This is to certify that this project and thesis entitled ―RFID Based Door Lock with Automatic Open and Close Door‖ was done by the following students under my direct supervision and this work was done by them in the Department of Electrical and Engineering laboratories Electronics at the Faculty of Engineering of Daffodil International University in partial fulfillment of the requirements for the degree of Bachelor of Science in Electrical and Electronics Engineering. Abul Kalam Azad, ID No Session: Fall 2015 has been accepted as satisfactory in partial fulfillment of the requirements for the degree of Bachelor of Science in Electrical and Electronics Engineering in December 2018.
ACKNOWLEDGEMENT
ABSTRACT
INTRODUCTION
- Introduction
- Problem Definition
- Existing Solution
- Proposed Solution
- Problem Statement
- Objectives
- Scopes
- Research Methodology
- Project Outline
- is the background of the project. In this chapter reviews of some related works on RFID based door lock with automatic door open and close
- is the Description of components where describe the all components that are used in the project
- is the Analysis and simulation of the project that is illustrates the proposed solution for visually impaired people with the block diagram and flowchart. Also in this chapter
- is the Conclusions. In this chapter we discuss about the conclusion, limitation of the project and future work of the project
The moment this information matches the information stored in the microcontroller's database, the individual gets the expert to enter the anchored area. The power status of the individual is also displayed on the LCD screen associated with the microcontroller. Since the goal of the entire project is to simplify use, it would be unreasonable to propose to them a technologically advanced tool.
There should also be a user manual that explains the functionalities of the device and provides training lessons on how to use it. While the device is dependent on the use of the user to provide power to the system, the overall power consumption of the device during its operation should be low. The field created is called a relentless wave, and in view of the way the nature of the field decreases with the square of the division, the peruses must use a somewhat broad force.
That field overwhelms any response a marker can give, so along these lines names answer to side channels found directly below or more the repetition of the steady wave. In this chapter we discuss about the conclusion, limitation of the project and future work of the project.
LITERATURE REVIEWS
Introduction
Initially, RFID names were provided to supplant institutionalized identifying evidence in supply chains in the long term. Their positive conditions are that they can be scrutinized from a distance and without a discernible path, contain a greater amount of information than institutionalized distinguishing evidence, and are logically overwhelming. The paper maps possible strikes that can ignore one's insurance, and it likewise shows countermeasures.
The paper furthermore presents stream queries for what is based on finding and tracking the moving controlled item. Since the uses for RFID tags are so comprehensive, there is a colossal desire to reduce the costs of producing them.
Summary of the chapter
By printing labels, it is possible to destroy the cost-intensive collection of two basic segments, receiver wire and chips. Radio Frequency Identification - AM The article concludes by looking at some of the social implications caused by RFID.
DESCRIPTION OF COMPONENTS
- Introduction
- Arduino Boards
- Purpose of Arduino Boards
- Features of Arduino Boards
- KB SRAM, 32KB flash
- The Arduino Uno
- Arduino Uno Technical Specifications
- Pin diagram of Arduino UNO R-3
- Short description of the pins
- RFID RC 522 Module
- RFID RC 522 Module Pin Configuration
- RFID RC-522 Module Features
- Working Principal of RFID RC-522 Module
- Why use an RFID RC-522 Module?
- Buzzer
- Applications for Buzzers
- Types of LED
- Switch
- MOSFET
- Transistor
- Capacitor
- PIC 16F877 Microcontroller
- LCD Display
- Resistor
- Diode
- Printed circuit board
- RFID Card
- Summary of the chapter
It contains both a microcontroller and a piece of the item or Incorporated Improvement Condition (IDE) that continues to run on your (PC), used to create and exchange PC code with the physical board. The mezzanine of an Arduino has ultimately proven to be a great solution degree celebrated, where organizers or students simply start constructions, and for an astonishing reason. Unlike most previous programmable circuit schemes, the Arduino in no way requires an alternate device to program another code on the board. You can simply use a USB connection. In addition, the Arduino IDE uses a key version of C++, which makes it easier to enter the program.
Finally, the Arduino board offers a common case problem that breaks down the components of the microcontroller into a very accessible package. Instructors and undergraduates in schools use it to produce logical devices with minimal effort to confirm the standards of materials science and science. The Uno board is the first in a development of USB Arduino sheets and the reference appears for the Arduino agreement with; for a comprehensive list of current, past, or obsolete sheets, see the Arduino sheets inbox.
RFID RC-522Module is the high-coordinated RFID card user that takes a shot at non-contact 13.56 mhz correspondence, is planned by NXP as a low power utilization, minimal effort and reduced size reading and assembly chip, is the best decision in the improvement from smart meters and compact handheld devices. A metal oxide field effect transistor (FET) where the voltage selects the conductivity of the contraption. The ability to change conductivity in proportion to associated voltage can be used for upgrading or trading electronic tokens.
A voltage or current connected to one set of transistor terminals changes the current through another combination of terminals. The main drawback that could be offset is that it doesn't have an internal clock source like most to a large extent compared to other logic current PICs. In any case, using an external check, if all else fails, results in a faster effort, as you can choose a 20MHz gain stone instead of the usual 8MHz internal oscillator.
A 16x2 LCD shows that it is an extremely central module and is commonly used in various devices and circuits. A diode has low (in a perfect world zero) resistance in one direction, and high (preferably infinite) resistance in the other direction. The 'front' side of the board will have printed part data, for example, resistance and resistance, diode type and edge, and so on.
The RFID card is an EEPROM memory chip, which can store data in memory. Then the RFID card chip is activated and sends the data stored on the RFID card.
ANALYSIS AN SIMULATION
Introduction
Block diagram of the project
Display
Proposed circuit design
The structure model of the whole enterprise was completed after the equipment was implemented. We have built the circuit to reactivate the enterprise using Proteus v7.8 which is shown in Fig. . It has ISIS which is used for circuit structuring with reconstruction and ARES which is used for PCB planning [16].
ISIS is a product used to draw schematics and visualize circuits in real time. It has an element of seeing the yield in a 3D perspective of the structured printed circuit next to the parts. It is embedded with footprints of various classes of parts such as ICs, transistors, headers, connectors and other discrete parts.
Proteus is the simplest and most fundamental programming with the latest innovation for circuit performance and recreation. By counting essential parts and comparing data from the library, it is usually recreated after the circuit is set up. We use this product because it is extremely easy to use to structure and recreate circuits than other software.
The gears used for the structure and execution of the accompanying circuit are Arduino Uno R3, ultrasonic sensor, bell, red movement, blue movement, green movement, pot-hg and virtual terminal.
Hardware Design
Summary of the chapter
RESULT AND DISCUSSION
Introduction
Result
In addition, any questions about this idea or passphrase based login lockout framework, when we see the modern board system(s) login, the sticker price hit quickly along with the service obviously. That's the way we started building this venture, and we're extremely pleased with the way it finally looks.
Summary of the chapter
CONCLUSIONS
Conclusion
Limitation of the Study
Future Scopes of the Work
Appendix
Programming Code uses in the ATMEL 328 Microcontroller
