Viscosity of Fluids
4.4 Electrical Properties
Engineering materials exhibit a great variation in their capacity to conduct electric- ity. This section defi nes the physical properties by which this capacity is measured.
4.4.1 RESISTIVITY AND CONDUCTIVITY
The fl ow of electrical current involves movement of charge carriers—infi nitesimally small particles possessing an electrical charge. In solids, these charge carriers are elec- trons. In a liquid solution, charge carriers are positive and negative ions. The move- ment of charge carriers is driven by the presence of an electric voltage and resisted by the inherent characteristics of the material, such as atomic structure and bonding between atoms and molecules. This is the familiar relationship defi ned by Ohm’s law:
I E __
R (4.6)
where I current, A; E voltage, V; and R electrical resistance, . The resistance in a uniform section of material (e.g., a wire) depends on its length L, cross-sectional area A, and the resistivity of the material r; thus,
R r L __
A or r R A __
L (4.7) where resistivity has units of -m2/m or -m (-in). Resistivity is the basic property that defi nes a material’s capability to resist current fl ow. Table 4.3 lists values of re- sistivity for selected materials. Resistivity is not a constant; instead it varies, as do so many other properties, with temperature. For metals, it increases with temperature.
It is often more convenient to consider a material as conducting electrical current rather than resisting its fl ow. The conductivity of a material is simply the reciprocal of resistivity:
Electrical conductivity 1 __ r (4.8)
where conductivity has units of (-m)1 ((-in)1).
4.4.2 CLASSES OF MATERIALS BY ELECTRICAL PROPERTIES
Metals are the best conductors of electricity, because of their metallic bonding. They have the lowest resistivity (Table 4.3). Most ceramics and polymers, whose electrons are tightly bound by covalent and/or ionic bonding, are poor conductors. Many of these materials are used as insulators because they possess high resistivities.
4.4
Section 4.4/Electrical Properties 91
An insulator is sometimes referred to as a dielectric, because the term dielectric means nonconductor of direct current. It is a material that can be placed between two electrodes without conducting current between them. However, if the voltage is high enough, the current will suddenly pass through the material, for example, in the form of an arc. The dielectric strength of an insulating material, then, is the electrical potential required to break down the insulator per unit thickness. Appropriate units are volts/m (volts/in).
In addition to conductors and insulators (or dielectrics), there are also supercon- ductors and semiconductors. A superconductor is a material that exhibits zero resis- tivity. It is a phenomenon that has been observed in certain materials at low tempera- tures approaching absolute zero. We might expect the existence of this phenomenon, due to the signifi cant effect that temperature has on resistivity. That these supercon- ducting materials exist is of great scientifi c interest. If materials could be developed that exhibit this property at more normal temperatures, there would be signifi cant practical implications in power transmission, electronic switching speeds, and mag- netic fi eld applications.
Semiconductors have already proven their practical worth. Their applications range from mainframe computers to household appliances and automotive engine controllers. As one would guess, a semiconductor is a material whose resistivity lies between insulators and conductors. The typical range is shown in Table 4.3.
The most commonly used semiconductor material today is silicon (Section 7.5.2), largely because of its abundance in nature, relative low cost, and ease of processing.
What makes semiconductors unique is the capacity to signifi cantly alter conductivi- ties in their surface chemistries in microscopic areas to fabricate integrated circuits (Chapter 33).
Electrical properties play an important role in various manufacturing processes.
Some of the nontraditional processes use electrical energy to remove material.
Electric discharge machining (Section 25.3.1) uses the heat generated by electrical energy in the form of sparks to remove material from metals. Most of the important TABLE • 4.3 Resistivity of selected materials.
