Part A
Part D Part B
Part C
Paper used:
0,15 mm - 130 gr
0,26 mm - 200 gr ("cardstock")
Glue: PVA
©
2008 Designed by L.Cherkashyn This cardmodel is only for personal and not for commercial use10 cm
10 cm
support for part B
A1 A1
A2
A2
A3 hole for B11
hole for B11
Page 2 Print on cardstock
10 cm
10 cm
A3
A4 A5
A5
A6
A6
A3 A1 A4
A5 A7 A6
A7a A7b
A7c
A7 A7
A7
A7
NOTE:
for correct superposition of supports A7 with part D glue assembled parts A5/A6/A7 onto A3 only after full assembling of Launch Pad
A1
©
2008 Designed by L.Cherkashyn This cardmodel is only for personal and not for commercial use10 cm
10 cm
B1
B2 B3
B4 B4
B5 B5
B6
B7
B6
B8
B8 B9
B10
B11 (D=4,5 mm)
B8
B7
1 3 2
4 5
6 1
2 3 4 5 6
12 12
3 3
4 4 12 12
3 3
4 4
B4
Tr left Tr right
B3 hole for B11
Page 4 Print on cardstock
B7
B7 rod for
assembling B8, B9 D=2 mm L =2,6 mm
B9a
Tr
B6 B6
©
2008 Designed by L.Cherkashyn This cardmodel is only for personal and not for commercial use10 cm
10 cm
C9a1
C9a2
C1
C2
C3 C4a
rod for assembling C3, C4 D=2 mm L =6 mm
C3a
C3b
C1a
C1b
C1
C1c
C1
C5 C5
C5a
C5b
C6
C7 C7
C8 C8
C9
C9 C6
rod for assembling C3, C9a,C9b
D=2 mm L =6,5 mm C9c
car truck
car truck
C1a
C1b C1b
C1c
C4
C4a
tabs for assembling of top and bottom parts of C3
C 3 o p ti o n
C5a C5a
D8
Page 5 Print on cardstock
C9a1
C9a2 C5
C5a1
C5a2
©
2008 Designed by L.Cherkashyn This cardmodel is only for personal and not for commercial use10 cm
10 cm
1 -glue tube w5 and supporting strips w6, 2 - glue w1 and w2
3 - assembly w3 and w4 then glue w3/w4 onto ledge w1/w2 4 - haft and glue wheels on w5
w5
w6
w1/w2 w1/w2
w3/w4 w6 w3/w4
w5
w6
w1/w2 w1/w2
w3/w4 w6 w3/w4
wheel pair
car trucks
Tr left
Tr right
Page 6 Print on cardstock
w1 w2
w3
w4 w6
w3/w4 w3/w4
w1 w2
w3
w4 w6
w3/w4 w3/w4
w5
w6
w1/w2 w1/w2
w3/w4 w6 w3/w4
w5
w6
w1/w2 w1/w2
w3/w4 w6 w3/w4
w5
w6
w1/w2 w1/w2
w3/w4 w6 w3/w4
w5
w6
w1/w2 w1/w2
w3/w4 w6 w3/w4
w5
w6
w1/w2 w1/w2
w3/w4 w6 w3/w4
w5
w6
w1/w2 w1/w2
w3/w4 w6 w3/w4
w1 w2
w3
w4 w6
w3/w4 w3/w4
w1 w2
w3
w4 w6
w3/w4 w3/w4
10 cm
10 cm
D1 D2
D3
D4
D5
D6 D6
D6 D6
D7 D7
D7
D7a D7a
D7a
D7b D7b
D7b
D7b D7b
D6a D6a
D6b D6b
D8 D8
D8a D8a
D8a D8a
D8b D8b
D9 D9
D9 D9a D9a
D9a D9a
D9a D9b D9b
D9b D9b
D9b
D7b D7b
assembling of D8 and C1 see next page
glue onto cardstock
hole for part a19 (see page 3 of Tsyklon-3 kit or page 6 of Tsyklon-4 kit)
glue on D3
D6
D5 D1
D2 D4 D3
D6aD6 D6b D7
D7
D5
D5 D
5
©
2008 Designed by L.Cherkashyn This cardmodel is only for personal and not for commercial use1 21 23 34 4
1 21 23 34 4
D8
D8
Part D Part C
Part B
Part A
D7
D1 - D4 D7
D9 D9
Page 8
C2
C1
C5
C5a C5b
C5a2 C5a1
b5 of Tsyklon kit
a4 of Tsyklon kit option
“Fuel lines”
Run two covered wires (d = 2 - 3 mm)
clamps from upper cutoff point of Tsyklon and bottom through
cutoff point.
Fix wires on bottom of part C.
