UNTUK PEMASANGAN BLOK AAC UNTUK DINDING DALAM DAN DINDING LUAR. ABU-ABU MUDA SEMEN PORTLAND KERING 1,4 KG/L. 3,3 KG/L AIR BERSIH

(1)

TECHNICAL DATA SHEET

BUMA MORTAR

Hal. | 1

SPESIFIKASI PEREKAT BLOK AAC, D-100

THIN BED MORTAR

PENGGUNAAN UNTUK PEMASANGAN BLOK AAC UNTUK DINDING DALAM DAN DINDING LUAR. MANFAAT  VOLUME YANG DIBUTUHKAN LEBIH SEDIKIT, TEBAL APLIKASI 2-4 MM.

 DAPAT MENYELESAIKAN LUAS DINDING HINGGA 16 M²/HARI.  DAPAT MENCAPAI KETINGGIAN HINGGA 3 M/HARI.

 KERAPIAN HASIL AKHIR.  KUAT TEKAN TINGGI. SPESIFIKASI DAN KARAKTERISTIK PRODUK WARNA: PEREKAT: AGREGAT: BAHAN TAMBAHAN: BERAT JENIS: PERBANDINGAN CAMPURAN: KEKUATAN TEKAN: KUAT REKAT METODE TARIK:

DAYA TUTUP:

ABU-ABU MUDA SEMEN PORTLAND

PASIR SILICA DENGAN UKURAN MAKSIMUM 0,6 MM

BAHAN YANG MUDAH LARUT DALAM AIR, MEMPERMUDAH APLIKASI DAN MEMPERBAIKI DAYA REKAT.

KERING 1,4 KG/L. 3,3 KG/L AIR BERSIH

≥ 10 N/MM² SETELAH 28 HARI ≥ 0,5 N/MM² SETELAH 28 HARI

DENGAN MENGGUNAKAN ROSKAM BERGIGI 4MM X 4MM: TEBAL BLOK ( MM ) 75 100 125 150 175 200 PEMAKAIAN UNTUK

BLOK ( KG/M²) 2,4 3,15 4 4,8 5,6 6,4 PEMAKAIAN UNTUK

JUMBO BLOK (KG/M²) 1,7 2,25 3 3,4 4 4,6 APLIKASI  BERSIHKAN PERMUKAAN DARI DEBU DAN KOTORAN-KOTORAN LAINNYA YANG

DAPAT MENGURANGI EFEKTIFITAS PEREKATAN.

 GUNAKAN TEMPAT ADUKAN YANG BERSIH DAN BAIK SEHINGGA CAMPURAN TIDAK LARUT KELUAR DARI TEMPATNYA.

 TUANGKAN L-100 SECARA BERTAHAP KE DALAM AIR. ADUK SELAMA 2 MENIT HINGGA MERATA SAMPAI DIPEROLEH KONSISTENSI, BIARKAN 10 MENIT SUPAYA ADITIV LARUT. ADUK KEMBALI SEBELUM DIGUNAKAN.

 SEBAIKNYA MENGGUNAKAN ALAT PENGADUK ELEKTRIK (MIXER).  GUNAKAN ROSKAM BERGIGI YANG SESUAI DENGAN KETEBALAN BLOK.

 PASANGAN DILETAKKAN PADA SISI HORIZONTAL DAN VERTIKAL BLOK SECARA MERATA DENGAN KETEBALAN 2-3 MM.

 TUTUP SAMBUNGAN ANTAR BLOK YANG TIDAK MERATA / BERONGGA DENGAN ADUKAN MORTAR.

PENYIMPANAN SIMPAN DI TEMPAT YANG RATA, TERTUTUP DAN KERING. BAIK DIGUNAKAN HINGGA 6 BULAN.

(2)

TECHNICAL DATA SHEET

BUMA MORTAR

Hal. | 2

SPESIFIKASI PLASTERAN, D-200

RENDER PLASTER

USAGE

FOR SMOOTHER PLASTER WITHOUT SKIMMED COAT. FOR INTERNAL & EXTERNAL WALL APPLICATION

ADVANTAGES  SUITABLE FOR AAC BLOCKS & WALL PANEL APPLICATION  SMOOTHER SURFACE, NO FINE COAT NEEDED

 GOOD CONSISTENCY OF THE MIXTURE.  QUICK AND EASY TO WORK WITH.  GOOD BONDING STRENGTH  REDUCE COST SPECIFICATIONS AND PROPERTIES TYPE: COLOUR: AGGREGATE BINDER: ADDITIVES: WATER DEMAND DRY DENSITY: COMPRESSIVE STRENGTH: COVERAGE AREA: POWDER LIGHT GREY SILICA SAND PORTLAND CEMENT

WATER-SOLUBLE ADDITIVE TO IMPROVE

WORKABILITY AND GOOD BONDING STRENGTH. 1.5 – 1.6 KG/LTR

4.76 KG/LTR OF WATER 5 – 7 N/MM²

19 KG/SQM FOR 10 MM THICKNESS OF PLASTER

APPLICATION  CLEAN THE SURFACES FROM DUST, DIRT, AND OTHER MATERIALS THAT MAY EFFECT THE BONDING STRENGTH.

 USE A CLEAN AND LEAK-PROOF PAIL FOR MIXING.