Resistivity Resistivity
Material ⍀-m ⍀-in Material ⍀-m ⍀-in
Conductors 106108 104107 Conductors, continued
Aluminum 2.8 108 1.1 106 Steel, low C 17.0 108 6.7 106
Aluminum alloys 4.0 108a 1.6 106a Steel, stainless 70.0 108a 27.6 106
Cast iron 65.0 108a 25.6 106a Tin 11.5 108 4.5 106
Copper 1.7 108 0.67 106 Zinc 6.0 108 2.4 106
Gold 2.4 108 0.95 106 Carbon 5000 108b 2000 106b
Iron 9.5 108 3.7 106 Semiconductors 101105 102107
Lead 20.6 108 8.1 106 Silicon 1.0 103 0.4 105
Magnesium 4.5 108 1.8 106 Insulators 10121015 1013–1017 Nickel 6.8 108 2.7 106 Natural rubber 1.0 1012b 0.4 1014b Silver 1.6 108 0.63 106 Polyethylene 100 1012b 40 1014b Compiled from various standard sources.
aValue varies with alloy composition.
bValue is approximate.
welding processes use electrical energy to melt the joint metal. Finally, the capacity to alter electrical properties of semiconductor materials is the basis for microelec- tronics manufacturing.
4.5 Electrochemical Processes
Electrochemistry is a fi eld of science concerned with the relationship between electric- ity and chemical changes, and with the conversion of electrical and chemical energy.
In a water solution, the molecules of an acid, base, or salt are dissociated into positively and negatively charged ions. These ions are the charge carriers in the solution—they allow electric current to be conducted, playing the same role that electrons play in metallic conduction. The ionized solution is called an electrolyte;
and electrolytic conduction requires that current enter and leave the solution at electrodes. The positive electrode is called the anode, and the negative electrode is the cathode. The whole arrangement is called an electrolytic cell. At each electrode, some chemical reaction occurs, such as the deposition or dissolution of material, or the decomposition of gas from the solution. Electrolysis is the name given to these chemical changes occurring in the solution.
Consider a specifi c case of electrolysis: decomposition of water, illustrated in Figure 4.3. To accelerate the process, dilute sulfuric acid (H2SO4) is used as the elec- trolyte, and platinum and carbon (both chemically inert) are used as electrodes. The electrolyte dissociates in the ions H and SO4. The H ions are attracted to the negatively charged cathode; upon reaching it they acquire an electron and combine into molecules of hydrogen gas:
2H 2e → H2 (gas) (4.9a)
The SO4 ions are attracted to the anode, transferring electrons to it to form addi- tional sulfuric acid and liberate oxygen:
2SO4 4e 2H2O → 2H2SO4 O2 (gas) (4.9b) The product H2SO4 is dissociated into ions of H and SO4 again and so the process continues.
4.5
FIGURE 4.3 Example of electrolysis:
decomposition of water.
Review Questions 93
In addition to the production of hydrogen and oxygen gases, as illustrated by the example, electrolysis is also used in several other industrial processes. Two examples are (1) electroplating (Section 27.3.1), an operation that adds a thin coating of one metal (e.g., chromium) to the surface of a second metal (e.g., steel) for decorative or other purposes; and (2) electrochemical machining (Section 25.2), a process in which material is removed from the surface of a metal part. Both these operations rely on electrolysis to either add or remove material from the surface of a metal part. In elec- troplating, the work part is set up in the electrolytic circuit as the cathode, so that the positive ions of the coating metal are attracted to the negatively charged part. In elec- trochemical machining, the work part is the anode, and a tool with the desired shape is the cathode. The action of electrolysis in this setup is to remove metal from the part surface in regions determined by the shape of the tool as it slowly feeds into the work.
The two physical laws that determine the amount of material deposited or removed from a metallic surface were fi rst stated by the British scientist Michael Faraday:
1. The mass of a substance liberated in an electrolytic cell is proportional to the quantity of electricity passing through the cell.
2. When the same quantity of electricity is passed through different electrolytic cells, the masses of the substances liberated are proportional to their chemical equivalents.
References
[1] Guy, A. G., and Hren, J. J. Elements of Physical Metallurgy, 3rd ed. Addison-Wesley, Reading, Massachusetts, 1974.
[2] Flinn, R. A., and Trojan, P. K. Engineering Materials and Their Applications, 5th ed. John Wiley & Sons, New York, 1995.
[3] Kreith, F., and Bohn, M. S. Principles of Heat Transfer, 6th ed. CL-Engineering, New York, 2000.
