Simulation And Analysis Of Defected Ground Structure (DGS) As A Quarter Wavelength At 2.4 GHZ Band.

(1)

i

Simulation and Analysis of Defected Ground Structure (DGS) as a Quarter

Wavelength at 2.4 GHz band

LIM YAN CHINN

This report is submitted in partial fulfillment of the requirements for award of Bachelor

of Electronic Engineering (Telecommunication Electronics) With Honours

Faculty of Electronic and Computer Engineering

Universiti Teknikal Malaysia Melaka

(2)

ii

UNIVERSTI TEKNIKAL MALAYSIA MELAKA

FAKULTI KEJURUTERAAN ELEKTRONIK DAN KEJURUTERAAN KOMPUTER

BORANG PENGESAHAN STATUS LAPORAN PROJEK SARJANA MUDA II

Tajuk Projek : Simulation and Analysis of DGS as quarter wavelength at 2.4GHZ _………

Sesi

Pengajian :

1 0 / 1 1

Saya ………LIM YAN CHINN………

(HURUF BESAR)

mengaku membenarkan Laporan Projek Sarjana Muda ini disimpan di Perpustakaan dengan syarat-syarat kegunaan seperti berikut:

1. Laporan adalah hakmilik Universiti Teknikal Malaysia Melaka.

2. Perpustakaan dibenarkan membuat salinan untuk tujuan pengajian sahaja.

3. Perpustakaan dibenarkan membuat salinan laporan ini sebagai bahan pertukaran antara institusi

pengajian tinggi.

4. Sila tandakan ( √ ) :

SULIT*

*(Mengandungi maklumat yang berdarjah keselamatan atau kepentingan Malaysia seperti yang termaktub di dalam AKTA RAHSIA RASMI 1972)

TERHAD** **(Mengandungi maklumat terhad yang telah ditentukan oleh organisasi/badan di mana penyelidikan dijalankan)

TIDAK TERHAD

Disahkan oleh:

__________________________ ___________________________________

(TANDATANGAN PENULIS) (COP DAN TANDATANGAN PENYELIA)

(3)

iii

“I hereby declare that this report is the result of my own work except for quotes as cited in the references.”

Signature :

Author : LIM YAN CHINN

(4)

iv

I hereby declare that I have read this report and in my opinion this report is sufficient in

terms of the scope and quality for the award of bachelor of Electronic Engineering

(Industrial Electronics) With Honours.”

Signature :

Supervisor’s Name : En. NOOR AZWAN SHAIRI

(5)

v

Dedicated to my beloved family especially my father and mother, lecturer, and also to

(6)

vi

ACKNOWLEDGEMENT

First and foremost, I would like to praise God for His blessing. He gave me

physical and mental strength to carry on my final year project up to completion.

I would like to express gratitude and thanks to my supervisor, Mr. Noor Azwan

Shairi for his support and unfailing patience throughout the duration of the project. His

encouragement and guidance are truly appreciated. Otherwise, this project has not been

possible. I have learnt a lot under her guidance, be it practically or theoretically.

Other than that, I am also grateful to my all friends who help me and giving me

opinion along implementation of this project.

I would like to thanks my parents on their moral support as I can count on them

whenever I am upset or down.

Finally, I would like to offer thanks and deepest gratitude from the bottom of my

heart for all the support, encouragement and inspirations I obtained throughout the

duration of this project. The help rendered to me priceless, be it from the smallest of its

(7)

vii

ABSTRACT

DGS which is known as defected ground structure has been an increasing interest

in studying microstrip lines with various etched defect on ground plane that prohibit

wave propagation in certain frequency bands. The proposed DGS unit structure can

provide the band gap characteristic in some frequency bands with only one or more unit

lattice. By using a simple circuit analysis method, the equivalent circuit parameters are

extracted. By employing the extracted parameters and circuit analysis method, the band

gap effect for the provided defected ground structure can be explained. The low pass

filters can be designed and implemented by using the derived and extracted equivalent

circuit and parameter. Lastly, the overall results are an efficient and accurate means to

produce the complete equivalent models of DGS circuit for the design of various RF,

