LKS 2017 TP16 XXIV HD EN

(1)

Test Project for skill 16 LKS_2017_TP16_XXV_HD_EN

Version:1.0 Date:20.10.2016

1 of 12

www.inaskills-electronics.com

Hardware Design

Test Project document

LKS_2017_TP16_XXV_HD_EN

Submitted by:

Name : ASC WSC Team

Member : Ina skills Electronics

Type : Close Project

(2)

2 of 12

Point : 25 Points

Description of project and tasks

a. Circuit Design and Schematic Capture (Time limit: 2 hrs, 1st day)

You are to complete 4 designs. Please complete the designs according to the

requirements. Use only components from the parts list for your designs. You may not

need all the components in the parts list. Competitors can’t use simulation tool.

Competitors can read component data sheet that is provided with only personal

computer which contains Data sheet pack. The data sheet pack should be provided

by Committee. The hard copies brought by competitor can’t be used, but competitors

can read the hard copies provided with committee. When you have completed your

designs you are to submit your answers on the provided Answer Sheets to the expert.

You cannot do this until the 1st hour has passed. You will then be given the schematic

solution for schematic entry into Altium. You cannot start your PCB design in this

phase of the test project.

b. Design of Printed Circuit Board (Time limit: 2 hrs)

Design printed circuit board of PCB using Altium Designer CAD tool.

Complete the designs, save PCB Gerber file in the Network Drive

Please use track widths of 0.4 mm minimum for signal and 0.7 mm minimum for power

and a clearance of 0.3mm minimum

Minimum pad size

Type Ukuran pada Pad Ukuran Lubang Bor

IC DIP 1.5 mm 0.8mm

Resistor 1.8 mm 0.8mm

(3)

3 of 12

Header T Block 2 mm 1.2 mm

Board dimension of 100 x 160 +/- 0.2mm is to be used

You are to place the components following request jury

c.

Build and Test Hardware design project (Time limit: 2.0 Hr)

 Assemble PCB, and check its operation.

 Completing the project, submit all the product and documents.

Instructions to the competitor

The task in this project is to design and make an electronic thermometer using the

integrated circuit LM234 to run and control the speed of a motor, which can be used as a

cooling system of any devices. Below 40ºC the motor is off, when the temperature exceeds

40ºC the motor starts running. As the temperature rises the speed of the motor increases.

Buzzer on if temperature more then 100ºC. Moreover, the temperature is to be shown by a

[image:3.595.85.523.380.634.2]

LED indicator and seven segment (from 0ºC to 100ºC).

(4)

4 of 12

Parts List

No.

Qty.

Value / Tipe Part

Information

1

R. 68 Ohm

Resistor ¼ W 1%

2

11

R. 220 Ohm

Resistor ¼ W 1%

3

7

R. 330 Ohm

Resistor ¼ W 1%

4

12

R. 1K Ohm

Resistor ¼ W 1%

5

1

R. 10K Ohm

Resistor ¼ W 1%

6

2

R. 12K Ohm

Resistor ¼ W 1%

7

1

R. 15K Ohm

Resistor ¼ W 1%

8

1

R. 18K Ohm

Resistor ¼ W 1%

9

2

R. 20K Ohm

Resistor ¼ W 1%

10

C. 100 nF

Capasitor MKM

11

1

C. 4,7 uF

Capasitor Electrolit

12

1

C. 6,8 uF

13

1

C. 10 uF

14

2

C. 100 uF

15

1

D. 1N4007

Dioda 1 Ampere

16

1

Tr. C9013

Transistor NPN

17

1

Tr. TIP 41C

Transistor NPN

18

10

Led. Red 3mm

Led Red 3mm

19

1

Led. Green 3mm

Led Green 3mm

20

1

Ds. 7 Seg. 41056

Seven Segment CA 0,56”

21

1

Ic. Ne 555

IC Pulse Generator

22

1

Ic. SN 74LS04

IC Gate Not

23

2

Ic. SN 74LS08

IC Gate And

24

1

Ic. SN 74LS42

IC Logic Decoder Demux

25

1

Ic. SN 74LS47

IC Logic Decoder BCD

26

1

Ic. SN 74LS147

IC Logic Encoder

27

1

Ic. L 7805

IC Regulator 5 V

28

3

Ic. LM 324

IC Op-Amp

29

1

Ic. LM 35

IC Temperatur Sensor

30

3

Soket IC 16 Pin

Soket IC

31

6

Soket IC 14 Pin

Soket IC

32

1

Soket IC 8 Pin

Soket IC

33

1

Buzzer 5 V

34

1

Fan 12Vdc

Fan 12V 8x8cm

35

1

Soket Molek 2 Pin

Soket Molek

36

1

Header Molek 2 Pin

Header Molek

37

1

Terminal Block 2 Pin

Terminal Block

(5)

5 of 12

No.

Qty.

Value / Tipe Part

Information

39

20 Cm

Wire Black Awg 22

40

100 Cm

Lead 0,8 mm

41

4

Spiser 1 Cm Hexagonal

42

1

PCB 16x10 Cm Plain

PCB 16x10 cm Plain

(6)

6 of 12

OTHERS

Answer Sheet

Competitor Code Competitor Table No. Approval by Jury

ASSIGNED NO. / CODE

(7)

7 of 12

www.inaskills-electronics.com #DESIGN 1

(8)

8 of 12

(9)

9 of 12

(10)

10 of 12

(11)

11 of 12

(12)

12 of 12

Datasheet on desktop

SELAMAT BERLATIH !!!

Akan dilakukan revisi kisi kisi:

LKS 2017 TP16 XXIV HD EN

Hardware Design

Contents

Description of project and tasks

a. Circuit Design and Schematic Capture (Time limit: 2 hrs, 1st day)

b. Design of Printed Circuit Board (Time limit: 2 hrs)

Instructions to the competitor

Parts List

Value / Tipe Part

Transistor NPN

Soket IC 16 Pin

Value / Tipe Part

Answer Sheet

Datasheet on desktop