Renewable Energy Automatic Switch For Home Application.

(1)

RENEWABLE ENERGY AUTOMATIC SWITCH FOR HOME APPLICATION

NUR AMANI BINTI NOR IDI

This Report Is Submitted In Partial Fulfillment of Requirements for the Degree of Electrical Engineering (Industrial Power)

Faculty of Electrical Engineering

UNIVERSITI TEKNIKAL MALAYSIA MELAKA

(2)

“I hereby declare that I have read through this report entitle “Renewable Energy Automatic Switch for Home Application” and found that it has comply the partial fulfillment for awarding the degree of Bachelor of Electrical Engineering (Industrial Power)”

Signature : ………

Supervisor’s Name : MR. FARHAN BIN HANAFFI

(3)

I declare that this report entitle “Renewable Energy Automatic Switch for Home Application” is the result of my own research except as cited in the references. The report has not been accepted for any degree and is not concurrently submitted in candidature of any other degree.

Signature : ………

Name : NUR AMANI BINTI NOR IDI

(4)

Special dedicated to

My beloved father and mother

Mr Nor Idi Bin Ayob and Mrs Hamidah Khairuddin

My inspirational Motivator

Mr Farhan Bin Hanaffi

Special Invitation

Mr Aminurrashid Noordin

And

Mr Musa Bin Lada

All my fellow friends,

(5)

ACKNOWLEDGEMENT

First of all, I would like to express my thankfulness and gratitude to Allah S.W.T who has given me all the strength that I needed to complete this final year project and also prepare this report.

With this opportunity, I would like to express my gratitude to the Faculty of Electrical Engineering (FKE), Universiti Teknikal Malaysia Melaka (UTeM) generally, and especially to my supervisor Mr Farhan Bin Hanaffi because helped, advised and guided me during complete this final progress report. Besides, I would like to thanks to Mr Aminurrashid Bin Noordin and Mr Musa Bin Lada because they were guided and helped especially during completed task of the programming and the simulation.

(6)

ABSTRACT

(7)

ABSTRAK

Projek ini mencadangkan tentang tenaga yang boleh diperbaharui dengan digunakan sebagai sumber tenaga yang berkaitan untuk peralatan di rumah. Sumber-sumber tenaga yang boleh diperbaharui adalah daripada beberapa Sumber-sumber seperti tenaga suria, tenaga angin dan tenaga ombak dengan menjanakan bekalan arus elektrik. Tenaga suria ialah salah satu sumber tenaga yang digunakan secara meluas di dalam sumber tenaga yang boleh diperbaharui selain tanpa dikenakan sebarang kos dan tenaga yang dijamin bersih. Renewable Energy Automatic Switch direka dan disambungkan di antara sumber utama dan sumber tenaga yang boleh diperbaharui untuk diaplikasikan kepada kawasan perumahan. Sistem pengawal akan dijalankan oleh Programmable Intelligent Controller (PIC16F877A) iaitu fungsi sebagai litar kawalan untuk berkomunikasi antara suis dan

(8)

vii

CHAPTER TITLE PAGE

2.6.3 Buck-Boost Converter 12

2.6.4 Converter Comparison 13

2.7 Inverter 13

2.7.1 Classification of Inverter 14

2.7.2 Current Sources Inverter (CSI) 14

2.7.3 Voltage Source Inverter (VSI) 15

2.8 Characteristic of Photocell (LDR) 15

3 METHODOLOGY 18

3.1 Introduction 18

3.2 Research and Literature Review 19

3.3 Development of Hardware 20

3.3.1 Operation of Automatic Switch 21

3.3.2 Input Sensor 21

3.3.3 Relay with PIC Microcontroller 22

3.3.4 Software Design 23

3.3.5 Testing for Hardware 23

3.3.6 Analog Voltage Reading Method 25

3.4 Simulation 27

3.4.1 Boost Converter Simulation 28

3.4.2 Design Procedure of Converter Simulation 28

3.4.3 Inverter Design Simulation 29

3.5 Analysis Phases 30

4 RESULTS 31

4.1 Introduction 31

4.2 Implementation of Hardware Result 31

4.2.1 Input Sensor Device of Variable Resistor 32

4.2.2 Input Sensor Device of LDR 33

(10)