 PUT PM-200+ GRADUALLY INTO THE WATER AND MIX THOROUGHLY

AROUND 2 MINUTES UNTIL AN EVEN CONSISTENCY OF MIXTURE. WAIT FOR 10 MINUTES FOR ADDITIVES TO DISSOLVE. RE-STIR BEFORE APPLICATION. THE MIXTURE WILL BE STABLE FOR 3 HOURS.

 PLASTERING JOB COULD BE DONE AFTER 24 HOURS ERECTING WALL WITH BLOCKS OR WALL PANELS. AND AFTER D-100 APPLICATION FINISHED.

STORAGE

STORE IN DRY PLACE AWAY FROM CONTACT WITH MOISTURE AND WATER. D-200+ STORAGE TIMES SHOULD NOT EXCEED 6 MONTHS.

(3)

TECHNICAL DATA SHEET

BUMA MORTAR

Hal. | 3

SPESFIKASI ACIAN, D-300

FINE COAT

PRODUK D-300 FINE COAT CARA PEMAKAIAN PERSIAPAN

 BERSIHKAN PERMUKAAN DINDING PLESTER YANG AKAN DIAPLIKASIKAN D-300 DARI DEBU, MINYAK, KARAT, MAUPUN KOTORAN/SERPIHAN LAINNYA YANG DAPAT MENGURANGI REKATAN ADUKAN KEMUDIAN BASAHI DENGAN AIR.

PENGADUKAN

 TABURKAN SEDIKIT DEMI SEDIKIT POWDER D-300 KE DALAM WADAH YANG TELAH BERISI AIR (LIHAT PETUNJUK PEMAKAIAN AIR) LALU DIADUK HINGGA MERATA GUNA MENGHINDARI TERJADINYA GUMPALAN.

 DAN AKAN LEBIH BAIK JIKA MENGGUNAKAN ELECTRICAL MIXER DRILL (± 500 RPM) YANG TELAH DILENGKAPI DENGAN PADDLE (PENGADUK).

APLIKASI

 SEBELUM DIAPLIKASIKAN SEBAIKNYA PERMUKAAN DINDING PLESTER YANG TERSEDIA DALAM KEADAAN SSD (SATURATED SURFACE DRY).

 APLIKASIKAN ADUKAN D-300 DENGAN CARA MENGHAMPAR PADA BIDANG YANG TERSEDIA DENGAN MENGGUNAKAN TROWEL.

 LAKUKAN PENGHAMPARAN PADA LAPIS BERIKUTNYA UNTUK MENDAPATKAN HASIL YANG OPTIMAL DAN JIKA DIRASA PADA PENGHAMPARAN PERTAMA KURANG MEMADAI.

 PASTIKAN PERMUKAAN BIDANG DALAM KEADAAN SETENGAH KERING LALU LAKUKAN “FINISHING” DENGAN MENGGUNAKAN TROWEL UNTUK MENDAPATKAN HASIL YANG HALUS DAN RATA. TEBAL APLIKASI YANG DIANJURKAN ADALAH 1.5 – 3.0 MM.

(SEBAIKNYA TARIKAN TROWEL SAAT FINISHING SELAIN TIDAK DITEKAN JUGA DILAKUKAN SEARAH DAN JANGAN MENGGUNAKAN KERTAS SEMEN UNTUK MENGGOSOK).

PREPARATION

 SUBSTRATE MUST BE FREE OF DIRT, OIL, RUST, AND OTHER FOREIGN MATERIALS. MIXING

 POUR GARDUALLY D-300 POWDER INTO A CONTAINER CONTAINING CLEANED WATER (12-13 LITER OF WATER FOR 40 KG OF D-300).

 MIX UNTIL THE POWDER AND WATER ARE COMPLETELY BLENDED. IT IS RECOMMENDED TO USE HAND MIXER.

APPLICATION

 WALL SURFACE SHOULD BE MOIST WELL OR IN SSD CONDITION (SATURATED SUFACE DRY).

 APPLICATION FOR FINE COAT IS AT LEAST 1X24 HOURS AFTER PLASTERING.

 SPREAD OUT D-300 UNIFORMLY ON ALREADY CLEANED AND MOISTENED SURFACE USING A SUITABLE.

(4)

TECHNICAL DATA SHEET

BUMA MORTAR

Hal. | 4

 ENSURE THE SURFACE BECOME HALF-DRY THEN SMOOTH IT USING EVEN TROWEL

TO MAKE THE SURFACE FLAT AND SMOOTH. THE RECOMMENDED THICKNESS IS 1.5-3 MM.

 IN ORDER TO HAVE A GOOD PAINTING, USE WALL PUTTY PRIME MORTAR PM-315.

APPLICATION METHOD

PREPARATION

 SUBSTRATE MUST BE FREE OF DIRT, OIL, RUST, AND OTHER FOREIGN MATERIALS. MIXING

 POUR GARDUALLY D-300 POWDER INTO A CONTAINER CONTAINING CLEANED WATER (12-13 LITER OF WATER FOR 40 KG OF D-300).

 MIX UNTIL THE POWDER AND WATER ARE COMPLETELY BLENDED. IT IS RECOMMENDED TO USE HAND MIXER.

APPLICATION

 WALL SURFACE SHOULD BE MOIST WELL OR IN SSD CONDITION (SATURATED SUFACE DRY).

 APPLICATION FOR FINE COAT IS AT LEAST 1X24 HOURS AFTER PLASTERING.