(8)

viii

ABSTRAK

DGS dikenali sebagai berpaling tadah struktur bawah telah menjadi satu faedah

yang meningkatkan minat dalam belajar baris-baris mikrojalur dengan menjelma

pelbagai jenis kecacatan bergores pada satah bumi yang melarang perambatan

gelombang dalam kumpulan-kumpulan frekuensi tertentu. Struktur unit DGS yang telah

dicadangkan boleh menyediakan jurang jalur biasa dalam beberapa jalur-jalur frekuensi

dengan hanya satu atau lebih kekisi unit. Kaedah analisis litar mudah telah digunakan

bagi mengenal pasti parameter litar adalah setara dan berpaling tadah struktur bawah

dapat dijelaskan. Penapis lulus rendah boleh direka serta dilaksanakan dengan

menggunakan terbitan dan mengambil litar setara serta parameter. Akhir sekali,

keputusan secara keseluruhan adalah cekap dan tepat bagi menjanakan model-model

setara lengkap litar DGS dengan memperkenalikan pelbagai jenis bentuk radio

frequenksi , dan gelombang mikro litar yang memerlukan prosedur-prosedur reka bentuk

(9)

ix

II LITERATURE REVIEW

2.1 Introduction 4

2.2 DGS Unit Cell 6

2.3 Equivalent circuit of DGS 7

2.4 DGS as a Quarter Wavelength 9

2.5 DGS Characteristic 10

2.6 Smith Chart 11

2.7 Scattering Parameter 14

2.8 Application of DGS 16

III METHODOLOGY

3.1 Methodology 17

3.2 Flow Chart Diagram 18

3.3 DGS Simulation 20

3.4 Schematic Design 21

3.5 Layout Design 26

3.6 Transmission Line Design 27

3.7 Defected Ground Structure (DGS) Layout Design 27

IV RESULT AND ANALYSIS

4.1 Introduction 31

4.2 Analysis of LC Circuit (Circuit Simulation) 31

4.3 Quarter wavelength Circuit 36

4.4 Parallel RLC equivalent circuit 38

4.5 Parallel LC in series with R equivalent circuit 39

4.6 DGS Layout Design (EM Simulation) 41

(11)

xi

4.6.2 Influence of the Gap Distance 44

4.6.3 Influence of the Slot Wide 47

4.6.4 Influence of the Length of Slot 50

4.7 General Circuit Model for DGS 53

4.7.1 Influence of Electrical Length, E 53

4.7.2 Influence of Impedance, Z 55

V CONCLUSION AND RECOMMENDATION

5.1 Conclusion 57

5.2 Recommendation 58

(12)

xii

LIST OF TABLES

NO TITLE PAGE

4.1 Result of influence square lattice dimension 43

4.2 Result of influence gap distance 46

4.3 Result of influence slot wide 49

4.4 Result for the Influence of length of slot 52

4.5 Result with different value of electrical length, E 54

(13)

xiii

LIST OF FIGURES

NO TITLE PAGE

2.1 Different types of DGS 5

2.2 Dumbbell shapes of DGS 6

2.3 LC equivalent circuits of Dumbbell DGS 7

2.4 RLC equivalent circuits of Dumbbell DGS 8

2.5 π Shaped equivalent circuits 9

2.6 The fast wave and slow wave that comprise the model waveform 11

2.7 An impedance Smith chart 12

2.8 S Parameter Two Port Model 14

3.1 Flow Chart Diagram 18

3.2 ADS software 20

3.3 Creating Project 22

3.4 Creating Design (Schematic) 22

3.5 Equivalent circuit used in Schematic (ADS) 23

3.6 Example of Smith Chart used in ADS 23

3.7 Band stop filter frequency response 24

3.8 DGS layout as example 24

3.9 Values for Inductor and Capacitor can be tuned after the setting 25

has been done

3.10 Tune parameter which used to vary values of components 25

3.11 Design and analysis method of dumbbell DGS 26

3.12 Substrate setup and Layers mapping 28

(14)

xiv

3.14 S-parameter momentum simulation 29

3.15 Momentum simulation setup 29

3.16 (a) Component library (b) Choose the layout component from the library 30

3.17 Schematic layout looks like of DGS 30

4.1 LC equivalent circuit 31

4.2 Simulation result 32

4.3 Simulation result in Smith Chart of S(1,1) 33

4.4 S(1,1) Phase response 33

4.5 Results of S(1,1) showing different values of frequency when value 34

of Inductor is varied

4.6 Results of S(1,1) showing different of phase response when value 34

of Inductor is varied

4.7 Results of S(1,1) showing different values of frequency when value 35

of Capacitor is varied

4.8 Results of S(1,1) showing different of phase response when value 35

of Capacitor is varied

4.9 Quarter wavelength Circuit 36

4.10 Simulated S(1,1) of Phase Response 37

4.11 Smith Chart shows Short to Open 37

4.12 Parallel RLC equivalent circuit 38

4.13 Simulated S(1,1) of Phase responses 38

4.14 Simulated S(1,1) 39

4.15 Parallel LC Series with R equivalent circuit 39

4.16 Simulated S(1,1) 40

4.17 Simulated S(1,1) of phase response 40

4.18 EM Simulation for DGS unit cell 41

4.19 Simulated S(1,1) for the proposed DGS 42

4.20 Simulated S(1,1) which the markers marked at open circuit 42

4.21 Simulated S(1,1) which the markers marked at 2.4 GHz 43

4.22 EM Simulation for DGS unit cell 44

(15)

