ii
ABSTRAK
Kekerasan suatu bahan sangat dipengaruhi oleh sifat mekanik dan sifat fisik tersebut pada proses penyambungan dengan menggunakan pengelasan TIG (Tungsten Inert Gas) sifat-sifat tersebut akan berubah akibat pengaruh proses pengelasan. Untuk mengkaji hal tersebut disusunlah sebuah konsep penelitian yang terdiri dari dua tahapan. Pengujian hardness test pada daerah HAZ (Heat Affected Zone) hasil pengelasan, memeriksa struktur mikro hasil pengelasan akibat variasi besaran sudut kampuh V 35º dan 60˚ dari variasi kuat arus 80 A, 90 A dan 100A pada paduan aluminium alloy 6063. Hasil dari pengujian menunjukkan pengelasan dengan variasi kuat arus 80 A, 90 A dan 100A sudut kampuh V 35º pada paduan alumunium alloy 6063 dengan kuat arus pengelasan 80 A nilai kekerasan tertinggi 82.79 kgf/mm sedangkan pada kuat arus 90 A dan 100 A nilai kekerasan yang didapat sama 82.16 kgf/mm. Dan pada paduan aluminium alloy 6063. Hasil dari pengujian menunjukkan pengelasan dengan variasi kuat arus 80 A, 90 A dan 100A sudut kampuh V 60º pada paduan alumunium alloy 6063 dengan kuat arus pengelasan 80 A nilai kekerasan tertinggi 87.25 kgf/mm sedangkan pada kuat arus 90 A dan 100 A nilai kekerasan yang didapat sama 85.98 kgf/mm. Pengujian pada pengelasan TIG (Tungsten Inert Gas) untuk paduan aluminium alloy 6063, menunjukkan Ini menunjukan bahwa semakin kuat arus berpengaruh pada nilai kekerasan daerah HAZ, dan kekerasan rata-rata yang paling baik adalah pada Kuat arus 90 Adan 100 A pada sudut kampuv tungal 35º.
Kata kunci: Kekerasan, hardness test, pengelasan TIG (Tungsten Inert Gas), Sudut Kampuh, aluminium alloy 6063.
iii
ABSTRACT
Hardness of a material is influenced by the nature of the mechanical and physical properties in the splicing process by using TIG welding (Tungsten Inert Gas) these properties will be changed due to the influence of the welding process. To look into the matter was composed of a concept study consisted of two phases. Testing hardness test on HAZ region (Heat Affected Zone) welding results, check the weld microstructure due to variations in the amount of seam V 35º angle and 60˚ of variation of the current strength of 80 A, 90 A and 100A on alloy aluminum alloy 6063. The results of the testing show strong variation welding currents of 80 A, 90 A and 100A angle of 35º to the hem V alloy 6063 with a strong aluminum alloy welding current 80 A high hardness value 82.79 kgf / mm and in the strong currents of 90 A and 100 A hardness value obtained at 82.16 kgf / mm. And aluminum alloys alloy 6063. The results of the testing show strong variation welding currents of 80 A, 90 A and 100A angle of 60º to the hem V alloy 6063 with a strong aluminum alloy welding current 80 A high hardness value 87.25 kgf / mm and in strong currents 90 A and 100 A hardness value obtained at 85.98 kgf / mm. Tests on TIG welding (Tungsten Inert Gas) for alloy aluminum alloy 6063, show This shows that the stronger the effect on the current value of the area HAZ hardness, and the average hardness of the nicest is the Strong current of 100 A at 90 Adan kampuv tungal 35º angle.
Keywords: Violence, hardness test, TIG welding (Tungsten Inert Gas), Angle Kampuh, aluminum alloy 6063.