ix

CHAPTER TITLE PAGE

4.2.4 Relay 5VDC 35

4.2.5 Load of Circuit 36

4.3 Implementation of Simulation Result 37

4.3.1 Converter Design of Simulation Circuit 37

4.3.2 Inverter Design of Simulation Circuit 42

5 ANALYSIS AND DISCUSSIONS 45

5.1 Introduction 45

5.2 Analysis and Testing Hardware 45

5.2.1 Relationship between Voltage and Resistor 46

5.2.2 Performance of Automatic Switch 47

5.3 Analysis of Testing Simulation 50

5.3.1 Ripple Boost Converter Analysis 50

5.3.2 Analysis harmonic waveform 51

6 CONCLUSION 52

6.1 Introduction 52

6.2 Conclusion 53

6.3 Recommendation 53

REFERENCES 54

(11)

x

LIST OF TABLES

TABLE TITLE PAGE

2.1 Renewable Energy resource potential in Malaysia 6

2.2 Characteristic and features of photocell 16

3.1 Analog Voltage based on Photocell resistance 26

4.1 The value of variable resistor and input voltage 32

(12)

xi

LIST OF FIGURES

FIGURE TITLE PAGE

2.1 Buck Converter Circuit 10

2.2 Voltage and current changes 10

2.3 Boost Converter Circuit 11

2.4 Voltage and current waveform 11

2.5 Buck-Boost Converter Circuit 12

2.6 Buck-Boost Converter Circuit 12

2.7 Comparison voltage ratio between types of converter 13

2.8 Typical construction of photocell 16

3.1 Flow Chart of development project 19

3.2 Hardware and Software Design 20

3.3 Relay 5VDC is connected to microcontroller 22

3.4 The schematic diagram of the microcontroller circuit 23

3.5 Check value of input voltage at the port PIC before switch on 24

3.6 Testing circuit of hardware during simulation 25

3.7 Block diagram of simulation of power sources 27

3.8 Block Diagram of Boost Converter 28

3.9 Boost Converter Circuit 29

4.1 Block diagram of hardware result 31

4.2 Port of the base PIC16F877A 34

4.3 Relay connected to microcontroller 35

4.4 Controller Circuit connected to the lamp 36

4.5 Block diagram of simulation parts 37

4.6 Boost Converter Circuit simulation 38

(13)

xii

FIGURE TITLE PAGE

4.8 Average input current boost converter 39

4.9 Average value of voltage on the diode 40

4.10 Average value of voltage equal to 24VDC 41

4.11 Inverter circuit design 42

4.12 Output voltage inverter equal to 24VAC 43

4.13 Output Current value of 24VAC 44

4.14 Output voltage between 24VDC and 240VAC 44

5.1 Relationship between Voltage and LDR 46

5.2 Relationship between Voltage and Variable Resistor 47

5.3 Testing 1Waveform of 240VAC during switch on relay 48

5.4 Testing 2 Waveform of 240VAC during switch on relay 48

5.7 Voltage ripple at output voltage of boost converter 50

(14)

xiii

LIST OF APPENDICES

APPENDIX TITLE PAGE

A Gann chart of Project 55

B Coding of PIC16F877A 56

(15)

CHAPTER 1

INTRODUCTION

1.1 Overview of Project

The Renewable Energy such as the resources that would implement in this project. Generally, input power sources connected to the home is come from the Tenaga Nasional Berhad (TNB). The generation comes from power sources such as gas, hydroelectric, and coal as resources to produce the electricity. Malaysia such as the country has a good mixed of energy sources. As an alternatively way, the renewable energy sources has been used to replace it and to generate the electricity.

