• Tidak ada hasil yang ditemukan

Week 8 Assignment solution - Nptel

N/A
N/A
Protected

Academic year: 2024

Membagikan "Week 8 Assignment solution - Nptel"

Copied!
3
0
0

Teks penuh

(1)

1. The Newton’s law of viscosity gives the relationship between shear stress to shear rate. It is mathematically expressed as

a) τ= μ b) τ= - μ c) μ= -τ

d) None of the above

ANSWER: b

2. Which of the following can be expressed as a Newtonian fluid?

a) Water b) Oil c) Milk

d) None of the above ANSWER: a

3. For Pseudoplastic fluid, the value of flow behaviour index ‘n’ is a) =1

b) <1 c) >1

d) None of the above ANSWER: b

4. If apparent viscosity is denoted as μ, the equation representing a Bingham plastic fluid is given as

a) τ=μ )n b) τ=μ )n c) τ=μ ) +τy

d) None of these ANSWER: c

(2)

5. The unit of consistency index ‘K’ is a) N.s/m2

b) N.s2/m2 c) N.s2/m d) N.sn/m2 ANSWER: d

6. The pseudolplastic and dilatant fluids are explained by the equation a) τ=μ )n

b) τ=μ ) c) τ=-μ )n d) τ=μ )1/n ANSWER: a

7. Which one of the following is the example of pseudoplastic fluid?

a) Mayonnaise b) Starch suspensions c) Detergent slurries d) All the above ANSWER: d

8. In case of a rheopectic fluid, a) shear stress increases with time b) shear stress decreases with time

c) shear stress increases with rate of shear d) shear stress decreases with rate of shear ANSWER: a

9. A granular material is to be conveyed pneumatically in a line of 20 cm diameter and 100 m long, at the rate of 1500 kg/hr. What will be the mass velocity (mass flux)?

a) 31.26 kg m-2 s-1

(3)

b) 13.26 kg m-2 s-1 c) 1.326 kg m-2 s-1 d) 3.126 kg m-2 s-1

ANSWER: b

G = 13.26 kg m-2 s-1

10. Which of the following statement is correct?

a) Specific volume of fluid is much higher than specific volume of solid b) Specific volume of fluid is much lower than specific volume of solid c) Specific volume of fluid is nearly equal to specific volume of solid d) None of the above

ANSWER: a

Referensi

Dokumen terkait

Based on the numerical results of free convection flow of viscoelastic fluid past over a sphere, we obtained that the velocity profile decreases when we apply

For most pollutants, the average emissions rate for each pollutant decreases as the engine tier increases on both a mass per time and a mass per fuel used basis for both

Off-axis tensile test (a) Strain gauge rosette (b) Shear failure of test specimen (c) Shear stress – strain relationship of the three test specimens. Off-axis Tensile Test

Flow curve of nano-sized silica 10 vol% ER fluid under various electric field strengths: Shear stress a, and shear viscosity b curves as a function of shear rate.. Table 1 CCJ model

Range of shear rate at the field experiment: a lower limits of shear rate b upper limits of shear rate In the fresh cement paste, sample was prepared with 15.5cm of final diameter in

Score: 0 Accepted Answers: i sparsity of effects principle, projection property, sequential experimentation When we estimate A, B, and C with complementary one-half fraction, we are

Finite Element Investigation of Anisotropic Circular Plates Increases in plate thickness do not affect the parabolic distribution with depth of the shear stress.. Similar to the

Meanwhile, the pressure loss in the duct, calciner and cyclone A4 decreases while the percentage degree of calcination increases to up 5.32% with a better heat transfer rate from the