 SPREAD OUT D-300 UNIFORMLY ON ALREADY CLEANED AND MOISTENED SURFACE USING A SUITABLE.

 REPEAT IT TO THE FOLLOWING LAYER UNTIL THE OPTIMUM RESULT IS MET.

 ENSURE THE SURFACE BECOME HALF-DRY THEN SMOOTH IT USING EVEN TROWEL TO MAKE THE SURFACE FLAT AND SMOOTH. THE RECOMMENDED THICKNESS IS 1.5-3 MM.

(5)

TECHNICAL DATA SHEET

BUMA MORTAR

Hal. | 5

SPESIFIKASI PEREKAT KERAMIK BEBAN DINAMIS, L-405

HEAVY DUTY TILE ADHESIVE

USES HEAVY DUTY TILE ADHESIVE IS AN ADHESIVE BONDING CERAMIC TILE ON WOOD, STEEL, OR SURFACE WITH DYNAMIC LOAD.

ADVANTAGES  GOOD CONSISTENCY OF THE MIXTURE.  QUICK AND EASY TO WORK WITH.

 EXCELLENT FLEXIBILITY TO REDUCE HAIR-CRACK.  GOOD BONDING STRENGTH.

 REDUCE COST. SPECIFICATIONS AND PROPERTIES TYPE: COLOUR: BINDER: AGGREGATE: ADDITIVES: DRY DENSITY: WET DENSITY: LIQUID DEMAND: OPEN TIME: WATER RETENTION: ADHESION STRENGTH ( PULL OFF ) COMPRESSIVE STRENGTH: FLEXURAL STRENGTH: THICKNESS FOR APPLICATION: COVERAGE AREA: POWDER + LIQUID DARK GREY PORTLAND CEMENT

SILICA SAND UP TO 0.6 MM MAXIMUM SIZE WATER-SOLUBLE ADDITIVE TO IMPROVE WORKABILITY, AND TENSILE ADHESION STRENGTH.

1.7 KG/L 1.9 KG/L

13.2 – 13.5 L/40 KG

10 – 15 MINUTES, ON EVEN SURFACE > 95 % ( BS 4551 : 1980 ) > 2.0 N/MM²AFTER 28 DAYS ( EN 1348 : 1999 ) > 15 N/MM² AFTER 28 DAYS > 7 N/MM² AFTER 28 DAYS 3 – 7 MM ± 8 M²/40 KG/3 MM

APPLICATION - CLEAN THE SURFACES FROM DUST, DIRT, AND OTHER MATERIALS THAT MAY EFFECT THE BONDING STRENGTH.

- USE A CLEAN AND LEAKPROOF PAIL FOR MIXING.

- GRADUALLY PUT POWDER PM-405 INTO THE WATER AND MIX

THOROUGHLY UNTIL AN EVEN CONSISTENCY IS ACHIEVED FOR AROUND 2 MINUTES, ALLOW TO BE SETTLED FOR 10 MINUTES FOR ADDITIVES TO DISSOLVE. RE-STIR BEFORE USING. THE MIXTURE WILL BE STABLE FOR 3 HOURS.

- RE-STIR THE PASTA REGULARLY, BUT DO NOT ADD MORE WATER OR LIQUID PM-405.

- MACHINE MIXING IS HIGHLY RECOMMENDED.

STORAGE ALWAYS STRORE IN DRY PLACE AWAY FROM CONTACT WITH MOISTURE AND WATER.

(6)

TECHNICAL DATA SHEET

BUMA MORTAR

Hal. | 6

PACKAGING MULTI LAYER PAPER BAG CONTAINING 40 KG.

HEAVY DUTY TILE ADHESIVE PM-405 STORAGE TIMES SHOULD NOT EXCEED 12 MONTHS.

(7)

TECHNICAL DATA SHEET

BUMA MORTAR

Hal. | 7

SPESIFIKASI PEREKAT KERAMIK DAERAH BASAH, L-410

WET AREA TILE ADHESIVE

PRODUK L-410

EXTERIOR & WET INTERIOR TILE ADHESIVE CARA

PEMAKAIAN

PERSIAPAN

 UMUR LANTAI BETON BARU HARUS SEKURANG-KURANGNYA 28 HARI.

 BERSIHKAN PERMUKAAN YANG AKAN DIAPLIKASIKAN L-410 DARI DEBU, MINYAK, KARAT,

CURING AGENTS

, MAUPUN KOTORAN LAINNYA YANG DAPAT MENGURANGI REKATAN. JANGAN RENDAM KERAMIK KE DALAM AIR!

PENGADUKAN

 TABURKAN SEDIKIT DEMI SEDIKIT BAGIAN POWDER L-410 KE DALAM WADAH YANG TELAH BERISI AIR (10-11 LITER AIR BERSIH UNTUK 40 KG L-410) LALU DIADUK HINGGA MERATA GUNA MENGHINDARI TERJADINYA GUMPALAN.

 DISARANKAN UNTUK MENGGUNAKAN ELECTRICAL MIXER DRILL (± 500 RPM) YANG TELAH DILENGKAPI DENGAN

PADDLE

(PENGADUK). (JANGAN MENAMBAHKAN AIR KE DALAM ADUKAN)

APLIKASI

 SEBELUM APLIKASI SEBAIKNYA PERMUKAAN BIDANG YANG TERSEDIA DAN DASAR PERMUKAAN KERAMIK DALAM KEADAAN SSD (

SATURATED SURFACE DRY

).

