Read this instruction manual attentively and keep this operating handbook well for future reference uses
INSTRUCTION MANUAL
ENGLISH
PACKING LIST
RES-ED440H-W
RES-ED450H-W
RES-ED480H-W
RES-ED4100H-W
CORPORATION
ELECTRIC STORAGE WATER HEATER
RIT-0003-154
NO. NAME UNIT (Pcs)
1 1
2 1
3
4
5
2
1
2
Electric Water Heater Instruction Manual Hanging Bolt Pressure Relief Valve Hook
012313
Indonesia
CATALOG
Troubleshooting
Before Use...1
Product’s Features...1
Part Names...2
Specification...3
Dimension...3
Installation...4~6
Installation Notice...6
Operating Instructions...7
Daily and Common Maintenance...7
Electrical Diagram...8
Troubleshooting...9
Packing List ...Back Cover
Problem Causes Remedy Methods
I n d i c a t o r l a m p n o t lighting
No hot water coming out
Water leakage from tank
ELCB can’t reset
1. No power or power plug is not connected well
2. Too low temperature adjustment
3. ELCB not yet switch on Switch on the ELCB
4. The interior wire material damaged
5. Indicator lamp damaged
6. Heating element damaged
7. Water is over heated
1. Deficient heating time.
3. Temperature-controller malfunction
4. Heating element damaged
1. Water tap is turned off
2. Water pressure is too low
3. Pipe connection is not connected properly
1. The various mouth’s connection are not hermetically sealed
2. The tank leakage
1. ELCB damaged
2. Electric leakage 2. Mix water valve for hot
water too low
Keep on heating
Adjust the mixed water valve for hot water to be high.
Request to After Sales Service for repair.
Request to After Sales Service for repair.
Request to After Sales Service for repair. Request to After Sales Service for repair.
Check electricity source and fixing plug must be good.
Adjust the temperature control to be the highest temperature.
Turn on the water tap
Add water pump
Correctly connect it according to diagram’s requirements
2
Operating Instructions
lTo start using, open the tap at heater outlet and then inlet valve to fill in the tank, when the tank fulfilled, water will come steadily out of the tap. Close the outlet tap now.
lPlug in the power supply and press reset of the ELCB switch till indicator goes on.
lTurn on power knob and select which wattage will use (500W, 1000W, 1500W selectable).
lSelect maximal water temperature with turn temperature knob clockwise to low, medium or high temperature. (if after selected max water temperature the lamp indicator not goes on please select water temperature to be higher).
lHot water operations: After the electrical water heater normally works and the heats for a long period of time, you can use the hot water in the tank, you need mixed water valve to mixing hot water and cold water, as your proper temperature after finishing uses, shut off the mixed water valve.
Cautions:
ØWhen adjusting the water temperature of the water exiting mouth, the shower must not spray directly to the human body; you should test the water temperature first to avoid burning or damages.
ØTemperature setting: According to your required temperature, rotate the temperature adjusting knob by the clockwise direction. You can select to use the heating temperatures with grades in the temperature ranges of thirty to seventy five degrees Celsius from closing to the low, medium and high bands or from low to high.
ØPower selecting: This unit offers three power band for your selections. Band 1: 500W, Band 2 : 1000W, Band 3 : 1500W.
7
Part Names
lFrequently checking the connection of power source’s plug and the outlet is in good condition. The plug’s outlet is well connected the ground or not.
lWhen it isn’t operated for a long period of time, typically in the low temperature zones, you must empty the tank to avoid the water freeze in the tank which will cause the tank damage.
lIn order to assure the electrical water heater work with high efficiency, you had better clean the heating parts once a year. Remove the water dirt’s deposits accumulated on the electrical heating parts and the tank base.
Daily and Common Maintenance
Machine body
Hot water outlet pipe
Power source wire with electricity leakage protection
Drainage pipe joint Temperature selector switch Temperature
indicator Indicator lamp
Wattage Selector Switch
Electrical Diagram
Before Use
Thank you for using Rinnai electric storage water heater .
