PERLENGKAPAN TERHADAP SIMPANGAN
A.4 PERSYARATAN TERPERINCI UNTUK JEMBATAN TIPE A
A.4.2 PERENCANAAN SENDI DALAM KOLOM BETON STRUKTURAL
A.4.2.1 Umum
Kolom sirkular adalah diutamakan karena keunggulan karakteristik daktailnya. Untuk kolom persegi, perbandingan antara panjang sisi-sisi tidak boleh melebihi 2 terhadap 1 bila dimensi lebih besar berada dalam arah pembebanan gempa. Tidak boleh ada kolom dengan dimensi kurang dari 400 mm (Pustaka B). Tembok yang dibebani dalam arah panjangnya harus direncanakan sesuai ketentuan jembatan tipe C.
A.4.2.2 Regions Where
Special Confining
Reinforcement Should be Provided
(Reference B)Confining hoops should be provided at the ends of pier columns where plastic hinging can occur. This transverse reinforcement should extend for a distance from the point of maximum moment within the region of the hinge given by the maximum of:
i. 1.5 times the column diameter or the maximum cross-sectional dimension.
ii. One sixth (1/6) of the clear height of the column when hinging can occur at both ends of the column. (Type A bridges)
iii. One quarter (1/4) of the clear height of the column when hinging can occur at only one end of the column (as for a cantilever pier). (Type B Bridges and transversely for Type A Bridges with a single stem pier)
iv. 600 mm.
A.4.2.3 Amount of Confining Reinforcement to be
Provided
(Reference B)
Where spirals or closed circular hoop are used the volumetric ratio, defined as:
volume of soiral reinforcement volume of concrete core
should not be less than the greater of:
where:
Ag = is area of section;
Ac = area of core of spirally reinforced member measured to outside of spiral;
f'c = characteristic 28 day cylinder strength of concrete;
f yh = yield strength of binding reinforcement. Where square or rectangular hoop reinforcement is used, the required area of the hoop bars, for each principal direction of the cross section, shall be the greater of:
A.4.2.2
Bagian Untuk Mana Harus Diadakan
Tulangan Pengikal Khusus
(Pustaka B)
Sengkang pengikat harus diadakan pada ujung-ujung kolom pilar dimana sendi plastis dapat terjadi, Penulangan transversal ini harus meliputi suatu jarak terhadap titik momen maksimum didalam daerah sendi sebagai maksimum dari:
i. 1.5 kali diameter kolom atau dimensi potongan melintang maksimum
ii. seperenam (1/6) tinggi bersih dari kolom bila sendi dapat terjadi pada kedua ujung kolorr (jembatan Tipe A)
iii. Seperempat (1/4) tinggi bersih dari kolom bila sendi dapat terjadi hanya pada satu ujung kolom (seperti untuk pilar kantilever). (Jembatan tipe B dan arah transversal untuk jembatan tipe A dengan pilar dinding tunggal)
iv. 600 mm
A.4.2.3 Jumlah Tulangan Pengikat
Yang
Diadakan
(Pustaka B)
Untuk mana spiral atau sengkang sirkular tertutup digunakan, perbandingan volumetrik, ditentukar sebagai:
volume tulanoan spiral volume inti beton
tidak boleh kurang terhadap nilai terbesar dari:
dengan:
Ag = luas penampang
Ac = luas inti dari komponen dengan tulangan spiral, diukur terhadap tepi luar spiral f'c = kekuatan karakteristik silinder beton 28 hari f yh = kekuatan leleh dari tulangan pengikat
Untuk mana tulangan sengkang persegi penuh atau persegi panjang, digunakan luas tulangan sengkang yang diperlukan, untuk tiap arah utama penampang melintang, harus nilai terbesar dari:
where:
Ash = total area of hoop bars anc supplementary cross ties.
sh = centre to centre spacing of hoop and tic sets
hc = dimension of concrete core measurec perpendicular to the direction of the hooF bars to outside of peripheral hoop Supplementary cross ties, where used, should be of the same diameter as the peripheral hoop bar anc should engage the hoop bar with a standard hook The centre to centre spacing of hoop and cross tie sets within the plastic hinges region should not exceed 200 mm or 6 times the diameter of the longitudinal bar.
The centre to centre spacing between cross linked bars across the cross section should not exceed 30C mm. Each longitudinal bar, or bundle of bars, should be laterally supported by the corner of a hoop or by a supplementary cross tie. The following may however be exempted from this requirement:
i. Bars, or bundles of bars, between two laterally supported bars or bundles of bars supported by the same hoop, where the distance between the laterally supported bars or bundles of bars does not exceed 200 mm.
ii. Inner layers of reinforcing bars within the concrete core centred more than 75 mm from the inner face of the hoops.
The yield force in the hoop bar or supplementary cross tie at the specified yield strength, fyh, should be at least equal to one-sixteenth of the yield force in the bar or bars it is to restrain including the contribution from the tributary area of any bar or bars exempted in the previous paragraph.
The binding steel should be either continuous (spiral) over the full height of confinement or be in the form of closed hoops. Continuity of the confining steel should be provided by either:
dengan:
Ash = jumlah luas batang sengkang dan pengikat melintang tambahan
Sh = jarak pusat ke pusat dari susunan sengkang dan pengikat
hc = dimensi inti beton diukur tegak lurus terhadap arah batang sengkang sampai tepi luar sengkang keliling.