 OLESKAN ADUKAN PEREKAT PADA PERMUKAAN YANG TELAH DIPERSIAPKAN DENGAN MENGGUNAKAN TROWEL BERGIGI (JENIS TROWEL BERGIGI DISESUAIKAN DENGAN UKURAN KERAMIK YANG DIPASANG). SETIAP PERLETAKAN ADUKAN JANGAN MELEBIHI 1 M².

 PASANGLAH KERAMIK PADA LAPISAN PEREKAT YANG MASIH BASAH DENGAN DIBERI TEKANAN SAMPAI KERAMIK MASUK CUKUP DALAM PADA LAPISAN PEREKAT SEHINGGA DAPAT DIPASTIKAN PEMASANGAN YANG OPTIMAL.

 UNTUK JENIS KERAMIK YANG TEBAL ATAU QUARRY DENGAN BAGIAN BELAKANG YANG TIDAK RATA DIANJURKAN UNTUK MENGOLESI DAHULU DENGAN PEREKAT UNTUK MEMBANTU PENYEBARAN DAN PENGIKATAN SECARA SEMPURNA PADA PEMASANGAN KERAMIK.

 GUNAKAN TILE SPACER PADA SETIAP PERTEMUAN SUDUT KERAMIK DISELURUH LANTAI DAN DINDING.

 HINDARILAH LALU LINTAS DI ATAS LANTAI PADA PEKERJAAN PEMASANGAN KERAMIK LANTAI SEKURANG-KURANGNYA 24 JAM SETELAH KERAMIK TERPASANG.  SETELAH 24 JAM KERAMIK TERPASANG GUNAKAN SALAH SATU WARNA BAHAN

PENGISI NAT PM-500.

PREPARATION

 NEW CONCRETE SHOULD BE AT LEAST 28 DAYS OLD.

 BOTH NEW AND OLD CONCRETE MUST BE STRUCTURALLY SOUND, CLEAN, AND FREE FROM CONTAMINANTS IN ORDER TO OBTAIN A GOOD BOND. MAKE THE SURFACE MOUISTURE BEFORE APPLICATION. DO NOT SINK THE TILES INTO THE WATER.

MIXING

 GRADUALLY ADD 40 KG BAG OF L-410 INTO APPROXIMATELY 10-11 LITERS OF WATER AND MIX WELL USING A HAND-HELD DRILL MIXER WITH LOW SPEED (±500 RPM) UNTIL A HOMOGENEOUS LUMP-FREE MIX IS OBTAINED.

APPLICATION

 THE SURFACE MUST BE MOIST WELL OR IN SSD CONDITION (SATURATED SUFACE DRY).

(8)

TECHNICAL DATA SHEET

BUMA MORTAR

Hal. | 8

 LAY DOWN THE MIXTURE OF L-410 USING A NOTCHED TROWEL. THE LAID MIXTURE

SHOULD NOT BE MORE THAN 1 SQM.

 PUT EACH TILE ONTO THE SURFACE AND THEN PUSH IT MODERATELY TO ENSURING THE TILE BONDING WELL.

 FOR MARBLE OR QUARRY TILES WHICH HAS UNEVEN BACK, POUR THE MIXTURE ON ITS BACK BODY BEFORE LAYING TILES.

 DO NOT PASS ON THE INSTALLED TILES AT LEAST FOR 24 HOURS.  FILL THE GAB OF TILES AFTER 24 HOURS.

 IT IS RECOMMENDED TO USE L-500 TO FILLING THE GAB BETWEEN TILES.

APPLICATION PREPARATION

MIXING

 GRADUALLY ADD 25 KG BAG OF L-410 INTO APPROXIMATELY 6.25 – 7 LITERS OF WATER AND MIX WELL USING A HAND-HELD DRILL MIXER WITH LOW SPEED (±500 RPM) UNTIL A HOMOGENEOUS LUMP-FREE MIX IS OBTAINED.

APPLICATION

 THE SURFACE MUST BE MOIST WELL OR IN SSD CONDITION (SATURATED SUFACE DRY).

 LAY DOWN THE MIXTURE OF L-410 USING A NOTCHED TROWEL. THE LAID MIXTURE SHOULD NOT BE MORE THAN 1 SQM.

(9)

TECHNICAL DATA SHEET

BUMA MORTAR

Hal. | 9

SPESIFIKASI PEREKAT KERAMIK DAERAH KERING, L-420

DRY AREA TILE ADHESIVE

PRODUK L-420

DRY INTERIOR TILE ADHESIVE CARA

PEMAKAIAN

PERSIAPAN

 UMUR LANTAI BETON BARU HARUS SEKURANG-KURANGNYA 28 HARI.

 BERSIHKAN PERMUKAAN YANG AKAN DIAPLIKASIKAN L-420 DARI DEBU, MINYAK, KARAT,

CURING AGENTS

, MAUPUN KOTORAN LAINNYA YANG DAPAT

MENGURANGI REKATAN. JANGAN RENDAM KERAMIK KE DALAM AIR! PENGADUKAN

 TABURKAN SEDIKIT DEMI SEDIKIT BAGIAN POWDER L-420 KE DALAM WADAH YANG TELAH BERISI AIR (10-11 LITER AIR BERSIH UNTUK 40 KG L-420) LALU DIADUK HINGGA MERATA GUNA MENGHINDARI TERJADINYA GUMPALAN.  DISARANKAN UNTUK MENGGUNAKAN ELECTRICAL MIXER DRILL (± 500 RPM)

YANG TELAH DILENGKAPI DENGAN PADDLE (PENGADUK). (JANGAN MENAMBAHKAN AIR KE DALAM ADUKAN)

APLIKASI

 SEBELUM APLIKASI SEBAIKNYA PERMUKAAN BIDANG YANG TERSEDIA DAN DASAR PERMUKAAN KERAMIK DALAM KEADAAN SSD (

SATURATED SURFACE

DRY

).