We would like to invite you to read this manual carefully before using and pay attention to the security characteristics and installation instructions especially.
Keep this instruction manual well for future reference.
1.
lReliable heating element advanced stainless heater, with electricity leakage protection device.
lAutomatic over temperature protection device and over pressure protection device.
2. Durable:
lAdvanced durable outer shell.
lTank with titanium enameled, good toughness, high strength, prolong its life.
3. Energy saving:
lUltra thick, micro hole polyurethane foaming technique, superior thermal retardation, power/energy saving.
4. Convenience:
l Adjustable heating temperature between 30 - 80 . lThree power selection (500W, 1000W, 1500W).
5. Multifunction:
lClosed structure, can provide hot water for toilet, kitchen and other places.
l For families, companies, hotel, beauty parlor and other service places. lThis heaters are advanced style of our product, so please refer to the
manual to use it. Safe:
0 0C
Product's Features
Power Selection Thermostat
Element Element
Indicator lamp Thermo
Breaker
ELCB
L
N
RES-ED440H-W RES-ED450H-W RES-ED480H-W
500W, 1000W, 1500W (Selectable)
220V ~ 10A
> 90 %
Hermetical type water storage style
Horizontal
lThe water inlet and outlet pipe should not be connected in reverse.
lThe wall where electric water heater hang on should be firm, and can hold two times as the weight of the electric water heater fully filled with water.
Security caution:
lIn order to prevent accident, only use the accessories our company offer and couldn't changed or replace without any notice.
lIf the accessory is damaged, should be notify our after sales service department to maintain and replace with the accessories our company offer.
lIf don't comply to above items and cause some accident, our company won't hold any responsibilities to the direct loss or indirect caused by that.
lThe power plug must be properly grounded and it is prohibited to use the tap water pipe line as grounding. In the power plug, the nul line shall not be connected the ground wire. To prevent electric shock, the ground wire shall not be electrified.
Installation Notice
RES-ED440H-W RES-ED450H-W RES-ED480H-W RES-ED4100H-W
MODEL
100 100 100 100
430
Hot water outlet Cold water inlet
Power source wire
Water inlet valve Shower
(Note: Thisinstallation is only for indicating diagramreference).
lConnect the drainage pipe with pressure relief valve, (refer to diagram 4), connect the other end of the drainage pipe with drainage mouth to avoid the room becomes dirty. It may exist water drops fall down at the pressure relief mouth sector when water heater is operating and heating the water, this is normal because of the water in the tank expanding when heated. In any conditions, this pressure relief hole must not be blocked. You can drain the drops to drainage, the drainage pipe connecting with pressure relief valve should be installed facing down.
lConfirm proper position, fix the shower hand hanger on the wall, connect the shower hand tube into pipe line.
lTurn on the mix-water valve connected with electric water heater and rotate to water outlet pipe direction (left), then turn on tap water valve, filling tank. It indicates the tank is fully filled with water when the water flow out from water outlet mouth continuously, then close the mix-water valve. Check whether every connection joint is leaking or not.
lPlug the power source when tank is fully filled with water, there is no leakage and electricity meet the requirement.
lIf want to distribute the hot water to many outlet, you can refer to diagram 5.
lUsage of mixed water valve:
Connection: Add seal to screw cap of pull to down is smaller.
Turn left and right to adjust the water valve of cold water
inlet
lInstall the pressure relief valve and other accessories refer to diagram 2. Use seal to avoid water leakage.
lWe suggest to install extra G1/2” nut in the proper position of water inlet and outlet pipes in order to install and knock down easily. Confirm the position where need water, connect the cold water outlet pipe and hot water outlet pipe respectively.