xv

4.24 Simulated S(1,1) which the markers marked at open circuit 45

4.25 Simulated S(1,1) which the markers marked at 2.4 GHz 45

4.26 EM Simulation for DGS unit cell (Bottom view) 47

4.28 Simulation result of S(1,1) in Smith Chart which the markers 48

marked at open circuit

marked at 2.4 GHz

4.30 EM Simulation for DGS unit cell (Bottom view) 50

marked at open \circuit

marked at 2.4 GHz

4.34 Circuit Model for DGS 53

4.36 Simulation result of S(1,1) in Smith Chart at 2.4 GHz 54

4.37 Circuit Model for DGS 55

(16)

xvi

LIST OF ABBREVIATION

DGS Defected Ground Structure

PBG Photonic band-gap

ADS Advanced Design System

EM Electromagnectic

RF Radio Frequency

AC Alternating Current

MW Microwave

3D Three Dimensions

(17)

1

CHAPTER I

INTRODUCTION

1.1 Background

In past few years, Defected Ground Structure (DGS) has played an

important role in radio frequency/microwave circuits. The first defected ground

structure was proposed in 1999 which based on the idea of photonic band-gap

(PBG) structure and its application can be found in the design of planar circuits

and low pass filter [1]. However, it is difficult to use a PBG structure for the

design of microwave components due to the difficulties of the modeling. Another

difficulty in using the PBG circuit is caused by the radiation from the periodic

etched effects [5]. A DGS is where the ground plane metal is purposely modified

with certain geometry to enhance performance. A variety of slot geometry is

realized by etching a defective pattern in the ground plane which disturbs the

shield current distribution in the ground plane. It can also be used in various

circuits with antenna, filters, delay lines, phase shifters and so on [1].

The disturbance can change the characteristic of a transmission line, such

as equivalent capacitance or inductance to obtain the slow wave effect and the

band stop property [6]. In a word, any defect ground structure etched in the

(18)

2

and inductance. In order to maintain the biasing line of DGS as a quarter

wavelength, physical width has to be wider and length is shorter than that of the

conventional bias line.

This project will further investigate the capability of DGS as a quarter

wavelength at 2.4 GHz band. It involves software called Advanced Design

System (ADS) to design and simulate the DGS.

1.2 Project Objective

The objective of this project is to do the parametric studies on the DGS as a

quarter wavelength by analyzing at the DGS equivalent circuit and layout.

1.3 Problem Statement

1. No detail parametric study on the phase response of DGS at quarter

wavelength [1,6,10,11].

2. Most of the technical papers focus on applications of DGS [5,7,9,17].

1.4 Scopes of Project

1. Design the DGS as quarter wavelength in ADS software as an equivalent

circuit and layout.

2. Simulate and analyze the DGS in equivalent circuit and EM simulation in

(19)

3

1.5 Methodology

This project consists of three stages. The literature review and

background study are done for the first stage such as the basic conceptions and

transmission characteristics of DGS. The equivalent circuit models of varieties of

DGS units are also presented. After finished the study, second stage will be

precede on the equivalent circuit and EM simulation by using Advanced Design

System (ADS). Next, simulation results are compared by analysis the phase

(20)

4

CHAPTER II

LITERATURE REVIEW

2.1 Introduction

Recently, there has been an increasing interest in studying microstrip

lines that prohibit wave propagation in certain frequency bands using defected

ground structure (DGS) [1,2,3,4,5,6]. Therefore, DGS is an etched periodic or

non-periodic cascaded configuration defect in ground of a planar transmission

line such as microstrip, coplanar and conductor backed coplanar waveguide

which disturbs the shield current distribution in the ground plane cause of the

defect in the ground. This disturbance will change characteristic of a

transmission line just like line capacitance and inductance [1].

