVE RECTANGULAR
WINGLET VORTEX GENERATOR... 427 Syaiful, Syarifudin Imam, Soetanto Maria F., Bae Myung-Whan
PERFORMANCE ANALYSIS OF SEA WATER SOLAR STILL TO PRODUCE FRESH WATER
AND SALT USING FLAT PLATE COLLECTORS... 433 Mulyanef, Duskiardi, Hidayat Rahmad
THE INFLUENCE OF GUIDE VANE TO THE PERFORMANCE OF CROSS-FLOW WIND
TURBINE ON WASTE ENERGY HARVESTING SYSTEM... 439 Santoso Budi, Danardono Dwi Prija Tjahjana Dominicus
DEVELOPMENT OF TENSION-TORSION MULTIAXIAL CREEP TESTING APPARATUS FOR
HEAT RESISTING STEEL... 445 Hiyoshi Noritake, Iriyama Yoshihisa
PERFORMANCE PREDICTION OF MAGNETORHEOLOGICAL VALVES UNDER VARIOUS
TYPE OF FLUID AND FLUX PATH... 451 Idris Muhammad Hafiz, Mazlan Saiful Amri, Ubaidillah Ubaidillah, Imaduddin Fitrian
SURFACE TEXTURE INFLUENCES ON THE RUNNING-IN BEHAVIOR AND FRICTION
REDUCTION... 457 Hou Zhouyong, Honda Tomomi
ANALYSIS OF CHIP GEOMETRY AND SURFACE ROUGHNESS AT LOW SPEED TURNING
IN VARIOUS COMMERCIAL STEELS... 463 Mudjijanto, Sulistyo, Rusnaldy
COMPARISON OF RATIO LOADED AND UNLOADED FOOT AREA OF FLAT FOOT AND
HEALTHY FOOT IN YOUNGER ADULTS... 469 Dwi Haryadi Gunawan, Basuki Wibowo Dwi, Widodo Achmad, Suprihanto Agus
OPTIMIZATION OF RIDGE WAVEGUIDE STRUCTURE FOR TEMPERATURE SENSOR
APPLICATION USING FINITE DIFFERENCE METHOD... 475 Yulianti Ian, D. P Ngurah Made, Lestiyanti Yuni, Kurdi Ojo
EXPERIMENTAL STUDY PERFORMANCE R-22 AC SPLIT RETROFITTED WITH PROPANE... 481 Ridwan Tanaka Imam, Fajar Berkah, Suryo Utomo Tony, Yohana Eflita, Mustaqim
THE MODELING OF A CONCEPTUAL ENGINEERING DESIGN SYSTEM USING THE
DECISION-MATRIX LOGIC... 487 Ramdhani Safarudin, Jamari J
CHARACTERIZATION CHIP FORMATION OF COMMERCIAL STEEL MATERIALS AT LOW
SPEED CYLINDRICAL GRINDING PROCESSES... 493 Isti Nugroho Wahyu, Nugroho Sri, Rusnaldy
THE PERFORMANCE OF PUMP AS TURBINE WITH MACHINED IMPELLERS... 498 Zariatin D. L, Kumbarasari Shanti, Rahmalina Dwi
A STUDY OF TEA LEAVES DRYING USING DEHUMIDIFICATION PROCESS AND REGENERATION OF LIQUID DESICCANT IN A CLOSED-CYCLE DEHUMIDIFICATION-
HUMIDIFICATION... 504 Yohana Eflita, Endy Yulianto Mohammad, Bahar Shofwan, Alifa Muhammad Azza, Laura Indrayani Novi
MODELING, IDENTIFICATION, AND SIMULATION OF POSITIONAL DISPLACEMENT
CONTROL FOR RIBBON BRIDGES... 510 Trong Nguyen Van, Choi Yong-Woon, Yoon Jung-In, Choi Kwang-Hwan, Son Chang-Hyo, Kim Young-Bok
