• Apply high pressure oil until oil seeps shaft, below the coupling flange
• Rotate the camshaft by means of a tool till the mark matches both the sides of the pin gauge
As described above, due to two different types of pumps, we use two different methods to check the delivery stroke of the fuel pump i.e effective stroke of the fuel pump.
Suction spill control valve type fuel pump Timing Check:
Before opening the fuel pump for
checking the timing, ensure to change over the engine from heavy oil to diesel oil and take prior permission from the company and port authority for
immmobilisation. Procedure for checking fuel pump timing:
• Keep the main and crosshead lube oil pumps running
• Put local reversing lever in ahead direction
• Shut starting air valve to main engine and inlet air valve to distributor
• Open indicator cocks and engage the turning gear
• Now put the local fuel lever to the max fuel notch position. This will vent the cylinder in the governor and also activate the shut down servomotor i.e. rack is free to move from ‘0’ to
‘maximum’ position( Once the engine is stopped, the shut-down servomotor gets de-activated i.e. air vented and it keeps the fuel rack locked in the zero postion).
• Measure the VIT rack distance and note it down. Set it to zero and lock it with spacer and nut
• Fuel quality lever to be set at ‘0’
• Keep three dial gauges near the engine
• Shut the fuel inlet to the pump and drain the oil from the pump casing by opening the bottom drain valve
• Remove the protection cover from the suction, spill and discharge valve
• Remove pressure bush with special tools ( the pressure bush holds the valve seat in place)
• Remove the springs and valves
• Clean the valves and springs with kerosene
• Mount back the spill and suction valves and pressure bush without springs
A Guide to Two Stroke Marine Engine Components
• Turn the engine in ahead direction till the cam is on its peak. This ensures that the suction valve is closed
• Keep the dial gauge over top of the suction valve with 1mm pre-tension and set it to ‘0’
• Now turn the engine in astern
Suction
Discharge
Spill
95
Sulzer Fuel Pump
www.marineinsight.com
direction till the cam is on the base circle, which indicates spill valve is closed
• Put dial gauge over top of the spill valve with 1mm pre-tension and set it to ‘0’
• Keep the third dial gauge over the plunger of discharge side with 1mm pretension and set it to ‘0’
• Now turn the engine in ahead direction till the dial gauge on suction valve
shows 0.02 mm deflection. Check and note the reading of plunger dial gauge and mark it as ‘a’
• Keep turning the engine till the dial gauge on the spill valve shows
0.02mm deflection. Note the reading
• of plunger dial gauge and mark it as
‘b’
Effective stroke of the fuel pump=
‘b’ – ‘a’
Jerk type/ Helix Port Controlled Pump:
In jerk type helix port controlled fuel pump, the timing is measured by taking the fuel pump lead.
The fuel pump lead is the distance from the top of fuel pump plunger when lifted above the upper edge of the upper cut- off holes of the fuel pump barrel,when the same unit’s piston is at TDC.
Following procedure is to be used for finding out fuel pump lead:
• Close the oil inlet to the fuel oil pump
and drain the pump
• Disconnect the fuel oil index rod from the fuel rack
• Open the erosion plugs from the fuel pump housing
• Diconnect the high-pressure pipes and air pipe for the puncture valve
• Remove the puncture valve from the top cover
• Use the extractor tool to remove the suction valve from the top cover
• Use compressed air to clean the lower cut-off holes and the cross bore
• If the engine is of the reversible type
A Guide to Two Stroke Marine Engine Components
ensure that the roller guide is in AHEAD position
97
MAN Fuel Pump
www.marineinsight.com
• Turn AHEAD until the cross bore in the plunger is aligned with the lower cut- off holes
• Ensure that the plunger is in delivery stroke to obtain the correct alignment of plunger and cut off holes
• Push the measuring pin right down against the bottom of the hole in the
plunger
• Verify that the cross bore and the
lower cut-off holes are in alignment by flashing a torch through the cut-off
holes
• Turn AHEAD until the lower edge of the cross bore in the plunger reaches the exact position at which it closes off the upper edge of the lower cut-off holes
• If the exact position is difficult to determine due to fuel oil deposits in the plunger/barrel assembly, use compressed air to clean the lower cut-off holes
• Now mount the measuring tool on top of the fuel pump cover
• Adjust the bracket of the measuring tool until the plunger of the dial gauge is almost at its bottom position. Adjust the scale to 0 (zero)
• Turn AHEAD until the piston of the cylinder concerned is at TDC
• When the exact position of the piston has been confirmed to be at TDC, either by checking the position of the crankthrow or the marks on the
turning wheel, note down the reading
on the dial gauge and calculate the deviation “x” between the “0” position and the present position
The fuel pump lead “a” is then calculated as follows: “a = x + Y (correction factor)”
The adjustment factor “Y” is a correction factor. It is basically the distance
between the plunger top and upper cut- off holes top, when the plunger top
reaches the exact position at which the light cannot be seen through the lower cut off holes in the barrel and plunger.
A Guide to Two Stroke Marine Engine Components
99