 OLESKAN ADUKAN PEREKAT PADA PERMUKAAN YANG TELAH DIPERSIAPKAN DENGAN MENGGUNAKAN TROWEL BERGIGI (JENIS TROWEL BERGIGI DISESUAIKAN DENGAN UKURAN KERAMIK YANG DIPASANG). SETIAP PERLETAKAN ADUKAN JANGAN MELEBIHI 1 M².

 PASANGLAH KERAMIK PADA LAPISAN PEREKAT YANG MASIH BASAH DENGAN DIBERI TEKANAN SAMPAI KERAMIK MASUK CUKUP DALAM PADA LAPISAN PEREKAT SEHINGGA DAPAT DIPASTIKAN PEMASANGAN YANG OPTIMAL.

 UNTUK JENIS KERAMIK YANG TEBAL ATAU QUARRY DENGAN BAGIAN BELAKANG YANG TIDAK RATA DIANJURKAN UNTUK MENGOLESI DAHULU DENGAN PEREKAT UNTUK MEMBANTU PENYEBARAN DAN PENGIKATAN SECARA SEMPURNA PADA PEMASANGAN KERAMIK.

 GUNAKAN TILE SPACER PADA SETIAP PERTEMUAN SUDUT KERAMIK DISELURUH LANTAI DAN DINDING.

 HINDARILAH LALU LINTAS DI ATAS LANTAI PADA PEKERJAAN PEMASANGAN KERAMIK LANTAI SEKURANG-KURANGNYA 24 JAM SETELAH KERAMIK TERPASANG.

 SETELAH 24 JAM KERAMIK TERPASANG GUNAKAN SALAH SATU WARNA BAHAN PENGISI NAT L-500.

MIXING

 GRADUALLY ADD 40 KG BAG OF L-420 INTO APPROXIMATELY 10-11 LITERS OF WATER AND MIX WELL USING A HAND-HELD DRILL MIXER WITH LOW SPEED (±500 RPM) UNTIL A HOMOGENEOUS LUMP-FREE MIX IS OBTAINED.

(10)

TECHNICAL DATA SHEET

BUMA MORTAR

Hal. | 10

 THE SURFACE MUST BE MOIST WELL OR IN SSD CONDITION (SATURATED SUFACE

DRY).

 LAY DOWN THE MIXTURE OF L-420 USING A NOTCHED TROWEL. THE LAID MIXTURE SHOULD NOT BE MORE THAN 1 SQM.

(11)

TECHNICAL DATA SHEET

BUMA MORTAR

Hal. | 11

SPESIFIKASI PENGISI NUT KERAMIK, L-500

TILE GROUT

PRODUK L-500 TILE GROUT CARA PEMAKAIAN PERSIAPAN

 PASTIKAN BAHWA PEREKAT UBIN TELAH KERING SEMPURNA SEBELUM MELAKUKAN PEKERJAAN PENGISIAN CELAH NAT DIANTARA UBIN (MINIMAL DILAKUKAN SETELAH 24 JAM UBIN TERPASANG).

 BERSIHKAN CELAH UBIN DARI SISA PEREKAT, MINYAK, KARAT, LUMUT MAUPUN BENDA-BENDA LEPAS LAINNYA.

 BILA UBIN DISENTUH TERASA PANAS DAN PEKERJAAN PENGISIAN NAT

DILAKUKAN PADA SUHU DI ATAS 32ºC SEYOGYANYA DILAKUKAN PENDINGINAN DENGAN CARA MENYEKA PERMUKAAN UBIN DENGAN MENGGUNAKAN KAIN LEMBAB (BUKAN BASAH).

PENGADUKAN

 TABURKAN SEDIKIT DEMI SEDIKIT POWDER L-500 KE DALAM SEBUAH WADAH YANG TELAH BERISI AIR (LIHAT PETUNJUK PEMAKAIAN AIR) LALU DIADUK HINGGA MERATA GUNA MENGHINDARI TERJADINYA GUMPALAN.

 DAN AKAN LEBIH BAIK JIKA MENGGUNAKAN

ELECTRICAL MIXER DRILL

(± 500 RPM) YANG TELAH DILENGKAPI DENGAN

PADDLE

(PENGADUK).

APLIKASI

 OLESKAN BAHAN PENGISI NAT DENGAN MENGGUNAKAN ROSKAM KARET

(

RUBBER SQUEEGEE

) PADA CELAH UBIN LALU LAKUKAN DENGAN GERAKAN

DIAGONAL ATAU MEMUTAR SAMPAI SELURUH CELAH DIANTARA UBIN DAPAT TERISI PENUH DENGAN BAHAN PENGISI NAT.

 UNTUK BAHAN PENGISI NAT YANG BERLEBIHAN AGAR DIBERSIHKAN DARI PERMUKAAN UBIN DENGAN ALAT YANG SAMA SAMBIL PEKERJAAN PENGISIAN BERLANGSUNG.