Pengikat melintang tambahan, bila digunakan, harus dengan diameter sama seperti batang sengkang keliling dan harus mengikat batang sengkang dengan kait standar. Jarak pusat ke pusat dari susunan sengkang dan pengikat melintang dalam daerah sendi plastis, tidak boleh melebihi 200 mm atau 6 kali diameter batang memanjang.
Jarak pusat ke pusat antara batang-batang yang dihubungkan melintang melalui penampang melintang, tidak boleh melebihi 300 mm. Tiap batang memanjang, atau kumpulan batang, haruss didukunk lateral oleh sudut suatu sengkang atau oleh suatu pengikat melintang tambahan. Yang berikut boleh bagaimanapun dikecualikan dari persyaratan ini: i. Batang, atau kumpulan batang, antara dua batang
yang didukung lateral atau kumpulan batang yang didukung oleh sengkang sama, untuk mana jarak antara batang atau kumpulan batang yang didukung lateral adalah tidak melebihi 200 mm.
ii. Lapis dalam dari batang tulangan dalam inti beton dengan pusat lebih dari 75mm terhadap permukaan dalam dari sengkang
Gaya leleh dalam batang sengkang atau pengikat melintang tambahan pada kekuatan leleh yang dispesifikasi, fyh, harus paling sedikit sama dengan seperenam betas dari gaya leleh dalam batang atau batang-batang yang ditahannya termasuk sumbangun luas tambahan dari setiap batang atau batang-batang yang dikecualikan dalam paragrap sebelumnya.
Baja pengikat harus berupa spiral menerus sepanjang tinggi dari pengikatan atau dalam bentuk sengkang tertutup. Kontinuitas dari baja pengikat harus diadakan dengan salah satu cara:
weld throat thickness should be 0.4 times the bar diameter; or
(b) lapping, where the minimum length of lap should be 30 bar diameter and each end of the bar should be anchored with 135 degree bends with a 10 bar diameter extension into the confined concrete core.
Rectangular hoops should be closed using 135 degree bends extending 10 bar diameters into the concrete core (ref. Figure A.8)
A.4.2.4 Rein forcing Steel
(Reference B)
To ensure adequate ductility, the main longitudinal steel in columns should be either structural steel with a yield stress not exceeding 310 MPa, or reinforcing bar with a maximum yield stress of 450 MPa and a minimum elongation (gauge length 5 d) of 20%. Reinforcement, except ties and stirrups, shall consist of deformed bars.
The column longitudinal steel should not be less than 0.8 percent nor more than 6.0 percent by volume of the concrete core except that in the region of lapped splices the total area should not exceed 8 percent.
A. 4 .2. 5 Con cr ete S tr en g th
(Reference B and 10)
A 28 days concrete cylinder strength of at least 20 MPa is recommended for columns and for members framing into them.
minimum leher las harus sebesar 0,4 kali diameter batang, atau
(b) sambungan penyaluran untuk mana panjang penyaluran minimum harus sebesar 3 0 diameter batang dan tiap ujung batang tersebut harus dijangkar dengan lengkungan 135 derajat dengan kait 10 diameter batang kedalam inti beton yang diikatnya.
Sengkang persegi harus ditutup dengan menggunakan lengkungan 135 derajat yang dikait 10 diameter batang kedalam ini beton What Gambar A.8)
A.4.2.4 Baja Tulangan
(Pustaka B)
Untuk menjamin daktilitas memadai, tulangan memanjang utama dalam kolom harus berupa baja struktural dengan tegangan leleh tidak melebihi 310 MPa, atau batang tulangan dengan tegangan leleh maksimum 450 MPa dan suatu elongasi minimum (panjang gauge 5 d) sebesar 20 %. Penulangan, kecuali pengikat dan sengkang, harus terdiri dari batang deform.
Baja memanjang kolom harus paling sedikit 0.8 % dan tidak lebih dari 6.0 % terhadap volume inti beton kecuali bahwa dalam daerah sambungan penyaluran, luas baja total tidak boleh melebihi 8 %.
A.4.2.5 Kekuatan Beton
(Pustaka B dan 10)
Dianjurkan agar kekuatan beton silinder 28 hari sebesar paling sedikit 20 MPa untuk kolom dan untuk komponen yang bersatu dengannya.
A.4.2.6 In n er Bound Core
(Reference B)
It is recommended that for more important bridges consideration be given to providing the hinge zones with an inner spirally bound core or a structural steel inner core capable of supporting the bridge dead load. Such provisions would ease repair of the plastic hinge region after a major earthquake, by allowing the bridge weight to be supported reliably while damaged concrete and binding is removed and made good
A.4.2.7 Shear
(Reference B)
The maximum shear force to be carried across the plastic hinge region should be calculated as in clause A.4.4.3. For reinforced concrete this shear force should be carried entirely be the transverse reinforcement. Transverse reinforcement provided for confinement may be used as shear reinforcement.
A.4.3 DESIGN OF HINGES IN STRUCTURAL STEEL