FAILURE ANALYSIS OF SHAFT CIRCULATING WATER PUMP (CWP) USED IN POWER
PLANT... 516 Hamid Abdul, Nugroho Sri, Dwi Haryadi Gunawan, Khaeroman
DETECTION OF GEAR DEFECTS USING METHOD OF WAVELET DECOMPOSITION AND
CROSS-CORRELATION - EXPERIMENT TO DEVELOP A FEASIBLE DETECTION METHOD... 522 Hidayat R. Lullus Lambang G, Santoso Budi
PATH PLANNING FOR AUTOMATIC GUIDED VEHICLE WITH MULTIPLE TARGET
POINTS IN DYNAMIC ENVIRONMENT... 528 Kim Chang Kyu, Nguyen Huy Hung, Kim Dae Hwan, Kim Hak Kyeong, Kim Sang Bong
DESIGN AND FABRICATION OF A TWIST FIXTURE TO MEASURE TORSIONAL STIFFNESS
OF A PICK UP CHASSIS... 534 Kurdi Ojo, Yob Mohd Shukri, Haji Ishamuddin Awisqarni, Suprihanto Agus, Widyanto Susilo Adi, Wibowo Dwi
Basuki, Yulianti Ian
MORPHOLOGY EVOLUTION OF ZNO THIN FILMS DEPOSITED BY NITROGEN MEDIATED
CRYSTALLIZATION METHOD... 540 Suhariadi Iping, Shiratani Masaharu, Itagaki Naho
DIGITAL INTEGRATED INSTRUMENT FOR MEASURING BMI AND COMPARING TO THE
IDEAL BMI FOR AGE AS A GUIDANCE FOR INDONESIAN MILITARY RECRUITMENT... 546 Basuki Wibowo Dwi, Ismoyo, Suprihanto Agus, Caesarendra Wahyu, Ariyanto Mochammad
EFFECTS OF DIFFERENT HEEL HEIGHTS ON HEEL PRESSURE DISTRIBUTION FOR
CALCANEAL SPUR PATIENTS DURING STANDING: FINITE ELEMENT ANALYSIS... 552 Basuki Wibowo Dwi, Widodo Achmad, Dwi Haryadi Gunawan, Suprihanto Agus
A REVIEW ON SENSORS FOR REAL-TIME MONITORING AND CONTROL SYSTEMS ON
MACHINING AND SURFACE FINISHING PROCESSES... 558 Wijaya Tomi, Caesarendra Wahyu, Tjahjowidodo Tegoeh, Pappachan Bobby K, Wee Arthur, Roslan Muhammad
Izzat
MODAL ANALYSIS OF REPLICA BOSS HOLE DURING THE DEBURRING PROCESS IN
AEROSPACE MANUFACTURING INDUSTRY... 564 Andriani Claudy, Caesarendra Wahyu, Tjahjowidodo Tegoeh, Wijaya Tomi, Pappachan Bobby K
INVESTIGATION OF MECHANICAL PROPERTIES OF AL7SI/ SIC AND AL7SIMG/SIC
COMPOSITES PRODUCED BY SEMI SOLID STIR CASTING TECHNIQUE... 570 Sulardjaka, Nugroho Sri, Suyanto, Fitriana Deni Fajar
MECHANICAL AND MICROSTRUCTURAL CHARACTERIZATION OF ST 37 BUTT JOINTS
BY FRICTION STIR... 576 Kasir, Sulardjaka
CFD ANALYSIS ON THE AERODYNAMICS CHARACTERISTICS OF JAKARTA-BANDUNG
HIGH SPEED TRAIN... 581 Utomo Tony, Fajar Berkah, Arpriyanto Hendry
DESIGN AND SIMULATION OF FUZZY LOGIC BASED TEMPERATURE CONTROL FOR A