 JIKA TERDAPAT BAHAN PENGISI NAT YANG MULAI MENGERING PADA PERMUKAAN UBIN HENDAKLAH DIBERSIHKAN/DIBUANG DENGAN MENGGUNAKAN KARET BUSA LEMBAB (BUKAN BASAH).

 AGAR PEKERJAAN LEBIH SEMPURNA DAPAT MENGGUNAKAN JARI YANG TELAH DILINDUNGI DENGAN SARUNG TANGAN UNTUK MENGGOSOK SELURUH CELAH UBIN YANG TELAH TERISI DENGAN BAHAN PENGISI NAT SEHINGGA DIPEROLEH PENGISIAN YANG PADAT, MERATA SEMPURNA DAN HALUS.

 AFTER INSTALLING TILES, WAIT FOR AT LEAST 24 HOURS BEFORE GROUTING JOINTS.

 ENSURE ALL LOOSE MATERIAL, HARDENED TILE ADHESIVE MATERIAL AND OTHER CEMENT CONTAMINANT ON TILE SURFACE OR EDGES ARE REMOVED BEFORE GROUTING WORK.

 ENSURE PUDDLE WATER IS WIPED DRY BEFORE GROUTING WORK. MIXING

 GRADUALLY ADD 25 KG BAG OF L-500 INTO APPROXIMATELY 9 LITERS OF WATER AND MIX WELL USING A HAND-HELD DRILL MIXER WITH LOW SPEED (±500 RPM) UNTIL A HOMOGENEOUS LUMP-FREE MIX IS OBTAINED.

APPLICATION

 SPREAD AND PUSH THE MIXTURE INTO TILE JOINTS WITH RUBER SQUEEGEE IN DIAGONAL DIRECTIONS TO THE TILE GROUT LINES. THIS ENSURES JOINT ARE

(12)

TECHNICAL DATA SHEET

BUMA MORTAR

Hal. | 12

COMPLETELY FILLED. IMPROPERLY GROUTED JOINTS CONTAINING AIR VOID

WOULD CAUSE SINKING OF GROUT MATRIAL AND CRACKING OF TILE GROUT.  REMOVE EXCESS MATERIAL WITH EDGE OF RUBBER FLOAT AND WORK THE FLOAT

IN DIAGONAL DIRECTIONS AS WORK PROGRESES. USE A GLOVED FINGER TO RUN ALONG THE JOINTS TO ENSURE PERFECTLY SMOOTH EVEN FINISHING.

 ONCE THE GROUT IS FIRM, CLEAN THE TILE SURFACE WITH MOISTENED SPONGE OR CLOTH, NOT THE WET ONE.

 ALLOW GROUT MATERIAL TO DRY AND SET ABOUT 2-4 HOURS. IN FINAL

CLEANING STEP, CAREFULLY POLISH TILE SURFACE WITH A CLEAN SOFT CLOTH OR SPONGE PAD TO REMOVE THE POWDERY HAZE ON TILE SURFACE.

(13)

TECHNICAL DATA SHEET

BUMA MORTAR

Hal. | 13

SPESIFIKASI PERATA LANTAI, L-600

SCREED

USES PREMIUM SCREED IS A BLENDED MORTAR PERFORMED TO FILLING GAP OF FLOOR PANEL, LEVELLING FLOOR SURFACE, AND STRENGTHENING SURFACE AS TOPPING MATERIAL.

ADVANTAGES  GOOD CONSISTENCY OF THE MIXTURE.  QUICK AND EASY TO WORK WITH.  EXCELLENT COMPRESSIVE STRENGTH.

 VERSATILE FOR BOTH GROUTING AND SCREEDING.  DURABLE TO FLUCTUATIVE TEMPERATURE.

 SUITABLE TO BOTH INTERNAL AND EXTERNAL WALL APPLICATION. SPECIFICATION AND PROPERTIES TYPE: COLOUR: BINDER: AGGREGATE: DRY DENSITY: WET DENSITY: WATER DEMAND: OPEN TIME: ADHESION STRENGTH ( PULL OFF ): COMPRESSIVE STRENGTH: FLEXURAL STRENGTH: THICKNESS OF APPLICATION: COVERAGE AREA: POWDER LIGHT GREY PORTLAND CEMENT

SILICA SAND UP TO 5.0 MM OF DIAMETER 1.8 KG/L

1.9 KG/L

6.5 – 7.0 LITER PER 40 KG BAG.

10 – 15 MINUTES ( ON EVEN WEATHER ) > 0.6 N/MM² AFTER 28 DAYS

> 20 N/MM² AFTER 28 DAYS > 5 N/MM² AFTER 28 DAYS

± 20 MM

± 1.5 M²/40 KG/20MM ( ON EVEN SURFACES ) PREPARATION - SUBSTRATE MUST BE FREE OF DUST, OIL, RUST AND OTHER FOREIGN

MATERIALS.

- POUR GRADUALLY L-600 INTO A CONTAINER CONTAINING CLEAN WATER ( 6 – 6.5 LITER OF WATER FOR 40 KG L-600 ). THEN MIX UNTIL THEY ARE

COMPLETELY BLENDED. IT IS RECOMMENDED TO USE HAND MIXER. APPLICATION - SPREAD OUT L-600 ON ALREADY CLEANED AND MOISTENED SURFACE.