[4] Metals Handbook, 10th ed., Vol. 1, Properties and Selection: Iron, Steel, and High Performance
Alloys. ASM International, Metals Park, Ohio, 1990.
[5] Metals Handbook, 10th ed., Vol. 2, Properties and Selection: Nonferrous Alloys and Special Purpose Materials. ASM International, Metals Park, Ohio, 1990.
[6] Van Vlack, L. H. Elements of Materials Science and Engineering, 6th ed. Addison-Wesley, Reading, Massachusetts, 1989.
Review Questions
4.1 Defi ne density as a material property.
4.2 What is the difference in melting characteris- tics between a pure metal element and an alloy metal?
4.3 Describe the melting characteristics of a non- crystalline material such as glass.
4.4 Defi ne specifi c heat as a material property.
4.5 What is thermal conductivity as a material property?
4.6 Defi ne thermal diffusivity.
4.7 What are the important variables that affect mass diffusion?
4.8 Defi ne resistivity as a material property.
4.9 Why are metals better conductors of electricity than ceramics and polymers?
4.10 What is dielectric strength as a material property?
4.11 What is an electrolyte?
Problems
Answers to Problems labeled (A) are listed in the Appendix at the back of the book.
4.1(A) (USCS units) Determine the increase in length of a steel bar whose length 100 in, if the bar is heated from room temperature of 70F to 500F. Use Table 4.1 for reference.
4.2 (SI units) Determine the length and width of a rectangular nickel plate whose room tempera- ture (20C) dimensions are 750 mm by 400 mm by 5 mm, if the plate is heated to 250C. Use Table 4.1 for reference.
4.3(A) (SI units) A steel shaft has a starting diam- eter 15.00 mm. It is to be inserted into a hole in an expansion fi t assembly operation. To be readily inserted, the shaft must be reduced in diameter by cooling. Determine the tempera- ture to which the shaft must be reduced from room temperature (20C) in order to reduce its diameter to 14.98 mm. Use Table 4.1 for reference.
4.4 (SI units) A bridge to be fabricated of steel girders is designed to be 500 m long and 12 m wide at ambient temperature (assumed 20C).
Expansion joints will be provided to compen- sate for the change in length in the girders as the temperature varies. Each expansion joint can compensate for a maximum of 20 mm of change in length. From historical records it is estimated that the minimum and maximum temperatures in the region will be 35C and 40C, respectively. Determine (a) the minimum number of expansion joints required and (b) the length that each bridge section should be fabricated. Use Table 4.1 for reference.
4.5 (USCS units) A zinc die casting has a critical dimension of 7.500 in when it solidifi es in the mold at its melting temperature because 7.500
in is the corresponding mold dimension. What is the value of this part dimension when it cools to room temperature (70F)? Use Table 4.1 for reference.
4.6 (SI units) Aluminum has a density of 2.70 g/cm3 at room temperature (20C). Determine its den- sity at 650C, using data in Table 4.1 for reference.
4.7 (SI units) Determine the amount of heat required to increase the temperature of an alu- minum block that is 10 cm by 10 cm by 10 cm from room temperature (21C) to 300C. Use Table 4.2 for reference.
4.8 (SI units) What is the resistance R of a length of copper wire whose length 10 m and whose diameter 0.30 mm? Use Table 4.3 for reference.
4.9(A) (USCS units) A 16 gage copper wire (0.0508- in diameter) connects a solenoid to a control cir- cuit that is 50 ft away. (a) What is the resistance of the wire? Use Table 4.3 as a reference. (b) If a current was passed through the wire, it would heat up. How does this affect the resistance?
4.10 Aluminum wiring was used in many homes in the 1960s due to the high cost of copper at the time. Aluminum wire that was 12 gauge (a measure of cross-sectional area) was rated at 15 A of current. If copper wire of the same gauge were used to replace the aluminum wire, what current should the wire be capable of car- rying if all factors except resistivity are consid- ered equal? Assume that the resistance of the wire is the primary factor that determines the current it can carry and the cross-sectional area and length are the same for the aluminum and copper wires.
5 Dimensions, Surfaces,
and their
Measurement
Chapter Contents
5.1 Dimensions, Tolerances, and