Instruction Manual for the Base Topology Packet Tracer Activity
Overview
1. When you open the Packet Tracer file, you will see two separate windows
Window A is you workspace window. Window B is the instruction window and provides the steps to complete the activity. In the lower left corner of Window B, there is a check box. Click in the box so that Window B always remains on top.
Note: If the instruction window disappears, check the task bar. You will find two packet tracer files
A
There is a standard Windows menu across the top with a row of icons below. As with all Windows applications, when you roll your mouse over an icon, a popup will appear telling you what that icon is (A)
In the lower left corner, you will see all of the components which can be added to your network. When you roll your mouse over any of the icons in the far left corner, its name will be displayed (B). When you click an icon, all of the available devices will appear (C).
On the right-hand side of the workspace window, there are additional icons. The top six (D) can be used to adjust your workspace. For example, the red X is used to delete a component from your workspace. You can also add PDU’s (packet data units) and use a simulation mode.
B
C
A
Step 1/12
1. The first task given in the instruction box is to drag out two generic routers. The indicator in parentheses is the Packet Tracer name for that device. Click on the router icon in the lower left corner. All of the router choices appear in the next box. Use your mouse to roll over each choice; the Packet Tracer name will appear in the text box underneath the icons.
workspace, a window will open with several tabs (depending on the device).
The Config tab allows you to choose global settings, configure routing, and configure any installed interfaces (since this router is empty, there are no interfaces listed at this time).
Changing the display name (A) changes what shows up on the Packet Tracer workspace; changing the Hostname (B) sends a command to the router and alters the router’s configuration. When you make changes, click in the Equivalent IOS Commands box (C) and observe the commands.
The Physical tab allows you to configure your device (in this case it’s a router) with the correct module for the network.
To add a module, you must first power off the unit
Drag the correct module from the modules listed (A) into the first empty
B
A
A
B
3. After you have added the proper modules, the ACME router should look as indicated by A.
Note: If you need to change a module that is already installed, turn off the router and drag the module back on top of the list.
In the lower right corner of the instruction window, you will see the status of this activity by percent completed, and steps. There are navigation arrows to take you to the next step, or to go back to the previous step for review (B).
1. Use the Config tag to perform task A. Use the Physical tab to perform task B.
A
A
B
2. Click the lightning bolt icon at the lower left to show connections. Connections are the cables you can use to connect all of the network devices. The cable you want to use is the Serial DCE.
3. When you select a cable, your mouse will turn into a plug icon to indicate that you are making a connection. Click on the ACME router. From the popup, select Serial0/0 (A). Drag your mouse over and click on the ISP router. When the popup appears, select Serial0/0 for this router.
4. When connected, the routers will look as follows:
Click on the icon in the bottom right corner of the instruction window to go to the next step.
1. Since we have added modules to the router, we can now configure those interfaces. Notice the interfaces listed on the left side of the Config tab. Adding the PT-ROUTER-NM-1S module adds the Serial0/0 interface. Adding the first PT-ROUTER-NM-1CE module adds the FastEthernet1/0 interface. Adding the second PT-ROUTER-NM-1CE module adds the FastEthernet2/0 interface.
2. Configure the FastEthernet1/0 interface as indicated in the instruction window. Make sure that you turn on the Port Status.
4. Click on the Serial0/0 Interface button to configure the interface as follows:
1. Configure the ISP router interfaces as follows:
Step 5/12
1. Select the Switches icon from the lower left corner of the workspace window. Drag three 2950-24 switches into your workspace.
2. Again, Packet Tracer assigns default names for the devices (Switch0, Switch1, and Swicth2). Click each switch and change its name on the Config tab.
3. Make the required connections between the switches and routers. You will see three different indicators. The green indicator shows that an interface is up. The orange indicator shows that an interface is in the process. A red indicator shows that a connection is down. These connections simulate the real devices and take a few seconds before they come up to a green status.
4. On the instruction window, advance to the next step.
Red Indicator
Step 6/12
1. In the lower left corner of the workspace window, click on End Devices to add the three generic workstations to your network.
2. Packet Tracer gives the workstation default names (PC0, PC1, and PC2).
3. Remember, when you select the connections icon and choose the Copper Straight-Through cable, your mouse will change to a plug icon allowing you to select the proper interface from each device to establish the connection.
1. Select Wireless Devices from the lower left of the workspace window and choose the generic access point (labeled Access-Point PT-N)
2. After selecting the access point, select the Config tab to change the name.
Step 8/12
1. Select End Devices in the lower left corner (A). You can then drag out two generic laptops (B).
2. Select the Physical tab and scroll down so that you can see the bottom of the laptop (C).
3. Turn off Laptop0 (A). Drag the network interface card onto the module list (B). Drag the PT-LAPTOP-NM-1W card into the empty slot (C). Power the laptop back on.
4. Make the same changes to Laptop1. Note the wireless connection between the access point and the laptop when the changes are complete.
5. Advance the instruction window to the next step.
A
B
C
A
B
1. The End Devices icon in the lower left corner of the workspace window will allow you to select the generic server.
Step 10/12
1. Select Connections from the lower left corner of the workspace window. All of the servers will connect to the ACME_DMZ switch with the Copper Straight-Through cable.
Remember, when you select the Copper Straight-Through cable, you will see a plug as your mouse icon allowing you to make the connection.
1. For each server, assign a static IP Address. Whenever a static IP Address is used, you must supply the IP Address, the Subnet Mask address, the Default Gateway address and a DNS Server address (DNS is required to resolve an IP address to the domain name used for web browsing). The DNS server for this network is the server just added to the ACME_DMZ network and its IP address is 192.168.2.201. The IP address for a DNS server must be a static address.
In this exercise, select the Desktop tab, IP Configuration to complete the addressing.
Step 12/12
1. Add a generic workstation to your workspace. After connecting this device with a Copper Straight-Through cable, click on the workstation and use the Desktop tab to assign the static IP address.
1. Click on the Check Results button at the bottom left of the instruction window.
Assessment Items
1. All of the items being assessed are listed in this window. Look for any item that has an X next to it (A).
2. To fix the error, click the Close button (B). When the Activity Results window closes, you will see the Packet Tracer activity. Use the arrows in the lower right of the instruction window if you want to view previous steps.
A
4. After making the correction, click in the Equivalent IOS Commands box to make sure the command took.
6. Congratulations. You have completed this activity successfully.
7. Click the Close button.
