• Tidak ada hasil yang ditemukan

DOC Preparation of Manuscript for Tiees-98

N/A
N/A
Protected

Academic year: 2024

Membagikan "DOC Preparation of Manuscript for Tiees-98"

Copied!
2
0
0

Teks penuh

(1)

International Conference on Mechanical, Industrial and Energy Engineering 2016 26-27 December, 2016, Khulna, BANGLADESH

MIE16-001[paper number; will be assigned by Conference Secretariat]

Title of the paper [Times New Roman, Size 12, bold]

(A 10pt line space)

Mohammad Mashud 1,*, Akira Umemura 2 [Times New Roman, size10, Italic]

1 Department of Mechanical Engineering, Khulna University of Engineering & Technology, Khulna-9203, BANGLADESH

2 Department of Aerospace Engineering, Nagoya University, Nagoya, JAPAN [Times New Roman, size10]

(Two lines space with 10 pt) ABSTRACT

The abstract should clearly be stated the objectives, methodology, results and conclusions within 150 words.

(A 10pt line space)

Keywords: Please write three to five keywords in the center.

(Two lines space with 10 pt)

* Corresponding author. Tel.: +88-01713255226 E-mail address: [email protected]

(2)

International Conference on Mechanical, Industrial and Energy Engineering 2016 26-27 December, 2016, Khulna, BANGLADESH 1. Introduction (Top

heading should be in bold)

The overall length of the paper, including figures and tables, must be limited to 6 pages only.

The main text should be written in two-columns format with a font of 10 pt Times New Roman.

The interval of columns should be 10 mm. This MS-Word document can be used as a template.

When the paper is ready, make a pdf file with 600 dpi resolution and save the file as paper-number.pdf (For

example MIE10-

001.pdf). Then be sure to verify that you can correctly view your pdf file with an English version of the pdf viewer. The size of the pdf file should be less than 2.0 MB.

(A 10pt line space) 2. Paper size and Margins

2.1 Paper size A4 paper 2.2 Margins

Top : 25 mm, Bottom : 25 mm

Left : 20 mm, Right : 20 mm

3. Format

Manuscripts should consist of the title, author(s), author’s affiliation and address, abstract, keywords, and main text. Title, author(s), author’s affiliation and address, abstract and keywords should be written according to the format given above.

3.1 Main text

Main text should begin at two lines bellow keywords.

3.2 Heading

Examples of heading are as follows.

2. Experimental setup/Numerical Experimental setup is shown in Fig.1. ....

(A 10pt line space) 2.1 Temperature measurement

(A 10pt line space) (1) Mount of thermocouples

Thermocouples were inserted in capillary tubes ...

3.3 Equations

Equations and symbols should be written with 10pt italic font except super/sub scripts. There should be one line space upper and lower equation. In the main text, an equation is explained as Eq.(1).

(A 10pt line space)

0

 

y v x u

(1)

(A 10pt line space) 3.4 Figures, tables, pictures

Keep margins. Figures, tables, and photos should be explained in

main text as

Fig.1,Table 1,Photo 1.

(A 10pt line space)

(A 10pt line space) Fig.1 Experimental

setup.

(A 10pt line space)

(A 10pt line space) Fig.2 Heat transfer coefficient of R22 for

evaporation (A 10pt line space) Table 1 Historical data

of vapor pressure of ammonia.

Author Year T

Keyes 1918 240-398

Cragoe 1920 195-343 McKelvey 1923 195-195 Beattie 1930 303-405 Overstreet 1937 176-242

(a 10pt line space) 3.5 References

References should be indicated by [1], [2, 3], [4-7], and be listed at the end of manuscript.

4. How to submit your manuscript

Please send your manuscript in PDF format to Conference Secretariat:

[email protected] m. Please also send a copy of your manuscript to

[email protected] m.

5. Deadline

Will be notified later.

6. Registration

Registration of

presenting author is obligatory to include his or her paper(s) to the official program of the conference. All the presenting authors are requested to send their registration form by

post, e-mail or fax to conference secretariat before the announced date.

(a 10pt line space)

NOMENCLAT URE

cp

F G h p T t V

: specific heat at constant pressure, kJ : Helmholtz function, kJ

: Gibbs function, kJ : specific enthalpy, kJ・kg-1 : pressure, kPa

: temperature, K

: Celsius temperature, oC : volume, m3

(a 10pt line space) REFERENCES [1] Miyara, Flow

dynamics and heat transfer of wavy condensate film, Journal of Heat Transfer, Trans. of ASME, Vol. 123, pp 492-500 (2001).

[2] T. Nosoko, A.

Miyara, The

evolution and subsequent dynamics of waves on a vertically falling liquid film, Physics of Fluids, Vol. 16, pp 11180- 1126, (2004).

* Corresponding author. Tel.: +88-01713255226 E-mail address: [email protected]

Referensi

Dokumen terkait

In the following table and figures, the average tensile, flexural and impact strengths of the manufactured composite is compared to the properties of a coir fiber reinforced epoxy

Yan and Song [5] studied the effect of face sheet thickness on aluminum foam core based sandwich structure and found that the increase in facing thickness causes higher load carrying

Thus the consumer gets to adjust the amount of electricity consumed from grid and any excess electricity after self-consumption that is produced by rooftop solar system or any other

CFD analysis of different fluids and different pipe materials were investigated on parallel and counter flow in concentric tube heat exchanger [6].. The first stage was a modified

In pursuit of this, we have considered using binary refrigerant mixtures instead of a single refrigerant in the VCRS - the aim was to solve the Peng-Robinson equation of state [8] using

Method: Fig.01: Overview of the study 2.1 Lean six sigma: Lean Six Sigma is amethodology that relies on a collaborative team effort to improve performance by systematically removing

The internal resistance of MCFs with substrate orange potato and grass are respectively 787Ω, 848 Ω and 943Ω.The maximum voltage obtained from the MFCs is respectively 517mV, 454mV and

Accordingly, Elbashbeshy and Bazid [1] presented an exact similarity solution for unsteady momentum and heat transfer flow whose motion is caused solely by the linear stretching of a