SINTESIS POLIURETAN MELALUI POLIMERISASI DIFENIL METANA 4,4 DIISOSIANAT (MDI)DENGAN POLIOL HASIL
HIDROKSILASI MINYAK BUAH ALPUKAT
ABSTRAK
Polimerisasi antara senyawa poliol dengan isosianat dapat menghasilkan poliuretan yang memiliki beragam bentuk.Poliol yang digunakan dalam hal ini dapat bersumber dari alam maupun juga hasil sintesis.Pada sintesis poliuretn ini memanfaatkan buah alpukat rusak sebagai sumber minyak dalam pembuatan poliol untuk menghasilkan poliuretan.Minyak alpukat diepoksidasi dengan asam performiat (HCOOOH) dengan menggunakan katalis H2SO4 pada suhu 40-450C
diikuti reaksi hidrolisis untuk menghasilkan senyawa poliol. Poliol yang terbentuk setelah dimurnikan dilakukan konfirmasi struktur melalui analisis spektroskopi FT-IR. Kemudian poliol direaksikan dengan difenil metana 4,4 diisosianat (MDI) dimana rasio (poliol : MDI) = 9:1 ; 8:2 ; 7:3 ; 6:4 ; 5:5 (v/v) dengan volume total 10 ml melalui pengadukan dalam sistem terbuka pada suhu 40-450C untuk menghasilkan poliuretan. Karakterisasi bentuk hasil reaksi diamati secara visual diikuti penentuan nilai kandungan gel, densitas dan analisis struktur dengan spektrofotometer FT-IR. Hasil reaksi dari poliol minyak alpukat dengan Difenil
Metana 4,4 Diisosianat dari setiap rasio pencampuran menghasilkan poliuretan
dengan kandungan gel antara 74,63% hingga 99,8% dimana dengan bertambahnya rasio MDI, nilai kandungan gel semakin tinggi. Hasil penentuan densitas dari poliuretan yang terbntuk antara 0,1341gr/cm3 hingga 0,7220 gr/cm3. Hasil analisis spektrofotometer FT-IR terhadap poliuretan yang dihasilkan ditandai dengan munculnya puncak-puncak vibrasi pada daerah bilangan gelombang 3400-3300 cm-1, 2270 – 1940 cm-1, 1700-1600 cm-1 dan 1590-1540 cm-1 yang merupakan karakteristik gugus fungsi uretan.
Kata kunci : Minyak Alpukat, Hidroksilasi, Poliol, MDI, Polimerisasi, Poliuretan.
SYNTHESIS POLYURETHANE BY POLYMERIZATION DIPHENYL METHANE 4,4 DIISOCYANATE (MDI) WITH POLYOL FROM
HYDROXILATED AVOCADO OIL
ABSTRACT
Polymerization between polyol compound with isocyanate can produce polyurethane that had different forms. Polyol that used in this case can be sourced from nature and also results from synthesis. On synthesis of this polyurethane was utilizing the damaged avocado as an oil source in the manufacture of polyols the polyols to produce polyurethane. avocado oil was reacted with performic acid (HCOOOH) using H2SO4 as catalyst at 40 – 45⁰C followed by hydrolysis to
produce polyol. Polyol that formed after purified confirmated by FT-IR spectroscopy, and then polyol was reacted to diphenyl methane 4,4 diisocyanate (MDI) at ratio 9:1; 8:2; 7:3; 6:4; and 5:5 (v/v) with a total volume 10 ml through stirring at open system at 40-45⁰C to produce polyurethane. Characterization of reaction products was observed visually and followed by determination of gel content ,density and confirmation structure by FT-IR spectroscopy analysis. Product of reaction from hydroxilated and avocado oil with diphenyl methane 4,4 diisocyanate from each mixing ratio produce polyurethane with gel content between 70,12% up to 96,29%, where increasing of MDI ratio, will increase the gel content. Density analysis resulted of density polyurethane between 0,1341gr/cm3 up to 0,7220gr/cm3. FT-IR spectroscopy analysis resulted of polyurethane was marked with vibration peaks at 3400-3300 cm-1, 2270 – 1940 cm-1, 1700-1600 cm-1 and 1590-1540 cm-1that show the characteristic of urethane groups.
Keywords : Avocado oil, Hydroxilation, Polyol, MDI, Polimerization, Polyurethane.