• Tidak ada hasil yang ditemukan

INSTITUTE OF AERONAUTICAL ENGINEERING - IARE

N/A
N/A
Protected

Academic year: 2024

Membagikan "INSTITUTE OF AERONAUTICAL ENGINEERING - IARE"

Copied!
2
0
0

Teks penuh

(1)

Hall Ticket No Question Paper Code: AEE007

INSTITUTE OF AERONAUTICAL ENGINEERING

(Autonomous)

B.Tech IV Semester End Examinations (Supplementary) - June, 2018 Regulation: IARE – R16

AC MACHINES

Time: 3 Hours (EEE) Max Marks: 70

Answer ONE Question from each Unit All Questions Carry Equal Marks

All parts of the question must be answered in one place only

UNIT – I

1. (a) Explain the constructional details and working principle of three phase induction motor with

neat sketch. [7M]

(b) A three phase, 50Hz, 8 pole, induction motor has full load slip of 2%. The rotor resistance and stand still rotor reactance per phase are 0.001ohm and 0.005 ohm respectively. Find the ratio of the maximum to the full load torque and speed at which the maximum torque occurs. [7M]

2. (a) Draw and explain the torque-slip characteristics of the three phase induction motor with different

modes of operation. [7M]

(b) A three phase star connected 400V, 50Hz four pole induction motor has the following per phase parameters in ohms, refer to the stator. R1=0.15, X1=0.45 R21=0.12, X21=0.45 Xm=28.5 compute the stator current and power factor when the motor is operated at rated voltage and

frequency with s=0.04. [7M]

UNIT – II

3. (a) What are the different staring methods for induction motor and explain the auto transformer

starting method for three phase induction motor? [7M]

(b) A six pole, 50Hz three phase induction motor running at 960rpm on full load 4% slip develops a torque of 149.3N-m at its pulley rim. The friction and windage losses are 200W and stator

copper and iron loses equal 1,620W. Calculate the [7M]

i. Output power

ii. The rotor Copper losses iii. The efficiency at full load.

4. (a) With the neat circuit diagram explain indirect method to determine the efficiency of three phase

induction motor. [7M]

(b) With the aid of torque-speed characteristic explain the operation of induction generator. [7M]

Page 1 of 2

(2)

UNIT – III

5. (a) Describe the difference in construction of rotors of alternators used in hydroelectric plants and

steam plants. Draw neat sketch of two types of rotors. [7M]

(b) A three phase, 6 pole synchronous generator has a resultant air gap flux of 0.06wb per pole. The flux is distributed sinusoidally over the pole. The stator has 2 slots per pole per phase and 4 conductors per slot are accommodated. The coil span is1500 electrical. Calculate the phase and

line induced voltages when the machine runs at 375 rpm. [7M]

6. (a) What do you mean by synchronizing of alternator? Describe any one method of synchronizing.

(b) With the aid of circuit diagram for inductive impedance between two voltages sources and is associated phasor diagram and derive the expression for power developed. [7M]

UNIT – IV

7. (a) Explain different methods of starting synchronous motor. [7M]

(b) A 2000V, three phase, star connected synchronous motor an effective resistance and synchronous reactance of 0.2 ohms and 2.2 ohms per phase respectively. The input is 800KW at nominal voltage and the induced line emf is 2500V. Calculate the line current and PF. [7M]

8. (a) Explain the effect of excitation on armature control and power factor for synchronous motor.

[7M]

(b) A 6600V, star connected three phase synchronous motor works at constant voltage and constant excitation. Its synchronous reactance is 20 ohm per phase and armature resistance is negligible.

When the input power is 1000KW, the power factor is 0.8 leading. Find the power angle and

power factor when the input is increased to 1500kW. [7M]

UNIT – V

9. (a) Explain the principle of operation of the single phase induction motor by the double field revolving

theory. [7M]

(b) Explain the operation of capacitor start-run induction motor. [7M]

10. (a) Draw and explain the equivalent circuit of a single phase induction motor without core losses?

[7M]

(b) Find the mechanical power output of 185W, 4 pole, 110V, 50Hz single phase induction motor, whose constants are given below at a slip of 0.05. R1=1.86 ohm, X1=2.56 ohm R2=3.56 ohm, X21=0.45X2=2.56 ohm,Xm=53.5 ohm, friction and windage losses are 13.5W. [7M]

− ◦ ◦ ◦ ◦ −

Page 2 of 2

Referensi

Dokumen terkait

[7M] UNIT-V 9.a Explain different components of aircraft wing with help of diagram and explainabout the types load bared by each component.. [7M] .b What do you understand by the

[7M] b Determine purpose of distributed database access primitives in distributed databases and show how integrity constraints are used in distributed databases [7M] UNIT-IV 7.. a

[7M] b A 15 KVA, 2300/230V, 50Hz single phase transformer gave the following test data open circuit testVo=2300V,Io=0.21A,Wo=50W H.V side short circuit testVsc=47V,Isc=6.0A,Wsc=160w

[7M] b Prepare a purchases return journal book from the following transactions for January 2014:[7M] Table 3 Date Details Amount Rs.. a Bike Ltd purchased 10 bikes during January and

[7M] b A random process is defined as Xt=A coswct+ θ where θ is a uniform random variable over0,2π .Verify the process is ergodic in the mean sense and auto correlation sense [7M] 8..

a Discuss the action of a synchronous phase modifiers for voltage regulation of a line and explain carefully how its use increases the current carrying capacity of a transmission line..

a Explain the operation of single phase fully controlled converter fed separately excited DC motor in continuous current mode.. Sketch the waveforms of output voltage and

When the current is 40 mA and its resistance is 25Ω, calculate the value of the shunt to be connected in parallel with the meter to enable it to be used as an ammeter for measuring