MIXING PROCESS IN THERAPEUTIC POOL... 587 Munadi, Ramadhan Erwin F., Ariyanto Mochammad, Iskandar Norman, Amirullah M. A., Julianti Hari P.,
Setiawan Rudy
A GREAT ACHIEVEMENT OF CALCULATED AND EXPERIMENTAL RESULTS OF CHAR
KINETIC RATE IN WOODY MAHOGANY PYROLYSIS... 593 Wijayanti Widya, Nur Sasongko Mega
REMAINING LIFE ASSESSMENT OF SUPERHEATER TUBE IN BOILER OF COAL FIRED
POWER PLANT... 599 Muhajir Habib, Dwi Haryadi Gunawan, Widodo Achmad
3D NUMERICAL STUDY ON THE EFFECT OF SHAFT ECCENTRICITY ON THE
TRIBOLOGICAL PERFORMANCE OF LUBRICATED SLIDING CONTACT... 605 Tauviqirrahman Mohammad, Kurniawan Bayu, Jamari
OPTIMAL PASSIVITY DESIGN OF A VIRTUAL COUPLING INCLUDING FIR-TYPE
FRACTIONAL DERIVATIVES FOR A HAPTIC INTERFACE... 611 Kawai Masayuki, Yamagishi Takuya, Minami Shouta
DEVELOPMENT OF 6 DOF SUPERNUMERARY ROBOTIC FINGERS INTEGRATED WITH 3D
ANIMATION... 617 Ariyanto Mochammad, Setiawan Joga D., Munadi, Ismail Rifky, Arifin Zainal
DESIGN OF A LOW-COST FIXED WING UAV... 623 Ariyanto Mochammad, Setiawan Joga D., Prabowo Teguh, Haryanto Ismoyo, Munadi
THE EFFECT OF ACID LEACHING TIME IN MODIFYING NATURAL ZEOLITE AS
CATALYST FOR TOLUENE STEAM REFORMING... 629 Waluyo Joko, Makertihartha I. G. B. N., Susanto Herri
EFFECT OF QUENCHING AGENT ON DIMENSION STABILITY OF AL 6061-AL2O3
COMPOSITE... 635 Ilham Akbar Hammar, Surojo Eko, Ariawan Dody
DESIGN OF FRACTAL FEATURES-BASED PARTIAL DISCHARGE PATTERN RECOGNITION
USING MULTI SUPPORT VECTOR MACHINE METHOD... 641 Rahayu, Anuraga G. T., Prasetia H., Khayam Umar
A REVIEW OF LOW-CYCLE FATIGUE OF ALLOY 617 FOR USE IN VHTR COMPONENTS:
EXPERIMENTAL OUTLOOK... 647 Dewa Rando Tungga, Park Jeong-Hun, Kim Seon-Jin, Kim Woo-Gon, Kim Eung-Seon, Haryadi Gunawan D.,
Ekaputra I. M. W.
DEVELOPMENT OF FORCE FEEDBACK IN STEERING SYSTEMS FOR VIRTUAL DRIVING
SIMULATOR... 653 Setiawan Joga Dharma, Baharom Masri B., Bin Abdul Wali M. Ammar
ENHANCEMENT SURFACE COATING STAINLESS STEEL AND COPPER USING
ULTRASONIC BATCH... 659 Yuliarto Margen Sendie, Sulistyo S, Nugroho Sri, Setiawan Adi Nugroho Yoga
FABRICATION DYE SENSITIZED SOLAR CELLS (DSSCS) USING ß-CAROTENE PIGMENT
BASED NATURAL DYE.... 665 Nirwana Sari Halidun Wa Ode, Cahya Prima Eka, Yuliarto Brian, Suyatman
ALUMINUM CORNER JOINT USING FRICTION STIR WELDING... 671 B. Darmadi Djarot, Setiawan Widia, Purnowidodo Anindito, Siswanto Eko