Note: the pipes of electric water heater should be not too long to reduce heat losses.
lInstallation refer to diagram 2. This diagram is an installation sketch, the specification is according to user's circumstance.
lThe electric water heater must be installed by professional of our after sales service department or installed by qualified technician.
lInstalling way is hanging on the walls.
lSelect proper height and position, then determine the installation position at the same level.
lDrill two corresponding holes with distance as diagram 1, then insert the bolts and firmly fixed, hang the electrical water heater lastly.
lNote: the direction of hanging bolt must be installed correctly, perpendicular to ground and face up, shouldn't slantwise.
lConfirm whether it already fixed firmly or not.
Installation
Hot water outlet pipe
Mono-directional security valve
Baca buku petunjuk ini dengan seksama dan simpan dengan baik sebagai referensi dimasa yang akan datang
INDONESIA
NO. Nama Unit (Pcs)
1 1
1
3
4
2
1
Electric Water Heater Petunjuk Penggunaan Baut Gantungan
Pressure Relief Valve
ELECTRIC STORAGE WATER HEATER
PETUNJUK PENGGUNAAN
DAFTAR PACKING
2
5 Hook 2
RIT-0003-157
RES-ED440H-W
RES-ED450H-W
RES-ED480H-W
RES-ED4100H-W
PT. BAHAGIA INTI TAMA Jakarta - Indonesia
DAFTAR ISI
Cara Mengatasi Masalah
Sebelum Menggunakan...1
Fitur Produk...1
Nama Bagian...2
Spesifikasi...3
Dimensi...3
Pemasangan...4~6
Catatan Saat Pemasangan...6
Petunjuk Penggunaan...7
Perawatan Rutin Harian...7
Diagram Listrik...8
Cara Mengatasi Masalah...9
Daftar Packing...Cover Belakang
Masalah Penyebab Cara Mengatasi
Lampu indicator tidak menyala
Air panas tidak keluar
Air bocor dari tangki
ELCB tidak bisa me-reset
1. Tidak ada aliran listrik atau pemasangan steker listik kurang sempurna.
2. Pengaturan suhu terlalu rendah
3. ELCB belum dinyalakan Nyalakan ELCB
4. Ada kabel yang putus
5. Indicator lampu rusak
6. Heating element rusak
7. Temperatur air telalu panas
1. Waktu pemanasan kurang.
3. Temperature-control tidak berfungsi
4. Heating element rusak
1. Kran air belum dibuka
2. Tekanan air terlalu rendah
3. Sambungan pipa tidak tersambung dengan benar
1. Seal sambungan tidak rapat
2. Tangki bocor
1. ELCB rusak
2. Ada kebocoran listrik 2. Bukaan kran pencampur
untuk air panas terlalu kecil.
Panaskan kembali
Atur bukaan kran pencampur untuk air panas lebih besar lagi H u b u n g i L a y a n a n Purna Jual kami
H u b u n g i L a y a n a n Purna Jual kami.
H u b u n g i L a y a n a n Purna Jual kami. H u b u n g i L a y a n a n Purna Jual kami.
Periksa aliran listrik dan p e r b a i k i p e m a s a n g a n steker ke stop kontak Atur temperature control kesuhu yang lebih tinggi lagi.
Buka kran air
Gunakan pompa air
Perbaiki sambungan pipa sesuai dengan diagram.
Sambungan pipa diseal dengan rapat
2
Petunjuk Penggunaan
lUntuk memulai penggunaan, buka kran air panas lalu buka kran air masuk ke pemanas, biarkan air terus mengalir, saat tangki sudah penuh, air akan keluar dari kran air panas dan tutup kran air panas.
lPasang steker listrik dan tekan tombol reset yang terdapat pada ELCB dan lampu indicator pada ELCB akan menyala.
lPutar tombol power dan pilih watt (daya listrik) yang akan kita gunakan (500W, 1000W, 1500W dapat diatur/dipilih).
lPilih suhu maksimal air dengan memutar tombol pengatur suhu searah jarum jam ke posisi low, medium dan high temperature (bila setelah memilih suhu air maksimal lampu indicator pada water heater tidak menyala, silakan pilih suhu air lebih tinggi lagi).
lPengoperasian air panas: Setelah water heater bekerja normal dan air sudah dipanaskan pada waktu yang lama (sampai lampu indikator water heater padam). Air panas dapat digunakan dengan menggunakan kran mixing untuk mencampur air panas dan dingin sesuai dengan yang kita inginkan. Setelah digunakan tutup kembali kran mixing.