. DGS can be realized by etching off a simple shape in the ground plane,

depending on the shape and dimensions of the defect, the shielded current

distribution in the ground plane is disturbed, resulting a controlled excitation and

propagation of the electromagnetic waves through the substrate layer. The shape

of the defect may be changed from the simple shape to the complicated shape for

the better performance [5].

(21)

5

Different shapes of DGS have been studied such as concentric ring circle,

spiral, dumbbells, elliptical and U- and V- slots. Every DGS shapes can be

represented as a circuit consisting of inductance and capacitance, which can

leads to a certain frequency band gap determined by the shape, dimension and

position of the defect. DGS gives an extra degree of freedom in microwave

circuit design and can be used for various types of applications [2].

Figure 2.1: Different types of DGS: (a) spiral head (b) arrow-head slot (c) “H”

shape slot (d) square open-loop with a slot in middle section (e) open loop

dumbbell (f) inter-digital DGS [1]

In RF circuit, DGS provides a significant advantage by extending its

applicability such in amplifiers, low pass filter, power dividers, couplers and RF

switch. Researchers of DGSs are interested in the area of extensive capability in

microwave circuit. The parameters of equivalent circuit model of DGSs were

also researched and utilized to design. Many passive and active microwave and

millimeter devices have been developed to suppress harmonics and realize the

compact physical dimensions of circuits for the design flow of circuits with DGS

(22)

6

2.2 DGS Unit Cell

Figure 2.2 Dumbbell shapes of DGS [1].

A unit DGS (dumbbell) section is created in the ground plane as show in

Figure 2.2 [5]. In many microwave circuits, the dumbbell shaped DGS pattern is

commonly adopted because easy and simple to design. The dumbbell DGS are

composed of two a x b rectangular defected areas, g x w gaps and narrow

connecting slot wide etched area in backside metallic ground plane as shown in

Figure 2.2 [1].

The DGS with the microstrip line employs and intentional defect on the

ground and it provides band stop characteristic from the resonance property. The

cut off frequency of the DGS is mainly dependent on the etched square area in

ground plane. There is an attenuation pole location, which is due to the etched

gap distance [1, 5].

An attenuation pole can be generated by combination of the inductance

and capacitance elements. The frequency characteristic of the DGS section can

be explained by varied the value of capacitor. The etched gap area, which is

placed under a conductor line, provides the parallel capacitance with effective

(23)

7

The proposed DGS section is fully describe by two parameters, they are

the etched lattice dimension and the gap distance. Thus, different types of shape

and slot geometries will affect the resonant frequency. Both of these will control

the fundamental resonant frequency and higher order resonances [6]. To fulfill

the different requirements, a variety of DGS shapes have evolved over time.

2.3 Equivalent circuit of DGS

Usually, design and analysis are two challenges for DGS. It is needed to

remove the equivalent circuit parameters by applying the proposed DGS section

to a practical circuit design example. In order to derive the equivalent circuit

parameters of DGS unit at the reference plane, the S-parameter versus frequency

should be calculated by full wave electromagnetic (EM) simulation to explain the

cutoff and attenuation pole characteristic of the DGS section. At present, DGS

can be equivalent by three types of equivalent circuits: (1) LC and RLC

equivalent circuits, (2) π shaped equivalent circuit, (3) quasi-static equivalent

circuit. For this project, the DGS will only use the LC and RLC equivalent

circuit as shown in Figure 2.3 and Figure 2.4 [1].

(24)

8

The LC equivalent circuit of DGS with rectangular parts of dumbbell

DGS increase route length of current and the effective inductance. The effective

capacitor of the microstrip line can be increased by inserting a slot in the ground

surface to accumulate the charge. Two rectangular defected areas and one

connecting slot correspond to the equivalently added inductance (L) and

capacitance (C) respectively. A resonance will only occur at a certain frequency

because of the parallel LC circuit. As the etched area of the unit lattice increases,

the effective series inductance increase and increasing the series inductance gives

rise to a lower cut off frequency. When the etched gap distance increases, the

effective capacitance decreases so that the attenuation pole location moves up to

higher frequency [1].

Figure 2.4: RLC equivalent circuits of Dumbbell DGS [1].

DGS can be modeled by a parallel R, L and C circuit connected to

transmission lines at its both sides as shown in Figure 2.4 [1]. This resistance

corresponds to the radiation, conductor and dielectric losses in the defect. The

size of DGS is determined by accurate curve fitting results for equivalent circuit

Simulation And Analysis Of Defected Ground Structure (DGS) As A Quarter Wavelength At 2.4 GHZ Band.