- ENSURE ALL GAP IS FULFILLED WELL USING TROWEL OR VIBRATOR. - MAKE THE SURFACE EVEN USING FLAT TROWEL.

STORAGE AND PACKAGING

ALWAYS STORE IN DRY PLACE AWAY FROM CONTACT WITH MOISTURE AND WATER. PREMIUM SCREED L-600 STORAGE TIME SHOULD NOT EXCEED 12 MONTH.

(14)

TECHNICAL DATA SHEET

BUMA MORTAR

Hal. | 14

SPESIFIKASI PENGERAS PERMUKAAN LANTAI, L-700

FLOOR HARDENER

USES FLOOR HARDENER IS HEAVY-DUTY HARDENER THAT PRODUCES DENSE, HARD SURFACES ON HORIZONTAL CONCRETE AND IMPROVES SLIP

RESISTANCE IN PEDESTRIAN AND VEHICULAR TRAFFIC AREAS. TIME-TESTED AND PROVEN, IT IS AVAILABLE IN A WIDE RANGE OF PERMANENT, UNIFORM, STREAK-FREE COLORS OR UNCOLORED, FOR ALL TYPES OF FLATWORK SUBJECT TO WAREHOUSE, WORKSHOP, PARKING PLACE, PETROL PUMP, GARAGE, BUTCHERY, AGRICULTURE BUILDING, LOADING OR UNLOADING AREA, TENNIS HALL, AND OTHER COMMERCIAL FLOORS.

ADVANTAGES  GOOD CONSISTENCY OF THE MIXTURE.  QUICK AND EASY TO WORK WITH.  ABRASION RESISTANCE.

 GOOD COMPRESSIVE STRENGTH.

 DURABLE TO FLUCTUATING TEMPERATURE.

 CAN BE APPLIED WITH BOTH OF HAND TROWEL OR THE POWER TROWELING MACHINE WITH FLOAT BLADES (SHOES).

SPECIFICATION AND PROPERTIES TYPE: COLOUR: BINDER: AGGREGATE: ADDITIVES: DRY DENSITY: WET DENSITY: OPEN TIME: ADHESION STRENGTH ( PULL OFF ): COMPRESSIVE STRENGTH: HARDNESS: ABRASION RESISTANCE TO PLAIN CONCRETE FLOOR : COVERAGE AREA:

POWDER

NATURAL, GREEN, RED, YELLOW AND ORANGE.

PORTLAND CEMENT

SILICA SAND UP TO 1.2 MM MAXIMUM SIZE WATER SOLUBLE ADDITIVES TO IMPROVE WORKABILITY, DURABILITY AND BONDING 1.7 KG/L

1.8 KG/L

10 – 15 MINUTES ( ON EVEN WEATHER ) > 1.0 N/MM² AFTER 28 DAYS

> 60 N/MM² AFTER 28 DAYS 6 – 7 MOH’S SCALE

> 200 %

5 – 6 KG / M² / 3 MM

PREPARATION  ADJACENT CONCRETE SURFACES SHOULD BE PROTECTED BY PLASTIC SHEETING DURING APPLICATION AND FINISHING OF THE FLOOR HARDENER.  BRIDGE MAY BE NEEDED FOR WIDER AREAS DURING THE INITIAL

APPLICATION OF L-700.

APPLICATION  POUR L-700 ON A HALF DRY CONCRETE UNIFORMLY.

 THE SURFACEOF L-700 BECOME IN MOISTENED CONDITION FOR LIQUID CONTENT OF MIXTURES.

(15)

TECHNICAL DATA SHEET

BUMA MORTAR

Hal. | 15

 TO DEVELOP PROPER STRENGTH AND MONOLITHIC BONDING, THE

NECESSARY MOISTURE FOR WETTING THE FLOOR HARDENER MUST COME FROM THE CONCRETE SUBSTRATE. WATER MUST NOT BE SPRINKLED OR OTHERWISE ADDED THE SURFACE DURING APPLICATION, SINCE REDUCE DURABILITY AND DISCOLORED, WEAKENED SURFACE MAY OCCUR.  AWAIT A MINUTE UNTIL ALL PART AREA IS MOISTENED, THEN FLOATING

THE SURFACE BY HAND OR MACHINE TROWEL. HAND FLOATS MAY BE USED FOR FLOATING SMALLER PROJECTS OR, WHEN USING A POWER TROWELING MACHINE, FOR EDGES AND OTHER AREAS THAT CANNOT BE REACHED BY THE MACHINE. SUBSEQUENT APPLICATIONS MAY BE FLOATED OR TROWELED WITH POWER EQUIPMENT.

 AFTER FLOATING THE FINAL SHAKE, THE SURFACE SHOULD BE MACHINE OR HAND TROWELED. TO PREVENT BURNING OR DARKENING OF THE SURFACE, HARD STEEL TROWELING (BURNISHING) SHOULD BE MINIMIZED, ESPECIALLY AT THE EDGES AND JOINT LINES.

 THE SPECIFIED TEXTURE SHOULD BE APPLIED UNIFORMLY USING

CONSISTENT FINISHING PRACTICES. ALL SURFACES SHOULD BE FINISHED WITHIN REASONABLY THE SAME TIME AFTER PLACING. ON TROWELED FLAT INTERIOR FLOORS, FINAL HAND-TROWELING SHOULD BE DONE IN A

CONSISTENT DIRECTION AND UNIFORMLYSO THAT THE CURED SURFACE WILL NOT SLIPPERY. A SLIP-REISTANT, FLAT TROWELED FINISH IS

SUGGESTED.