The most of power sources are come from the solar energy. Solar energy such as a large resource comes from the sunlight which is free of pollution. In Malaysia, the renewable energy provides more benefits to remain strong include an improved balance of trade, foreign exchange savings, more competitive industries, new export markets, employment opportunities, lower consumer prices and improvement of environment.

(16)

2

1.2 Problem Statement

Nowadays, the global warming issue was emphasizing into our earth from the energy sources that we used every day. The solution to this problem being the low level of the temperature of global warming, renewable energy sources is the best way to generate electricity. The renewable energy includes solar, wind, hydropower, biomass and geothermal. Besides, an orientation in tropical and whether country such as Malaysia, solar energy has more potential utilized in wide range of application growing rapidly.

The renewable energy as solar energy currently less used in the residential because of cost is expensive to build the system. Towards, to improve the performance and this critical issue, the solar energy used to solve this problem. Moreover, by improvement the system, the automatic switch has controlled to help human on the way to select primary or secondary power sources.

(17)

3

1.3 Objectives of Project

The several objectives of this project that need to be accomplished in developing renewable energy automatic switching. These projects intend to achieve the following objectives:

i. To design and develop switch two power supply from TNB or renewable energy

ii. To use and optimize renewable energy as secondary power sources iii. To simulate and design system energy sources circuit using OrCAD

1.4 Scopes of Project

The way to achieve the several objectives, this project needs to be implementing as below:

i. To design and build automatic switch 240VAC/50Hz between two sources ii. The controller use by PIC16F877A microcontroller in this project

iii. Automatic switch operates through Light Dependent Resistor (LDR) iv. OrCAD simulation to design circuit for inverter, converter and battery v. Limiting energy sources for a vital load such as lighting

1.5 Project Outline

(18)

4

In addition, Chapter Three explained the methodology about this project in developing the automatic switches consist of software, hardware and simulation implementation. The literature review of this project focuses on solar power energy. This chapter describes the entire project designed involved which in hardware, software and simulation development.

(19)

CHAPTER 2

LITERATURE REVIEW

2.1 Introduction

This chapter will be discussing the research and study about this project consists of the statistic of the renewable energy. Besides, the implementation of the hardware and simulation of this project which parts of the power electronic briefly explained in this chapter.

2.2 Statistic Renewable Energy in Malaysia

Malaysia has tremendous reserve of both non-renewable and renewable sources of energy. The largest non-renewable energy source found in Malaysia is petroleum (oil and gas) which is actively exploited. Although, Malaysia has some coal deposits only a small percentage is being mined. The two abundant renewable energy sources in Malaysia are biomass and solar. [1]

Malaysia recorded a total available capacity of electricity generation at 19,296.7MW in 2003. With regarded to electricity generation mix, the share of natural gas, coal, hydropower, fuel oil and diesel oil were 65%, 24%, 6.3% and 1.5% respectively in 2003. [1]

(20)

6

Identification two renewable energy sources to exploit are palm oil waste and the largest resources that can easily be development the solar, particular for rural electrification and water heating. The potential for solar power is great, given that Malaysia receives between 4.5 to 8 hours of sunshine per day and as equatorial country, a substantial amount of solar radiation year around. [1]

[image:20.612.96.530.260.461.2]

Moreover, a recent renewable energy study identified the renewable energy resource potential in Malaysia has showed in the Table below which in US Dollar value.

Table 2.1: Renewable Energy resource potential in Malaysia

Renewable Energy Resource Eenrgy Value in US$ Million (Annual)

Forest Residues 3,154

Palm Oil Biomass 1,679

Solar Thermal 796

Mill Residues 220

Hydro 133

Solar PV 100

Municipal Waste 50

Risk Husk 20

Landfill Gas 1

Source: Ministry of Energy. Water and Commnicatios Conversion rate: US$1 equals RM 3.8

2.3 Solar Energy Power in Malaysia

(21)

