■ Programming a memory channel
VFO mode settings, including the set mode contents such as subaudible tone frequency, etc., can be programmed into a memory channel.
➀Set the desired frequency in VFO mode:
➥Push [V/MHz] to select VFO mode.
➥Set the frequency using the tuning dial.
➥Set other data (e.g. tone frequency, etc.) if required.
➁Push [S.MW] momentarily.
• “!” and the memory channel number flash.
➂Rotate the tuning dial to select the memory channel to be
programmed.
• Memory channels not yet programmed are blank.
➃Push [S.MW] for 1 sec. to program.
• 3 beeps may sound.
• Memory channel number automatically advances when continu- ing to push [S.MW] after programming.
✔CONVENIENT
Memory programming can be performed in versatile ways e.g. memory channel to the same (or different) memory chan- nel, memory channel to the call channel, etc.
[EXAMPLE]: Programming 145.870 MHz into memory channel 20 via the front panel.
5 9 1
M 1 5
Push [V/MHz]
Rotate for setting
freq., etc.
Rotate
Push
momentarily
Push
for 1 sec. and continue pushing
X
9 1 5
S.MWMW
S.MWMW
9 1 5
M X
5 9 1
M 9 1 5
M X
9 1 5
Downloaded from www.Manualslib.commanuals search engine
28
6 MEMORY OPERATION
[EXAMPLE]: Programming 145.870 MHz into memory channel 20 via the microphone.
■ Programming a memory channel via the microphone
The microphone can also be used to program memory channels.
ÄSet the desired frequency in VFO mode:
➥Push [VFO] to select VFO mode.
➥Set the frequency using the keypad.
➥Set other data (e.g. offset frequency, duplex direction, subaudible tone encoder ON/OFF and its frequency), if necessary.
ÅPush [FUNC], then [EMW] momentarily.
ÇSelect the memory channel to be programmed.
➥Push [Y] or [Z] to select the memory channel (direct nu- meral input cannot be used).
ÉPush [FUNC] then [EMW] for 1 sec. to program.
➥3 beeps may sound and the VFO contents (including the subaudible tone frequency, etc.) are programmed.
➥Memory channel number advances when continuing to push [MW] after programming.
MW
Push Push then
momentarily
Push
Push for 1 sec. and
continue pushing
VFO
8
DUP+ DUP7 5
MID
0 1
MONI HIGH4 C
ENT
MW FUNC CLRA
then
MW FUNC CLRA
5 9
1 15 9 5 9
1 M 1 5
M X
9 15
M 5 9 1
M 5 9 1
29
6
MEMORY OPERATION
■ Transferring memory contents
This function transfers a memory channel’s contents to VFO (or another memory/call channel). This is useful when search- ing for signals around a memory channel frequency and for recalling the offset frequency, subaudible tone frequency, etc.
➀Select the memory channel to be programmed.
➥Select memory mode by pushing [M/CALL] once or twice (“!” appears).
➥Rotate the tuning dial to select the memory channel.
➁Push [S.MW] momentarily, then rotate the tuning dial to se- lect another memory channel to transfer.
• To transfer to the VFO, push and hold [(S.MW)MW] instead of pushing momentarily.
➂Push and hold [(S.MW)MW] to transfer when a momentary push was used in the previous step.
Push
+
for 1 sec.
MW FUNC CLRA
S.MWMW
DUP T
M 5 9 1
DUP T
5 9 1
ÄSet the memory channel to be transferred:
➥Push [MR] to select memory mode.
➥Push [Y] or [Z] to select the memory chan- nel; or push [GENT] then push the desired memory channel number (3 digits) to select the memory channel directly.
ÅPush [FUNC] then [EMW] momentarily, then push [Y] or [Z] to select another memory chan- nel to transfer.
• To transfer to the VFO, push [FUNC] then push and hold [EMW] instead of pushing momentarily.
ÇPush [FUNC] then [EMW] for 1 sec. to transfer.
MW
Downloaded from www.Manualslib.commanuals search engine
30
6 MEMORY OPERATION
☞NOTE: Be careful—the contents of cleared memories CANNOT be recalled.
■ Memory clearing
Contents of programmed memories can be cleared (blanked), if desired.
➀Push [S.MW] momentarily.
➁Select the memory channel to be cleared with the tuning dial.
➂Push [S.MW] briefly, then a second time for 1 sec.
• 3 beeps sound, then the frequency is cleared.
• “!” flashes continuously.
• Scan edges 1A/1b and the call channel cannot be cleared.
➃Push any switch to stop the flashing.
[EXAMPLE]: Clearing memory channel 20.
M X
9 15
Push Rotate
momentarily
again for 1 sec.
Push S.MWMW briefly, then push S.MWMW Push any switch
S.MWMW
X
9 1 5
M 9 1 5
M 5 9
1 5 9
1
31
6
MEMORY OPERATION
■ Alphanumeric display
Each memory channel and the call channel can be pro- grammed with an alphanumeric name such as a repeater name, club name, etc., for easy recognition. Names can be a maximum of 6 characters—see the table below for avail- able characters.
☞NOTE: Scan edge channels and scratch pad memories CANNOT be programmed with alphanumeric names.
➀Push [M/CALL] to select memory mode (or call mode) if necessary.
➁Rotate the tuning dial to select the desired memory chan- nel.
1 2 3 4 5 6 7 8 9 10
A B C D D E F G H I
J K L M N O P Q R S
T U V W X Y Z + – M
/ = _ < > ( ) , : space
➂Push [(MONI)ANM] for 2 sec. to select alphanumeric indi- cation.
• “NONAME” appears when a name has not yet been programmed into the channel.
➃Push [SET] to enter programming mode.
• The first character of the name flashes.
➄Rotate the tuning dial to select the desired character.
• See the table at left for a list of available characters.
➅Push [SET] to advance to the next character.
• Push [MONI] to select the previous character.
➆Push [V/MHz] to program the name and exit programming mode.
➇Push [(SET)ANM] for 2 sec. to return to frequency indica- tion if desired.
[EXAMPLE]: Programming “CLUB” into memory channel 1.
Push for 1 sec.
[ANM]
Push Repeat previous step until the
desired name is displayed rotate
[SET]
then push [MONI]
Push to program
[V/MHz]
5 9 9 1
15 9
1 5
M M M
Downloaded from www.Manualslib.commanuals search engine
32