 WHEN WEAKENED-PLANE JOINTS ARE TO BE SAW-CUT, THE USE OF DRY-CUT SAW IS SUGGESTED WITHIN THE FIRST FEW HOURS AFTER CONCRETE PLACEMENT.

STORAGE AND PACKAGING

ALWAYS STORE IN DRY PLACE AWAY FROM CONTACT WITH MOISTURE AND WATER.

FLOOR HARDENER L-700 STORAGE TIMES SHOULD NOT EXCEED 12 MONTH. MULTI LAYER PAPER BAG CONTAINING 40 KG.

(16)

TECHNICAL DATA SHEET

BUMA MORTAR

Hal. | 16

SPESIFIKASI CAIRAN ADESIV, L-800

BONDING AGENT

USES BONDING AGENT IS A COPOLYMER ACRYLIC STYRENE WHICH IS FORMULATED AS A BONDING AGENT FOR CEMENTITIOUS MORTARS AND TOPPINGS ON THE SURFACES SUCH AS CONCRETE, STEEL, AND AAC BLOCK, OR AS AN

ADMIXTURE TO INCREASE BONDING PERFORMANCE. BONDING AGENT IS ALSO SUITABLE TO REPAIR CRACKS ON MANSONRY WALL AND CONCRETE FLOOR.

 REDUCE COST. SPECIFICATIONS AND PROPERTIES TYPE: COLOUR: BINDER: AGGREGATE: ADDITIVES: DRY DENSITY: WET DENSITY: LIQUID DEMAND: OPEN TIME: WATER RETENTION:

ADHESION STRENGTH ( PULL OFF ) COMPRESSIVE STRENGTH: FLEXURAL STRENGTH: THICKNESS FOR APPLICATION: COVERAGE AREA: POWDER + LIQUID DARK GREY PORTLAND CEMENT

1.7 KG/L 1.9 KG/L

13.2 – 13.5 L/40 KG

APPLICATION - CLEAN THE SURFACES FROM DUST, DIRT, AND OTHER MATERIALS THAT MAY EFFECT THE BONDING STRENGTH.

- USE A CLEAN AND LEAKPROOF PAIL FOR MIXING.

- GRADUALLY PUT POWDER L-405 INTO THE WATER AND MIX THOROUGHLY UNTIL AN EVEN CONSISTENCY IS ACHIEVED FOR AROUND 2 MINUTES, ALLOW TO BE SETTLED FOR 10 MINUTES FOR ADDITIVES TO DISSOLVE. RE-STIR BEFORE USING. THE MIXTURE WILL BE STABLE FOR 3 HOURS.

- RE-STIR THE PASTA REGULARLY, BUT DO NOT ADD MORE WATER OR LIQUID L-800.

HEAVY DUTY TILE ADHESIVE L-405 STORAGE TIMES SHOULD NOT EXCEED 12 MONTHS.

(17)

TECHNICAL DATA SHEET

BUMA MORTAR

Hal. | 17

SPESIFIKASI PELAPIS ANTI BOCOR, K-900

CEMENTITIOUS WATER PROOFING

USES CEMENTITIOUS WATERPROOFING IS TWO COMPONENT PRODUCT THAT CONSIST OF LIQUID ACRYLIC MODIFIED AND POWDER (PC, FILLER, AND ADDITIVE). WHEN THE MIXTURE IS CURED, IT WILL BE ELASTIC, RUBBERY, AND WATERPROOFING, SUITABLE TO WET AREAS SUCH AS BATH ROOM, LAUNDRY ROOM, KITCHEN, CARPORT, BALCONY ETC.

 REDUCE COST. SPECIFICATIONS AND PROPERTIES TYPE: COLOUR: BINDER: AGGREGATE: ADDITIVES: DRY DENSITY: WET DENSITY: LIQUID DEMAND: OPEN TIME: WATER RETENTION: ADHESION STRENGTH ( PULL OFF ) COMPRESSIVE STRENGTH: FLEXURAL STRENGTH: THICKNESS FOR APPLICATION: COVERAGE AREA: POWDER + LIQUID DARK GREY PORTLAND CEMENT

1.7 KG/L 1.9 KG/L

13.2 – 13.5 L/40 KG

APPLICATION - CLEAN THE SURFACES FROM DUST, DIRT, AND OTHER MATERIALS THAT MAY AFFECT THE BONDING STRENGTH.

- USE A CLEAN AND LEAK-PROOF PAIL FOR MIXING.

- GRADUALLY PUT POWDER K-405 INTO THE WATER AND MIX THOROUGHLY UNTIL AN EVEN CONSISTENCY IS ACHIEVED FOR AROUND 2 MINUTES, ALLOW TO BE SETTLED FOR 10 MINUTES FOR ADDITIVES TO DISSOLVE. RE-STIR BEFORE USING. THE MIXTURE WILL BE STABLE FOR 3 HOURS.

- RE-STIR THE PASTA REGULARLY, BUT DO NOT ADD MORE WATER OR LIQUID L-405.

HEAVY DUTY TILE ADHESIVE K-900 STORAGE TIMES SHOULD NOT EXCEED 12 MONTHS.

(18)