Technical Drawing Evaluation Form (TAHAP 1) - PCS FRIM

(1)

Furniture Segment : Solid Wood/ Panel Wood/ Metal / PP Type Of Furniture : Non-Domestic tables

Ref. Standard : BS EN 15372: 2016 – Furniture – Strength, durability and safety – Requirements for non-domestic tables.

Name/ Code Furniture :

Manufacturer :

Evaluation Panel : 1.

: 2.

: 3.

Date Received :

No. Criteria Remarks

Comply Not Comply w/

Notes 1 TECHNICAL DRAWING REQUIREMENTS

1.1 The furniture drawing must be attach along with technical drawing, exploded drawing and general specifications.

1.1.1 Technical drawing 1.1.2 Exploded drawing 1.1.3 General specifications

1.2 General dimension of the furniture must be stated clearly and each view (top, front, side) must have same following dimensions (units in mm).

2 SAFETY REQUIREMENTS

2.1 All components or parts of the tables, with which the user may come into contact, shall not have burrs/ sharp edges, nor shall there be open-ended tubes.

2.2 The safety distance between accessible movable parts is either more than 8mm or less than 25mm.

2.3 Al parts which are lubricated to assist sliding shall be designed to protect users from lubricant stains when in use.

3 COMMENT FOR IMPROVEMENT

(2)

We hereby approve based on this furniture technical drawing and specifications are complied with standard safety requirements and proceed to the next inspection.

Disclaimer:

This inspection is purposely for evaluating the general safety requirements from standard. Furniture results are depending on the accelerate testing and full furniture testing.

Panel Signatory 1 Panel Signatory 2 Panel Signatory 3

_________________________

Signature & Rubber Stamp ( )

_________________________

Completed Date :

(3)

Furniture Segment : Fabrik / PP Type Of Furniture : Chair

Ref. Standard : BS EN 1335-2: 2009: OFFICE FURNITURE - OFFICE WORK CHAIR – Non Domestic

Manufacturer :

: 2.

: 3.

Date Received :

No. Criteria Remarks

1.1 The furniture drawing must be attach along with:

2 SFETY REQUIREMENTS (Corners and edges, trapping, pinching and shearing) 2.1 Corners and edges, trapping, pinching and shearing

2.2 Safety distance of accessible movable parts must more than 8mm or less than 25mm

2.3 Accessible corners are rounded with minimum 2mm radius.

2.4 The edge of the seat, back rest and arm rest which are contact with the user are rounded with minimum 2mm radius.

2.5 All other edges are free from burrs and rounded or chamfered 2.6 End of hollow components are closed/ capped.

2.7 Moveable & adjustable parts shall be designed to avoid injury and inadvertent operation

2.8 All parts which are lubricated shall be designed to protect user from lubricant stains when normal use.

(4)

Disclaimer:

_________________________

Completed Date :

(5)

Furniture Segment : Solid Wood/ Panel Wood/ Metal / PP Type Of Furniture : Office Furniture – Work tables and desk

Ref. Standard : BS EN 572-3: 2002Office Furniture – Work tables and desk – Part 2:

Mechanical safety requirements.

Manufacturer :

: 2.

: 3.

Date Received :

No. Criteria Remarks

2.1 Supporting elements shall be so placed as not to restrict the movement of users.

2.2 Intermediate supporting elements under the work top shall either be visible or be placed where the risk injury to the user’s leg or feet is minimised. Intermediate supporting elements are

positioned less than 100mm or more than 450mm from the front edge of the table.

2.3 All edges and corners are free from burrs and rounded/

chamfered.

2.4 Edges and corners of the top surfaces are rounded with a radius not less than 2mm to avoid points of high pressure under the forearms.

2.5 The safety distance between accessible movable parts is either more than 8mm or less than 25mm. This applies to any elements moving relative to each other.

2.6 The handles are designed so that they cannot trap fingers during intended use.

2.7 The ends of feet and hollow components are closed/ capped.

(6)

Disclaimer:

This inspection is purposely for evaluating the general safety requirements from standard. Furniture results are depending on the accelerate testing and full furniture testing

.

_________________________

Completed Date :

(7)

Furniture Segment : Solid Wood/ Panel Wood/ Metal / PP Type Of Furniture : Office furniture-Storage

Ref. Standard : BS EN 14073-2: 2004 – Office Furniture – Storage Furniture – Part 2:

Safety Requirements Name/ Code Furniture :

Manufacturer :

: 2.

: 3.

Date Received :

No. Criteria Remarks

2.1 Accessible edges & corners are free from burrs and rounded/

chamfered. No open ended tubes.

2.2 Adjustable parts shall be such to prevent inadvertent operation/

release

(8)

Disclaimer:

_________________________

Completed Date :

(9)

Furniture Segment : Solid Wood/ Panel Wood/ Metal / PP Type Of Furniture : Single Beds

Ref. Standard : BS EN 1725: 1998 – Domestic furniture-Beds and mattresses – safety requirements and test methods.

Manufacturer :

: 2.

: 3.

Date Received :

No. Criteria Remarks

2.1 All components or parts of the bed, with which the user may come into contact, shall not have burrs/ sharp edges, nor shall there be open-ended tubes.

2.2 The safety distance between accessible movable parts is either more than 8mm or less than 25mm. This applies to any elements moving relative to each other.

2.3 When there is specific danger of feet being trapped by a moving part, the safety distance shall always below 100mm from the floor 3 COMMENT FOR IMPROVEMENT

(10)

Disclaimer:

_________________________

Completed Date :

(11)

Furniture Segment : Solid Wood/ Panel Wood/ Fabrik / PP Type Of Furniture : Chair / Table

Ref. Standard : BS EN 1729-2: 2012: Furniture – chairs and tables for educational institutions – Part 2: Safety requirements and test method (Chair size mark: 5)

Manufacturer :

: 2.

: 3.

Date Received :

No. Criteria Remarks

1.1.1 Technical drawing.

1.1.2 Exploded drawing.

1.1.3 General specifications.

2.1 The edge of the seat, back rest and arm rest which are contact with the user are rounded with minimum 2mm radius.

2.2 All other edges and corners with which the user may come into contact with during normal use shall be smooth, rounded or chamfered and shall have no burrs.

2.3 With the exception of setting up or folding tables and chairs, there shall no accessible gaps always be either more than 8mm and less than 25mm.

2.4 Parts shall not be detachable without use of an appropriate tools.

3 COMMENT FOR IMPROVEMENT

(12)

Disclaimer:

_________________________

Completed Date :