BIM-UNT-AP6X Magnetic Field Sensor

(1)

Hans Turck GmbH & Co. KG | 45466 Mülheim an der Ruhr, Germany | T +49 208 4952-0 | F +49 208 4952-264 | more@turck.com | www.turck.com 1|4

BIM-UNT-AP6X | 24-05-2023 18-18 | Technical modifications reserved

BIM-UNT-AP6X

Magnetic Field Sensor – For Pneumatic Cylinders

Technical data

Type

BIM-UNT-AP6X

ID 4685720

General data

Pass speed ≤ 10 m/s

Repeatability ≤ ± 0.1 mm

Temperature drift ≤ 0.1 mm

Hysteresis ≤ 1 mm

Electrical data

Operating voltage 10…30 VDC

Residual ripple ≤ 10 % U^ss

DC rated operational current ≤ 150 mA

No-load current 15 mA

Residual current ≤ 0.1 mA

Isolation test voltage ≤ 0.5 kV

Short-circuit protection yes / Cyclic

Voltage drop at I^e ≤ 1.8 V

Wire breakage/Reverse polarity protec-

tion yes / Complete

Output function 3-wire, NO contact, PNP

Switching frequency 1 kHz

Mechanical data

Design Rectangular, UNT

Dimensions 28 x 5 x 6 mm

Housing material Plastic, PP

Active area material Plastic, PP

Tightening torque fixing screw 0.4 Nm

Electrical connection Cable

Features

■

For T-groove cylinders without mounting accessories

■

Optional accessories for mounting on other cylinder designs

■

One-hand mounting possible

■

Stable mounting

■

Magneto-resistive sensor

■

DC 3‐wire, 10…30 VDC

■

NO contact, PNP output

■

Cable connection

Wiring diagram

Functional principle

Magnetic field sensors are activated by magnetic fields and are used, in particular, for the detection of the piston position in pneumatic cylinders. As magnetic fields can permeate non-magnetizable metals, they detect a permanent magnet attached to the piston through the aluminium cylinder wall.

(2)

Technical data

Cable quality Ø 3 mm, Gray, Lif9Y-11Y, PUR, 2 m

Suited for E-ChainSystems® acc. to man- ufacturers declaration H1063M

Core cross-section 3 x 0.14 mm²

Environmental conditions

Ambient temperature -25…+70 °C

Vibration resistance 55 Hz (1 mm)

Shock resistance 30 g (11 ms)

Protection class IP68

MTTF 2283 years acc. to SN 29500 (Ed. 99) 40

°C

Mounting on the following profiles

Cylindrical design ENKF

Switching state LED, Yellow

Included in delivery cable clip

Mounting instructions

Mounting instructions/Description

Thanks to the mounting lip, the sensor can be inserted into the groove from above with one hand. Mount the sensors as follows using the patented wing screw: The wing screw and the female thread feature a left- hand thread. Two small plastic lips keep the screw in position, ready-to-install. Turn the screw clockwise. The screw moves out of the thread and hits the upper grooves with the wings. The sensor is thus pressed down and locked in position. A few degrees up to approximately 1.5 turns of the screw with a slotted screwdriver (blade width 0.5 mm) or a 1.5 mm Allen key are sufficient to ensure vibration-proof fastening, depending on the shape of the slot. A tightening torque of 0.4 Nm is sufficient for safe mounting without damaging the cylinder. The sensor can now withstand an axial and radial tensile load of F=100N applied on the cable. A cable clip is included in the scope of delivery. It enables smooth cable routing in the groove and ensures that the cable is fastened as securely as possible. The corresponding accessories for mounting on other cylindrical housings must be ordered separately.

(3)

Accessories

KLZCD2-UNT 6970418

Mounting bracket for mounting magnetic field sensors for T-grooves on a CleanDesign cylinder with mounting rail

KLZ1-INT 6970410

Accessories for mounting the sensors BIM-INT and BIM-UNT on tie-rod cylinders; cylinder diameter: 32…

40 mm; material: Aluminum; further mounting accessories for other cylinder diameters on request

KLZ2-INT 6970411

Accessories for mounting the sensors BIM-INT and BIM-UNT on tie-rod cylinders; Cylinder diameter: 50…

63 mm; material: Aluminium; Further mounting accessories for other cylinder diameters on request

UNT-STOPPER 4685751

Accessories for finetuning the switchpoint on N T-groove cylinders;

snap-locked in the BIM-UNT fixture;

suited for multiple use; material:

plastic

KLRC-UNT1 6970626

Mounting bracket for mounting magnetic field sensors on round cylinders; cylinder diameter: 8…25 mm; material: PA 6I/6T / nickel silver;

fire-hazard classification acc. to UL94 - V2

KLRC-UNT2 6970627

KLRC-UNT3 6970628

KLRC-UNT4 6970629

Mounting bracket for mounting magnetic field sensors on round cylinders; cylinder diameter: 130…

250 mm; material: PA 6I/6T / nickel silver; fire-hazard classification acc. to UL94 - V2

KLDT-UNT2 6913351

Mounting bracket for mounting magnetic field sensors on dovetail groove cylinders; groove width: 7 mm;

material: PPS

KLDT-UNT3 6913352

Mounting bracket for mounting magnetic field sensors on dovetail groove cylinders; groove width:

9.4 mm; material: PPS

(4)

KLDT-UNT6 6913355

Mounting bracket for mounting magnetic field sensors on dovetail groove cylinders; groove width: 7.35 mm; material: PPS