THE STRUCTURAL RESPONSE INVESTIGATION OF MODULAR PONTOON COLLAR
FLOATING CAGE DUE TO CURRENT LOAD TO SUPPORT FISH FARMING ACTIVITIES... 677 Windyandari Aulia, Zakki Ahmad Fauzan
IMPACT PHENOMENA ASSESSMENT: PART II – BUFFER CONTAINER AS A MEASURE TO
REDUCE CARGO LEAKAGE IN COLLISION... 683 Rio Prabowo Aditya, Jun Baek Seung, Geon Lee Seung, Myung Bae Dong, Min Sohn Jung, Bahatmaka Aldias,
Samuel Samuel
INVESTIGATION ON THE PERFORMANCE OF THE TRADITIONAL INDONESIAN FISHING
VESSEL... 689 Bahatmaka Aldias, Kim Dong-Joon, Samuel, Rio Prabowo Aditya, Zaw May-Thu
BULBOUS BOW APPLICATIONS ON A CATAMARAN FISHING VESSEL FOR IMPROVING
PERFORMANCE... 695 Samuel, Kim Dong-Joon, Iqbal Muhammad, Bahatmaka Aldias, Rio Prabowo Aditya
ANALYSIS OF EFFECT OF BULBOUS BOW SHAPE TO SHIP RESISTANCE IN CATAMARAN
BOAT... 701 Chrismianto Deddy, Kiryanto, Arswendo Adietya Berlian
NUMERICAL APPROACHES IN IDEALIZING MASS OF FLUID IN TANK FOR SHIP
VIBRATION ANALYSIS... 707 Byeon Jung Hoon, Cho Hyun Jin, Baek Seung Jun, Prabowo Aditya Rio, Bae Dong Myung, Sohn Jung Min
DESIGN AND CONSTRUCTION OF SPUD HOUSING FOR FLOATING DOCK... 713 Hasanudin Hasanudin, Yulianto Ardi Nugroho
IMPACT PHENOMENA ASSESSMENT: PART I – STRUCTURAL PERFORMANCE OF A
TANKER SUBJECTED TO SHIP GROUNDING AT THE ARCTIC... 719 Prabowo Aditya Rio, Byeon Jung Hoon, Cho Hyun Jin, Sohn Jung Min, Bae Dong Myung, Cho Joung Hyung
CALCIUM SOAP FROM PALM FATTY ACID DISTILLATE FOR RUMINANT FEED: CA(OH)2
AS CALCIUM SOURCE... 725 Handojo Lienda, Indarto Antonius, Shofinita Dian, Meitha Anggina, Nabila Rakhmawati, Triharyogi Harry,
Hakim Maulana G. A., Saadi Muhammad R.
EFFECT OF MGO TO FATTY ACID MOLAR RATIO ON THE PRODUCTION OF
MAGNESIUM SALT OF FATTY ACID FROM PALM FATTY ACID DISTILLATES (PFAD) FOR
FOOD ADDITIVES... 730 Listianingrum, Yuniarti Reni, Al-Aziz Rd. H. R. M. T., Rizaldy Defri, Insanu Muhamad, Harimawan Ardiyan,
Lestari Dianika
AN INNOVATIVE METHOD TO PRODUCE DROP-IN FUEL BY ALKALINE EARTH-
TRANSITION METALS BASIC SOAP DECARBOXYLATION... 736 Fredrik Neonufa Godlief, Pratiwi Meiti, Nur Istyami Astri, Elizabeth Lidya, Suminar Dewi Sri, Purwadi Ronny,
Prakoso Tirto, Soerawidjaja Tatang H.
CRYSTALLIZATION OF BARIUM SULFATE (BASO4) IN A FLOWING SYSTEM: INFLUENCE
OF MALIC ACID ON INDUCTION TIME AND CRYSTAL PHASE TRANSFORMATION... 742 Sariman F., Bayuseno A. P., Muryanto S.