Perhatian:
ØSaat mengatur suhu air jangan sampai shower langsung mengenai tubuh kita, pertama kita harus mencoba suhu air untuk mencegah kulit terbakar.
ØTemperatur setting: Sesuai yang anda inginkan, putar tombol pengatur searah jarum jam, anda dapat memilih dengan cakupan
dari 30 - 75
ØPemilihan daya listrik: Water heater ini menawarkan 3 pilihan daya listrik yang dapat dipilih: 500W, 100W, dan 1500W.
e suhu
suhu suhu
0 0
suhu C dari off ke low, medium dan high, atau dari low ke high.
7
Nama Bagian
lPeriksa sambungan listrik secara berkala, apakah sambungan dalam kondisi baik, steker listrik tersambung dengan ground atau tidak.
lKetika water heater tidak dipergunakan dalam waktu yang lama, khususnya didaerah yang nya rendah, untuk menghindari air membeku didalam tangki yang akan menyebabkan kerusakan pada tangki, setelah selesai digunakan air didalam tangki harus dikosongkan.
lUntuk menjaga elektrik water heater bekerja dengan efesiensi yang tinggi, sebainya heating element dibersihkan setahun sekali, bersihkan kotoran dari endapan air kotor yang menempel diheating element dan permukaan tangki.
suhu
Perawatan Rutin Harian
Steker listrik dengan pencegah
kebocoran listrik
Pressure-relief valve
Saluran pembuangan
Tombol pengatur suhu Tombol pengatur watt
Lampu indikator Body mesin
Pipa air panas
Steker
Diagram Listrik
Sebelum Menggunakan
Kami ucapkan terima kasih anda telah menggunakan storage water heater listrik Rinnai.
Kami mohon anda untuk membaca manual ini secara seksama sebelum anda menggunakan produk storage water heater listrik ini. Mohon untuk memberi perhatian pada karakteristik keamanan serta pada cara pemasangan. Dan simpan dengan baik buku petunjuk penggunaan ini, sebagai referensi dimasa yang akan datang.
1. Aman:
lElemen pemanas yang bagus dengan fitur anti kebocoran listrik.
lPerlindungan dari suhu yang terlalu tinggi, serta perlindungan dari tekanan yang berlebihan.
2. Daya tahan:
lBagian luar water heater yang kuat dan tahan lama.
lTangki terbuat dari enamel titanium yang kuat serta usia pakai yang panjang.
3. Hemat Energi:
lLapisan polyurethane yang tebal dengan daya sekat panas yang baik dan hemat energi.
lDilengkapi reservasi mode dengan dua periode ON dan OFF sehingga dapat menghemat energi.
4. Kenyamanan:
l Pengaturan suhu pemanas pada range 30 - 80 .
6. Multifungsi:
lStruktur tertutup bisa memberikan air panas untuk toilet, dapur maupun tempat lainnya.
l Untuk keluarga, perusahaan, hotel, salon kecantikan serta tempat jasa lainnya.
lPemanas air ini merupakan model yang canggih, jadi mohon untuk membaca buku petunjuk dengan seksama untuk menggunakannya.
0 0C
Fitur Produk
Power Selection Thermostat
Element Element
Indicator lamp Thermo
Breaker
ELCB
L
N
40L
500W, 1000W, 1500W (dapat diatur)
220V ~ 10A
> 90 %
Hermetical type water storage style
Horizontal
Energi yang hilang dalam 24 (kWh)
IPX4
Spesifikasi
6
Dimension
Dimensi
lPemasangan pipa air panas dan dingin jangan sampai terbalik.
lDinding untuk menggantung water heater harus kokoh dan sanggup menahan dua kali berat water heater saat penuh berisi air.