7

Since Malaysia is situated in the equatorial region with an average radiation of 4,500 KWh per square meter, it is an ideal location for large scale solar power installations. Considering that Malaysia gets on an average 4.5 hours to 8 hours of free and bountiful sunshine every day, the potential for solar power generation is very high. However, the real harnessing of this renewable energy source is way below its actual potential. [2]

A few remedial measures are:

i. Create awareness among the people through various programs about the benefits of solar power. Extensive details of information should be publicized pertaining to technology, financial aspects, support services, legal requirements, and environmental advantages.

ii. Incentives can be provided and credit guarantee schemes can be established to make solar power attractive.

iii. Imposing effective pricing laws taking into consideration the technology, the size and location of the plant.

iv. Gradually reduce the subsidies given to conventional energy and alternatively provide them to renewable energy.

(22)

8

2.4 PIC16F877A 40-Pin CMOS Flash Microcontroller

As defined by James L. Atonakos, microcontrollers are actually sopped-up microprocessors with build-in features such as RAM, ROM, Interval timers, parallel I/O ports and even A/D. The PIC16F877A is a powerful flash microcontroller that has many features in a 40-pin DIP package. [6]

Microcontroller differs from microprocessor in many ways. First and the most important is it functionality. These are the several advantages and the features of the PIC microcontroller such as speed capability, versatility and security.

i. Speed – the PIC has an internal division that divides by four connected between the oscillator and the internal block bus. This makes instruction times easy to calculate, especially if using 4MHz Crystal. Each instruction cycle then works out at one microsecond (1us).

ii. Versatility – the PIC is versatility micro and in volume as low cost solution to replace even a few logic gates which where space is at a premium.

iii. Security – the PIC has a code protection facility, which is one of the best in the industry.

2.5 Component of Solar Energy System

Due to the nature of solar energy, two components are required to have a functional solar energy generator. These two components are a collector and a storage unit. The collector simply collects the radiation that falls on it and converts a fraction of it to other forms of energy (either electricity and heat or heat alone). The storage unit is required because of the non-constant nature of solar energy; at certain times only a very small amount of radiation will be received. [3]

(23)

9

during the periods of maximum productivity, and release it when the productivity drops. In practice, a backup power supply is usually added, too, for the situations when the amount of energy required is greater than both what is being produced and what is stored in the container. [3]

Moreover, in this project the component design of the simulation tack are inverter and converter equipment system. Converter is used to convert from small or large value of voltage directly current (DC) to get the output value whether increase or decrease. Besides, for inverter system is converting from direct current voltage to alternating current (AC) voltage.

2.6 DC-to-DC Converters

Different type of dc-to-dc converters are widely used for dc drives in traction (electric trains), electric vehicles (EV), electric cars, trolley cars, golf carts, forklift trucks and switched-mode power supplies (SMPS). Moreover, there are numerous application in solar photovoltaic (PV) cell based power generation systems. At presents, PV based dc-to-dc converters are extensively used in space applications, lighting applications in remote areas and PV based water pumping systems. [4]

A DC-to-DC converter is a device that accepts a DC input voltage and produces a DC output voltage. Typically the output produced is at a different voltage level than the input. In addition, DC-to-DC converters are used to provide noise isolation, power bus regulation, etc. This is a summary of some of the popular DC-to-DC converter topologies: [5]

(24)

10

2.6.1 Buck Converter

In this circuit the transistor turning ON will put voltage Vin on one end of the

inductor. This voltage will tend to cause the inductor current to rise. When the transistor is OFF, the current will continue flowing through the inductor but now flowing through the diode. We initially assume that the current through the inductor does not reach zero, thus the voltage at Vx will now be only the voltage across the conducting diode during the full

OFF time. The average voltage at Vx will depend on the average ON time of the transistor

[image:24.612.186.450.283.386.2]

provided the inductor current is continuous. Figure 2.1and Figure 2.2 showed that buck of converter circuit. [7]

Figure 2.1: Buck Converter Circuit

[image:24.612.214.409.442.581.2]

Renewable Energy Automatic Switch For Home Application.