IMPROVEMENT OF MAGNETORHEOLOGICAL GREASES WITH SUPERPARAMAGNETIC
NANOPARTICLES... 748 Mohamad Norzilawati, Ubaidillah, Mazlan Saiful Amri, Choi Seung-Bok, Halim Naim Abdul
A QUANTITATIVE ANALYSIS OF SYSTEM READINESS LEVEL PLUS (SRL+):
DEVELOPMENT OF READINESS LEVEL MEASUREMENT... 753 Marlyana Novi, Tontowi Alva Edy, Yuniarto Hari Agung
DESIGN OF KEY PERFORMANCE INDICATORS (KPI) FOR SUSTAINABLE SUPPLY CHAIN
MANAGEMENT (SSCM) PALM OIL INDUSTRY IN INDONESIA... 759 Kusrini Elisa, Primadasa Rangga
USABILITY EVALUATION OF ANTHROPOMORPHIC PROSTHETIC HAND BASED ON ISO
9241-11... 765 Susanto Novie, Budiawan Wiwik, Ismail Rifky, Ariyanto Mochammad, Sahal Ahmad
INTEGRATION BETWEEN GREEN QUALITY FUNCTION DEPLOYMENT, MODULARITY
CONCEPT AND LIFE CYCLE ASSESSMENT TOWARD SUSTAINABLE PRODUCT DESIGN... 771 Prastawa Heru, Hartini Sri, Anshori Mohamat, Hans Siechara, Wimba Christoper
IMPROVING PERFORMANCE MEASUREMENT EFFICIENCY IN PUBLIC SERVICE USING
LEAN SIX SIGMA METHODOLOGY... 777 Adi Wicaksono Purnawan, Prastawa Heru, Pitaloka Ghabyanza, Putri Nurana
EFFECT OF BLANCHING-BRINE-CALCIUM PRETREATMENT ON RED CHILI PEPPER
DRYING... 783 Arifin Uma Fadzilia, Djaeni Mohamad, Utari Febiani Dwi
OPTIMIZATION FOAM MAT DRYING OF ROSELLE (HIBISCUS SABDARIFFA L.) EXTRACT... 789 Djaeni Mohammad, Utari Febiani Dwi, Arifin Uma Fadzilia
THE EFFECT OF SHEAR WALL CONFIGURATION ON SEISMIC PERFORMANCE IN THE
HOTEL BUILDING... 795 Rahmat Wiyono Daud, Milyardi Roi, Lesmana Cindrawaty
PERFORMANCE OF CURRENT TRANSFORMER OPERATE UNDER HARMONIC
CONDITION AND THEIR EFFECTS ON TRANSFORMER DIFFERENTIAL PROTECTION... 802 Nisja Indra
A COMPARATIVE ANALYSIS OF MENTAL WORKLOAD BETWEEN TRAIN AND BUS
DRIVERS... 808 Soewardi Hartomo, Putra Perdana Suteja
Author Index
*Corresponding author: munady096@gmail.com
Design and Simulation of Fuzzy Logic Based Temperature Control for a Mixing Process in Therapeutic Pool
Munadi1,*, Erwin F. Ramadhan1, Mochammad Ariyanto1, Norman Iskandar1, M. Amirullah A.2, Hari P. Julianti3, Rudy Setiawan4
1Dept. of Mechanical Engineering, Diponegoro University, Tembalang, Semarang, 50275, Indonesia
2Garuda Maintenance Facility AeroAsia, Soekarno Hatta International Airport, Cengkareng, Indonesia
3Dept. of Public Health and Preventive Medicine, Diponegoro University, Semarang, Indonesia
4Academy of Marine Engineering-Veteran, Gayamsari-Semarang, Indonesia
Abstract. Stroke is one cause of the most deaths, in which one way of handling stroke can be done with hydrotherapy. Hydrotherapy is a therapy that is done in the therapeutic pool which is filled with warm water in temperature 31º-34º C. When in the warm water, body burden becomes lighter, so the stroke patients with impaired movement of the body can train the nerves and muscles in order to restore the function of these organs. However, the warm water that is used for the therapy is produced by the heater that requires much electrical energy. This research discussed how to use solar energy to produce hot water using Indirect Evacuated Tube Solar Water Heater systems and make the control system for controlling the mixing process between the hot and cold water by using the Fuzzy Logic Control of the Mamdani method. Therapeutic pool system will be modeled using Simulink. Modeling the mixing process is made on the basis of mass balance and energy balance equations. Then the system will be simulated with interrupted condition and gets set value changes in a particular time. The FLC is successfully reached and maintained steady to a set value. The results will be compared to the performance of the one with Proportional Integral Derivative controller.