Perhatian untuk keamanan:
lUntuk mencegah terjadinya kecelakaan, gunakan hanya aksesories yang disediakan oleh perusahaan kami, dan tidak bisa dirubah atau diganti tanpa pemberitahuan.
lJika aksesories rusak, harus menghubungi layanan purna jual kami untuk mendapatkan aksesories yang kami sediakan.
lKami tidak akan bertanggung jawab atas kecelakaan yang terjadi sebagai akibat jika tidak memenuhi aturan diatas, serta semua kerugian langsung maupun tidak langsung yang diakibatkannnya.
lS t e k e r l i s t r i k h a r u s m e m i l i k i g r o u n d y a n g b a i k d a n d i l a r a n g menghubungkan ground ke pipa air, pada stop kontak line nul jangan dihubungkan dengan grounding. Untuk menghindari sengatan listrik kabel ground jangan dialiri listrik.
Catatan Saat Pemasangan
Body mesin
Koneksi ke pipa air panas
Pipa air panas Pipa air dingin
Steker listrik
RES-ED440H-W RES-ED450H-W RES-ED480H-W RES-ED4100H-W
RES-ED440H-W RES-ED450H-W RES-ED480H-W RES-ED4100H-W
MODEL
100 100 100 100
lHubungkan pressure relief valve dengan pipa pembuangan (lihat diagram 4), hubungkan pipa pembuangan dengan lubang pada kran agar ruangan tidak kotor. Mungkin ada tetesan air pada lubang buang kran, saat pemanas dinyalakan dan mulai memanaskan air. Itu adalah proses yang normal karena air yang ada didalam tangki mengembang saat dipanaskan. Pada kondisi apapun, saluran pembuangan dari kran ini tidak boleh tertutup dan harus dipasang menghadap ke bawah.
lSetelah posisi benar, pasang shower dan hubungkan dengan pipa air.
lBuka kran air panas dan buka kran air dingin untuk mengisi air ke water heater. Ketika air sudah mulai keluar dari kran air panas, tutup kran dan perhatikan apakah ada kebocoran.
lHubungkan koneksi listrik ketika water heater sudah terisi penuh dengan air, dan sudah tidak ada kebocoran serta listrik sudah sesuai yang dibutuhkan.
lJika menginginkan air panas untuk beberapa titik, silahkan mengacu pada diagram 5.
lPenggunaan kran mixing
Koneksi: Tambahkan packing pada kedua pipa air, hubungkan dengan kran (lihat diagram 2 dan 3) pastikan tidak ada kebocoran. P e n g g u n a a n : S e t e l a h s e m u a terhubung sesuai dengan diagram, gerakan tuas kran naik dan turun diagram 2. Gunakan seal untuk mencegah kebocoran.
lKami sarankan menggunakan water mur G1/2" tambahan pada pipa air masuk dan keluar, untuk memudahkan pemasangan dan pada saat membuka. Tentukan posisi untuk air serta hubungkan pipa air dingin dan air panas. Catatan: Usahakan agar pipa air panas tidak terlalu panjang agar tidak kehilangan banyak panas.
lPemasangan mengacu pada diagram 2. Diagram ini adalah sketsa pemasangan, untuk spesifikasi tergantung pada masing-masing pengguna. lWater heater ini harus dipasang oleh tenaga terlatih
atau orang yang ditunjuk oleh servis center kami. lPemasangan dengan cara digantung ditembok. lPilih ketinggian serta posisi yang cocok dan
pastikan pada posisi yang rata.
lBor dua lubang yang sesuai dengan jarak seperti d i a g r a m 1 , m a s u k a n b a u t d a n k e n c a n g k a n , kemudian gantungkan water heater.
lPerhatikan: arah gantungan harus dipasang dengan benar, tegak lurus terhadap lantai dan tidak boleh
(Catatan: Instalasi ini adalah sebagai diagram petunjuk untuk
Koneksi ke pipa air dingin Kran mixing
Koneksi ke pipa air panas
Shower
Steker listrik dengan pencegahan