1 Introduction
Stroke is the leading cause of death in Indonesia. In 2014, according to the Sample Registration Survey (SRS) conducted by Health Research and Development Agency, Ministry of Health shows, that stroke and heart attack becomes the first and second causes of death in Indonesia, with a percentage of 21.1% and 12.9% of 41,590 deaths nationwide throughout 2014. However, at this time the stroke treatment can be done in several ways, one of them is hydrotherapy. Hydrotherapy is an exercise therapy using warm water in the hydrotherapy pool (therapeutic pool). This therapy is one method of healing therapy against a stiff joint disease caused by stroke. The water used has a temperature between 31º-34º C, the temperature is quiet safe and provide a relaxing effect, can expedite the blood circulation, decrease pain and improve the ability of organ motion. The hot water used in
© The Authors, published by EDP Sciences. This is an open access article distributed under the terms of the Creative Commons Attribution License 4.0 (http://creativecommons.org/licenses/by/4.0/).
MATEC Web of Conferences 159, 02039 (2018) https://doi.org/10.1051/matecconf/201815902039 IJCAET & ISAMPE 2017
Fatigue Testing and Evaluation of Fatigue Strength under Multiaxial Stress State;
Why do we need fatigue testing?
Takamoto Itoh*, Fumio Ogawa and Takahiro Morishita
Ritsumeikan University, Department of Mechanical Engineering, College of Science and Engineering, 1-1-1 Nojihigashi, Kusatsu-shi, Shiga, 525-8577, Japan
Abstract. Types of multiaxial fatigue tests and their experimental results are presented in this paper. There are typical three types in multiaxial fatigue tests: the combining push-pull and reversed torsion loading test using hollow cylinder specimen, the biaxial tension-compression test using cruciform specimen and the inner pressure applied the push-pull loading test using the hollow cylinder specimen. In the combining a push-pull loading and a reversed torsion loading test, failure life under non- proportional loading in which principal directions of stress and strain were changed in a cycle was shortened compared to proportional loading in which those are fixed. Fatigue lives were well-correlated using a non- proportional strain range considering the effect of strain path and material dependence. In the biaxial tension-compression test, the failure life decreased with increase of the principal strain ratio. In the inner pressure applied the push-pull loading test, cyclic deformation behaviour due to complex loading paths of multiaxial fatigue tests with the inner pressure associated with push-pull and rev. torsion acted to reduce the failure lives.
Experimental investigation of multiaxial failure life and elucidation of their governing mechanism is essential and it can broaden the applicability of structural components.
1 Introduction
Investigation of fatigue properties is essential for design of structural components. In practical application, structures are subjected to complex multiaxial load. Therefore, the understanding of multiaxial fatigue properties of materials is important. Indeed, failure lives are overestimated when the effect of multiaxiality is neglected. Multiaxial fatigue testing usually has been carried out using a hollow cylinder specimen by applying push-pull loading and a reversed torsion loading and the applicability of multiaxial stress and strain parameters has been discussed [1-5]. However, a principal strain ratio (
) and a principal stress ratio () ranges performable by the testing method are –1–ν and –10, where ν is the Poisson’s ratio. Structural components sometimes undergo fatigue damage at principal strain/stress ratios in excess of the above range under service loading. In
ȗCorresponding author: itohtaka@fc.ritsumei.ac.jp© The Authors, published by EDP Sciences. This is an open access article distributed under the terms of the Creative Commons Attribution License 4.0 (http://creativecommons.org/licenses/by/4.0/).
MATEC Web of Conferences 159, 01050 (2018) https://doi.org/10.1051/matecconf/201815901050 IJCAET & ISAMPE 2017
An Integration of PSO-based Feature Selection and Random Forest for Anomaly Detection in IoT Network
Bayu Adhi Tama1,Kyung-HyuneRhee1*
1Information Security and Internet Applications Lab., IT Convergence and Application Engineering, Pukyong National University
Daeyon Campus, 45, Yongso-ro, Nam-Gu. Busan, South Korea 48513
Abstract. The most challenging research topic in the field of intrusion detection system (IDS) is anomaly detection. It is able to repeal any peculiar activities in the network by contrasting them with normal patterns.
This paper proposes an efficient random forest (RF) model with particle swarm optimization (PSO)-based feature selection for IDS. The performance model is evaluated on a well-known benchmarking dataset, i.e. NSL-KDD in terms of accuracy, precision, recall, and false alarm rate (FAR) metrics. Furthermore, we evaluate the significance differences between the proposed model and other classifiers, i.e. rotation forest (RoF) and deep neural network (DNN) using statistical significance test. Based on the statistical tests, the proposed model significantly outperforms other classifiers involved in the experiment.
1 Introduction
The present escalation of Internet of Things (IoT) devices and services has changed our daily life dramatically. Many applications are built based on IoT technologies, i.e. smart cities, smart health care, smart home and vehicular networks [1]. Apart from these benefits, attackers may take this such opportunity to launch malevolent code or program to the network. According to [2], security is a key barrier of the implementation of IoT network and services. This is because IoT works with different standard and protocol forming a heterogeneous network. Moreover, IoT devices prevalently produce a huge amount of data so it might become a big threat as malicious users can intercept the data while it is transmitted.
As the development of IoT devices increase, insecure information processing might immediately affects to the whole IoT network. The jeopardy of information disclosure in public space will increase caused by the broadly development of IoT. As presented in Figure 1, security architecture in IoT is divided into three layers, i.e. perception layer, transportation layer, and application layer [3] [4]. Transportation layer comprises network access security which is responsible for attack detection and prevention. An intrusion detection system (IDS) is one security solution which can be deployed in the transportation
*Corresponding author: khrhee@pknu.ac.kr
© The Authors, published by EDP Sciences. This is an open access article distributed under the terms of the Creative Commons Attribution License 4.0 (http://creativecommons.org/licenses/by/4.0/).
MATEC Web of Conferences 159, 01053 (2018) https://doi.org/10.1051/matecconf/201815901053 IJCAET & ISAMPE 2017
Measurement of injury rate on fish skin and performance comparison based on L*A*B* and HSV color spaces
Minh Thien Tran1,Jotje Rantung1,Trong Hai Nguyen1,Hak Kyeong Kim1 and Sang Bong Kim1,*
1Department of Mechanical Design Engineering, Pukyong National University, Busan, 48547, Republic of Korea
Abstract. This paper analyses and compares the performance of L*A*B*
and HSV color spaces and applies them to calculate the injury rate on fish.
To do these issues, the following steps are done. An original image is transformed into L*A*B and HSV color spaces. Achannel “a” is separated from L*A*B* color space. In channel a, a formula to adjust “channel a value” is proposed to realize the shapes of injury on fish clearly and a new channel a is obtained by adjusting the channel a. The new channel “a” is converted into injury binary image by manual threshold. Otsu’s method is applied converted the original channel a image of fish shape into binary image. Finally, by calculating the number of pixels of areas of shape and total injury of fish, the injury rate is calculated. The steps of image processing of HSV color space is similar to L*A*B* color space. The proposed process are tested on fish.
1 Introduction
“Machine vision”, as a crucial part of sorting systems, enables automatic and non-destructive selecting of products that satisfy certain requirements. There are many different methodologies for image processing in recent years. Therefore, choosing a right color space in processing algorithms is crucial. Eyarkai et al. described that mangoes were measured during ripening in 24 hours and evaluated using L*A*B* and RGB color coordinates [1].
Using exactly color space is important for controlling of food quality. Ivana et al. measured color of food products by using L*A*B* and RGB color space[2]. In this paper, fruit quality based on L*A*B* color space is more accurate than RGB color space. On the other hand, Hitesh et al. used image processing technique to detect fish disease [3]. This issue is done by using image processing algorithms based on L*A*B* and HSV color spaces. A method to measure injury rate of fish surface based on K-means clustering image segmentation was represented by Sheng el at.[4]. This method calculated injury rate based on S channel of HSV color space. After that, Otsu’s threshold was applied to converted S channel into binary image, and calculate injury rate by counting area pixels of injuries and total shape on fish. The results
*Corresponding author: kimsb@pknu.ac.kr
© The Authors, published by EDP Sciences. This is an open access article distributed under the terms of the Creative Commons Attribution License 4.0 (http://creativecommons.org/licenses/by/4.0/).
MATEC Web of Conferences 159, 02010 (2018) https://doi.org/10.1051/matecconf/201815902010 IJCAET & ISAMPE 2017